Aktuelles Duck-Trick RAMFS Release **Support Thread**

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ach scheisse stimmt ja hmm dann kill die box mal im betrieb mit hardreset. eventuell fixt fsck irgend was

 

[olaf]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

OK ein Versuch ist es wert.

EDIT : Das war es. Sonst habe ich immer brav einen Neustart gemacht. Nun einfach Stecker raus , bis 20 gezählt, Stecker wieder rein und es funzt. fsck hat laut Display auch was gemacht. Aber ich konnte nicht erkennen was. Kann man das überhaupt?


gruß olaf und mal wieder ein extra DANKE an dich

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

muss erstmal weiter arbeiten , sonnst komm ich heut garnicht mehr heim viel erfolg

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ja du kannst im TeamCS Menü das letzte FSCK Log aufrufen ich tippe mal ganz einfach das es dir die Datei /etc/network/interface zerschossen hatte und dadurch Enigma2 keine neue erstellen kann FSCK Richtet das aber ganz fein


EDIT

Ist doch echt toll das auch mal was so läuft wie geplant

 

[lastsamurai]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

So ihr lieben , Update V126 ist Online

Du musst angemeldet sein, um Bilder zu sehen.

ne menge für den Vip2 drin

Du musst angemeldet sein, um Bilder zu sehen.

Gibts irgendwo einen Changelog von der 126 und der 127?
Gruß
Stephan

 

[meitevau]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Mit der 126 wurden funktioniernde Treiber für den VIP2 eingebaut, damit die TwinTuner-Funktionalität endlich funktioniert, wie gewünscht.

Dadurch passierte aber das hier:

Tuner: VIP1v2 Sharp Der funktioniert nun nicht mehr.

Update schief gelaufen oder iwas anderes falsch gemacht???
(Nochmal neu gewählt im menü und Neustart hat nicht geholfen)

Dies wiederum wurde mit 127 behoben.

meitevau

 

[lastsamurai]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Ah, top - danke!

Mal ne Frage zu der 2-Tuner-Konfiguration: ist es egal, ob ich das Signal durch den Receiver schleife oder ob ich an der Antennenbuchse in der Wand einen Verteiler davorsetze und 2 Kabel ziehe? Also in punkto Signalstärke etc.?

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

um alle programme entfangen zu können auf jeden tuner müssen entwerder zwei kabel von nen twim oder quad lnb kommen oder zwei von nen multischalter. bei duchgeschliffenen signal kannst du im falle einer aufnahme nur selbigen transponder schauen

 

[lastsamurai]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Oh, hätte vielleicht erwähnen sollen, dass ich Kabel hab und nicht SAT.

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ja dann reicht durchgeschliffen

 

[meitevau]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Update für das UpdatePack:
Link ist nicht mehr aktiv.

Es hat sich herausgestellt, dass die Update-Datei auf V124 Fehler hatte. Dies hat Duck-Trick korrigiert und ich diesbzgl. das UpdatePack V111-V127 neu zusammengepackt.

Edit: Getestet auf meiner Box auf der vorher V125 installiert war. Update hat tadellos funktioniert, es wird V127 angezeigt und keine Updates.

meitevau

 

[tamabi]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Hallo,
ich wollte mich auf diesem Weg ganz besonders bei Ducktrick und Meitevau für ihre Arbeit bedanken.
Jetzt endlich funktionieren auch bei mir beide Sharp Tuner und jetzt steht fest dass der VIP2 hier bleiben darf.
Habt echt eine Super Arbeit abgegeben und nicht aufgegeben, so wie es leider viele machen wenn sie vor einem scheibar unlösbaren Problem stehen.
Also, DANKE.
Macht weiter so!!!
Gruß tamabi

 

[Östrogen]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Erstmal:
Danke für diese tolle Image, und das beide Tuner jetzt laufen.
-
Leider habe ich bei Hotbird (schielend Astra+Hotbird) beim Zappen Abstürze.
Es werden dann auch z.B. bei manchen italienischen Programmen, statt der Programmnamen RAI1/RAI2/RAI3 die SID angezeigt. z.B. "10992V SID 0x213f"
Danach kommt der Green-Screen.
Neuer Sendersuchlauf brachte keinen Erfolg.

Danke für den Support.

