Reparatur Pogo E02 mittels Raspi als Jtag

[joerg_999]

nicht relevant

 

[nuggelbeb]

ok

 

[joerg_999]

@nuggelbeb hast du Zeit?

 

[nuggelbeb]

ja

 

[joerg_999]

machen wir in private Nachrichten weiter

 

[nuggelbeb]

ok

 

[nuggelbeb]

Erst einmal Danke für die große Mühe.
Der Pogo startet aber noch nicht von dem neuen Stick. Ich lande immer noch bei LEDE
Haben wir was vergessen?

 

[joerg_999]

gib mir nochmals deine printenv von der Konsole
und wenn geht den bootlog..

 

[nuggelbeb]

Spoiler: bootlog

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 3917824 000ea0a4-01 83 Boot
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
## Error: "scan_disk" not defined
## Error: "set_bootargs" not defined
## Error: "load_uimage" not defined
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=1", size 127 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 1016, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3705113473
ubi0: available PEBs: 0, total reserved PEBs: 1016, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 800000
No size specified -> Using max size (1935360)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: ARM LEDE Linux-4.4.92
Created: 2017-10-17 17:46:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1810174 Bytes = 1.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Using machid 0xdd6 from environment

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.92 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Cloud Engines Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 254500K/262144K available (4082K kernel code, 142K rwdata, 652K rodata, 176K init, 201K bss, 7644K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04a7db4 (4736 kB)
[ 0.000000] .init : 0xc04a8000 - 0xc04d4000 ( 176 kB)
[ 0.000000] .data : 0xc04d4000 - 0xc04f7bc8 ( 143 kB)
[ 0.000000] .bss : 0xc04f7bc8 - 0xc052a27c ( 202 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000086] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090090] pid_max: default: 32768 minimum: 301
[ 0.090205] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090792] CPU: Testing write buffer coherency: ok
[ 0.091144] Setting up static identity map for 0x81e0 - 0x821c
[ 0.091390] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.095986] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.096014] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.096100] pinctrl core: initialized pinctrl subsystem
[ 0.097174] NET: Registered protocol family 16
[ 0.097545] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.098262] cpuidle: using governor ladder
[ 0.098592] Feroceon L2: Enabling L2
[ 0.098636] Feroceon L2: Cache support initialised.
[ 0.098912] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.116450] SCSI subsystem initialized
[ 0.117178] usbcore: registered new interface driver usbfs
[ 0.117255] usbcore: registered new interface driver hub
[ 0.117321] usbcore: registered new device driver usb
[ 0.118132] clocksource: Switched to clocksource orion_clocksource
[ 0.119019] NET: Registered protocol family 2
[ 0.119618] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119655] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119685] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.119742] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119765] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119912] NET: Registered protocol family 1
[ 0.121732] Crashlog allocated RAM at address 0x3f00000
[ 0.135685] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.135699] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.138398] io scheduler noop registered
[ 0.138412] io scheduler deadline registered (default)
[ 0.139626] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.140193] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated
[ 0.140550] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated
[ 0.171899] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.174877] console [ttyS0] disabled
[ 0.174950] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 0.623732] console [ttyS0] enabled
[ 0.628936] nand: Could not find valid ONFI parameter page; aborting
[ 0.635362] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.641770] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 0.646237] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.653863] Scanning device for bad blocks
[ 0.766265] 2 cmdlinepart partitions found on MTD device orion_nand
[ 0.772576] Creating 2 MTD partitions on "orion_nand":
[ 0.777738] 0x000000000000-0x000000100000 : "u-boot"
[ 0.784436] 0x000000100000-0x000008000000 : "ubi"
[ 0.791060] libphy: orion_mdio_bus: probed
[ 0.795967] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 0.804364] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address b6:d0:5e:0f:a1:17
[ 0.813177] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.819754] ehci-pci: EHCI PCI platform driver
[ 0.824281] ehci-platform: EHCI generic platform driver
[ 0.829677] ehci-orion: EHCI orion driver
[ 0.833859] orion-ehci f1050000.ehci: EHCI Host Controller
[ 0.839425] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 0.847238] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 0.868148] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 0.874877] hub 1-0:1.0: USB hub found
[ 0.878845] hub 1-0:1.0: 1 port detected
[ 0.883224] usbcore: registered new interface driver usb-storage
[ 1.198145] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.350286] hub 1-1:1.0: USB hub found
[ 1.354379] hub 1-1:1.0: 4 ports detected
[ 1.638142] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 1.750861] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 1.757526] scsi host0: usb-storage 1-1.1:1.0
[ 1.898143] rtc-mv f1010300.rtc: internal RTC not ticking
[ 1.903674] i2c /dev entries driver
[ 1.907909] orion_wdt: Initial timeout 21 sec
[ 1.915647] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.923893] NET: Registered protocol family 10
[ 1.929903] NET: Registered protocol family 17
[ 1.934416] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.947108] 8021q: 802.1Q VLAN Support v1.8
[ 1.953386] UBI: auto-attach mtd1
[ 1.956554] ubi0: attaching mtd1
[ 2.188068] ubi0: scanning is finished
[ 2.203567] ubi0: attached mtd1 (name "ubi", size 127 MiB)
[ 2.209109