Spoiler

<?xml version="1.0" encoding="utf-8"?><openpli>
<enigma2>
<crashdate>Thu Sep 12 09:21:39 2013</crashdate>
<compiledate>Apr 26 2013</compiledate>
<contactemail>somebody who cares</contactemail>
<!-- Please email this crashlog to above address -->
<skin>Elgato-HD/skin.xml</skin>
<sourcedate>2013-01-25</sourcedate>
<branch>last</branch>
<rev>ad7ef52</rev>
<version>3.0.0</version>
</enigma2>
<image>
<stbmodel>hl101</stbmodel>
<kernelversion>
<=!=[=C=D=A=T=A=[
Linux ArgusVIP 2.6.32.59_stm24_0211 #1 PREEMPT Fri Aug 30 19:58:24 CEST 2013 sh4 GNU/Linux
]=]=>
</kernelversion>
<kernelcmdline>console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk</kernelcmdline>
<nimsockets>NIM Socket 0:</nimsockets>
<imageversion>
<=!=[=C=D=A=T=A=[
version=0350200905300000
]=]=>
</imageversion>
<imageissue>
<!-- No such file or directory -->
</imageissue>
</image>
<crashlogs>
<enigma2crashlog>
<=!=[=C=D=A=T=A=[
escr<41>
SAT DVB-S freq 11116600, hor, pos 130, sr 27500000, fec 3
try to add 130 11116600 27500000 1 3 1
successfully scanned
TSID: 3070 ONID: 013e
descr<41>
SAT DVB-S freq 10992160, hor, pos 130, sr 27500000, fec 2
try to add 130 10992160 27500000 1 2 1
successfully scanned
TSID: 3390 ONID: 0071
descr<41>
SAT DVB-S freq 11158000, hor, pos 130, sr 27500000, fec 4
try to add 130 11158000 27500000 1 4 1
successfully scanned
TSID: 0258 ONID: 013e
descr<41>
SAT DVB-S freq 11316720, hor, pos 130, sr 27500000, fec 3
try to add 130 11316720 27500000 1 3 1
successfully scanned
TSID: 2cec ONID: 013e
descr<41>
SAT DVB-S freq 10815000, vert, pos 130, sr 27500000, fec 4
try to add 130 10815000 27500000 0 4 1
successfully scanned
TSID: 012c ONID: 013e
descr<41>
SAT DVB-S2 freq 11258000, vert, pos 130, sr 27500000, fec 3, modulation 2, rolloff 0
try to add 130 11258000 27500000 0 3 2
successfully scanned
TSID: 2134 ONID: 013e
descr<41>
SAT DVB-S freq 12399000, vert, pos 130, sr 27500000, fec 3
try to add 130 12399000 27500000 0 3 1
successfully scanned
TSID: 3200 ONID: 013e
descr<41>
SAT DVB-S freq 11075000, hor, pos 130, sr 27500000, fec 3
try to add 130 11075000 27500000 1 3 1
successfully scanned
TSID: 26ac ONID: 013f
descr<41>
SAT DVB-S2 freq 12692000, vert, pos 130, sr 27500000, fec 3, modulation 2, rolloff 0
try to add 130 12692000 27500000 0 3 2
successfully scanned
TSID: 2e7c ONID: 013e
descr<41>
SAT DVB-S freq 10892000, vert, pos 130, sr 27500000, fec 3
try to add 130 10892000 27500000 0 3 1
successfully scanned
TSID: 3264 ONID: 013e
descr<41>
SAT DVB-S2 freq 11096000, vert, pos 130, sr 29900000, fec 2, modulation 2, rolloff 0
try to add 130 11096000 29900000 0 2 2
successfully scanned
channel done!
FE_GET_PROPERTY failed (Invalid argument)
no channels left to scan.
100 channels scanned, 10 were unavailable.
96 channels in database.
remove 00820000 0071 1ce8
remove 00820000 0071 1e78
remove 00820000 0071 1edc
remove 00820000 0071 3390
remove 00820000 00b0 2e18
remove 00820000 00c8 0708
remove 00820000 0110 03de
remove 00820000 013e 00c8
remove 00820000 013e 012c
remove 00820000 013e 0190
remove 00820000 013e 01f4
remove 00820000 013e 0258
remove 00820000 013e 03e8
remove 00820000 013e 044c
remove 00820000 013e 0514
remove 00820000 013e 05dc
remove 00820000 013e 0640
remove 00820000 013e 06a4
remove 00820000 013e 1388
remove 00820000 013e 13ef
remove 00820000 013e 1450
remove 00820000 013e 1518
remove 00820000 013e 157c
remove 00820000 013e 17d4
remove 00820000 013e 1964
remove 00820000 013e 1b58
remove 00820000 013e 1bbc
remove 00820000 013e 1c20
remove 00820000 013e 1c84
remove 00820000 013e 1e14
remove 00820000 013e 1f40
remove 00820000 013e 1fa4
remove 00820000 013e 20d0
remove 00820000 013e 2134
remove 00820000 013e 22c4
remove 00820000 013e 2328
remove 00820000 013e 2454
remove 00820000 013e 24b8
remove 00820000 013e 2af8
remove 00820000 013e 2b5c
remove 00820000 013e 2bc0
remove 00820000 013e 2c88
remove 00820000 013e 2cec
remove 00820000 013e 2d50
remove 00820000 013e 2e7c
remove 00820000 013e 2ee0
remove 00820000 013e 2f44
remove 00820000 013e 2fa8
remove 00820000 013e 300c
remove 00820000 013e 3070
remove 00820000 013e 3138
remove 00820000 013e 319c
remove 00820000 013e 3200
remove 00820000 013e 3264
remove 00820000 013e 32c8
remove 00820000 013e 332c
remove 00820000 013e 33f4
remove 00820000 013e 3458
remove 00820000 013e 3bc4
remove 00820000 013e 3c28
remove 00820000 013e 3c8c
remove 00820000 013e 3cf0
remove 00820000 013e 3d54
remove 00820000 013e 3db8
remove 00820000 013f 23f0
remove 00820000 013f 26ac
remove 00820000 013f 3e1c
remove 00820000 02be 25e4
remove 00820000 fbff 0064
remove 00820000 fbff 0320
remove 00820000 fbff 14b4
remove 00820000 fbff 15e0
remove 00820000 fbff 1644
remove 00820000 fbff 16a8
remove 00820000 fbff 170c
remove 00820000 fbff 1838
remove 00820000 fbff 189c
remove 00820000 fbff 1900
remove 00820000 fbff 19c8
remove 00820000 fbff 1a2c
remove 00820000 fbff 1a90
remove 00820000 fbff 1af4
remove 00820000 fbff 1d4c
remove 00820000 fbff 2008
remove 00820000 fbff 206c
remove 00820000 fbff 2198
remove 00820000 fbff 2260
remove 00820000 fbff 251c
remove 00820000 fbff 2580
remove 00820000 fbff 2648
remove 00820000 fbff 2710
remove 00820000 fbff 2774
remove 00820000 fbff 2c24
remove 00820000 fbff 2db4
remove 0082acce 013e 0578
remove 0082afc2 0001 0065
main thread is non-idle! display spinner!
Renumbering...
---- saving lame channel db
saved 196 channels and 3763 services!
scan done!
action -> OkCancelActions ok
ok
action -> SetupActions cancel
playing 1:0:0:111:3070:13E:820000:0:0:0:
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
RemovePopup, id = ZapError
allocate channel.. 3070:013e
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 10992160 Pol 1 SR 27500000 INV 2 FEC 2 orbpos 130 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1242 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:0:111:3070:13E:820000:0:0:0:
allocate demux
[SEC] setTone 0
[SEC] sleep 25ms
[SEC] setVoltage 1
[SEC] sleep 20ms
set sequence pos 3
[SEC] invalidate current switch params
[SEC] sendDiseqc: e01038f4(?)
[SEC] sleep 50ms
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
[SEC] sleep 500ms
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x20c26e0 running
[eEPGCache] channel 0x20c26e0 running
stop release channel timer
ok ... now we start!!
[EPGC] next update in 2 sec
PATready
use pmtpid 1b59 for service_id 0111
FE_GET_PROPERTY failed (Invalid argument)
sdt update done!
action -> OkCancelActions cancel
eventNewProgramInfo 0 0
have 0 video stream(s), and 0 audio stream(s), and the pcr pid is 1fff, and the text pid is ffffffff
allocate demux
PES filter: DMX_SET_PES_FILTER - Invalid argument
decoder state: play, vpid=-1, apid=-1
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: (...)
[showCrypted]
[showDolby]
[showMp3]
not pauseable.
[eDVBCAService] new service 1:0:0:111:3070:13E:820000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:0:111:3070:13E:820000:0:0:0:
[eDVBCIInterfaces] gotPMT
action -> OkCancelActions cancel
[EPGC] start caching events(1378970410)
action -> OkCancelActions cancel
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[EPGC] nownext finished(1378970422)
[eDVBLocalTimerHandler] diff is -1
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 09:20:21
[eDVBLocalTimerHandler] m_time_difference is -1
[eDVBLocalTimerHandler] set Linux Time
[EPGC] schedule finished(1378970423)
action -> InfobarChannelSelection openServiceList
action -> ChannelSelectBaseActions showFavourites
action -> OkCancelActions ok
action -> OkCancelActions ok
playing 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:0:111:3070:13E:820000:0:0:0:
[eDVBCAService] free service 1:0:0:111:3070:13E:820000:0:0:0:
decoder state: play, vpid=-1, apid=-1
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x20c26e0
[eEPGCache] remove channel 0x20c26e0
[EPGC] abort caching events !!
allocate channel.. 03f3:0001
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 1 Freq 11361750 Pol 0 SR 22000000 INV 2 FEC 2 orbpos 192 system 1 modulation 2 pilot 2, rolloff 0
tuning to 1611 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:19:2B66:3F3:1:C00000:0:0:0:
allocate demux
set sequence pos 3
[SEC] setVoltage 2
[SEC] sleep 20ms
set sequence pos 3
[SEC] invalidate current switch params
[SEC] sendDiseqc: e01038f2(?)
[SEC] sleep 50ms
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
[SEC] sleep 500ms
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x20c26e0 running
[eEPGCache] channel 0x20c26e0 running
[EPGC] next update in 2 sec
stop release channel timer
ok ... now we start!!
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
PATready
use pmtpid 17d4 for service_id 2b66
FE_GET_PROPERTY failed (Invalid argument)
sdt update done!
eventNewProgramInfo 0 0
dvb subtitle PID 17f3 with wrong subtitling type (24)... force 0x10!!
have 1 video stream(s) (17de), and 4 audio stream(s) (17e8, 17e9, 17eb, 17ea), and the pcr pid is 17de, and the text pid is 17f2
allocate demux
decoder state: play, vpid=6110, apid=6120
DMX_SET_PES_FILTER(0x17de) - pcr - ok
DMX_SET_PES_FILTER(0x17e8) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 1 - ok
DMX_SET_PES_FILTER(0x17de) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x17f2) - ttx - ok
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
dvb subtitle PID 17f3 with wrong subtitling type (24)... force 0x10!!
[__evUpdatedInfo]
[writeChannelName]
vfd display text: ZDF HD
[showCrypted]
[showDolby]
[showMp3]
not pauseable.
[eDVBCAService] new service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCIInterfaces] gotPMT
AITready
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
[__evUpdatedEventInfo]
[EPGC] start caching events(1378970449)
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
action -> InfobarChannelSelection openServiceList
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
[EPGC] schedule finished(1378970458)
action -> ChannelSelectEPGActions showEPGList
ERROR reading PES (fd=55) - Value too large for defined data type
action -> EPGSelectActions info
[EPGC] nownext finished(1378970464)
[EPGC] stop caching events(1378970464)
[EPGC] next update in 60 min
action -> OkCancelActions cancel
action -> OkCancelActions cancel
action -> ChannelSelectBaseActions showFavourites
action -> OkCancelActions ok
action -> OkCancelActions ok
playing 1:0:1:213F:3070:13E:820000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:19:2B66:3F3:1:C00000:0:0:0:
[eDVBCAService] free service 1:0:19:2B66:3F3:1:C00000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
RemovePopup, id = ZapError
[eDVBLocalTimerHandler] remove channel 0x20c26e0
[eEPGCache] remove channel 0x20c26e0
allocate channel.. 3070:013e
(0)tune
RotorCmd ffffffff, lastRotorCmd ffffffff
prepare_sat System 0 Freq 10992160 Pol 1 SR 27500000 INV 2 FEC 2 orbpos 130 system 0 modulation 1 pilot 2, rolloff 0
tuning to 1242 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:213F:3070:13E:820000:0:0:0:
allocate demux
set sequence pos 3
[SEC] setVoltage 1
[SEC] sleep 20ms
set sequence pos 3
[SEC] invalidate current switch params
[SEC] sendDiseqc: e01038f4(?)
[SEC] sleep 50ms
set sequence pos 3
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
(0)fe event: status 0, inversion off, m_tuning 1
[SEC] sleep 500ms
(0)fe event: status 1f, inversion off, m_tuning 2
OURSTATE: ok
[eDVBLocalTimerHandler] channel 0x20c26e0 running
[eEPGCache] channel 0x20c26e0 running
stop release channel timer
ok ... now we start!!
[EPGC] next update in 2 sec
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
PATready
use pmtpid 0450 for service_id 213f
eventNewProgramInfo 0 0
have 1 video stream(s) (0200), and 2 audio stream(s) (028a, 02b6), and the pcr pid is 0200, and the text pid is 0240
allocate demux
decoder state: play, vpid=512, apid=650
DMX_SET_PES_FILTER(0x200) - pcr - ok
DMX_SET_PES_FILTER(0x28a) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x200) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x240) - ttx - ok
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Rai 1
[showCrypted]
[showDolby]
[showMp3]
not pauseable.
[eDVBCAService] new service 1:0:1:213F:3070:13E:820000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:213F:3070:13E:820000:0:0:0:
[eDVBCIInterfaces] gotPMT
[eDVBCAService] don't build/send the same CA PMT twice
AITready
FE_GET_PROPERTY failed (Invalid argument)
sdt update done!
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Rai 1
[showCrypted]
[showDolby]
[showMp3]
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 5
VIDEO_GET_EVENT - ok
[__evVideoSizeChanged]
VIDEO_GET_EVENT - ok
[EPGC] start caching events(1378970485)
action -> InfobarChannelSelection openServiceList
[__evUpdatedEventInfo]
crc32 failed! is 5049fed7


[EPGC] abort non avail netmed schedule reading
[EPGC] abort non avail netmed schedule other reading
[EPGC] abort non avail FreeSat schedule_other reading
[EPGC] abort non avail viasat reading
action -> OkCancelActions ok
action -> InfobarChannelSelection zapDown
action -> InfobarChannelSelection zapDown
playing 1:0:1:2140:3070:13E:820000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:1:213F:3070:13E:820000:0:0:0:
[eDVBCAService] free service 1:0:1:213F:3070:13E:820000:0:0:0:
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
start release channel timer
[__evStart]
[__evSeekableStatusChanged]
not pauseable.
RemovePopup, id = ZapError
use cached_channel
stop release channel timer
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:1:2140:3070:13E:820000:0:0:0:
ok ... now we start!!
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
[__evUpdatedEventInfo]
crc32 failed! is f00617f3


PATready
use pmtpid 0451 for service_id 2140
[EPGC] nownext finished(1378970498)
eventNewProgramInfo 0 0
have 1 video stream(s) (0201), and 3 audio stream(s) (028b, 02b7, 02b8), and the pcr pid is 0201, and the text pid is 0241
allocate demux
decoder state: play, vpid=513, apid=651
DMX_SET_PES_FILTER(0x201) - pcr - ok
DMX_SET_PES_FILTER(0x28b) - audio - ok
AUDIO_SET_BYPASS(1) - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 0 - ok
DMX_SET_PES_FILTER(0x201) - video - ok
VIDEO_PLAY - ok
DMX_SET_PES_FILTER(0x241) - ttx - ok
VIDEO_CONTINUE - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
AUDIO_CONTINUE - ok
disable teletext subtitles
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Rai 2
[showCrypted]
[showDolby]
[showMp3]
not pauseable.
[eDVBCAService] new service 1:0:1:2140:3070:13E:820000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:1:2140:3070:13E:820000:0:0:0:
[eDVBCIInterfaces] gotPMT
VIDEO_GET_EVENT - ok
unhandled DVBAPI Video Event 9
[__evUpdatedInfo]
[writeChannelName]
vfd display text: Rai 2
[showCrypted]
[showDolby]
[showMp3]
-------
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
]=]=>
</enigma2crashlog>
</crashlogs>
</openpli>

 

[meitevau]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Installiere mal mein UpdatePack:
Link ist nicht mehr aktiv.

Das Update V124 hatte einen Fehler, evtl. kannst Du damit Dein Problem auch lösen.

meitevau

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

könnte auch nen stick problem sein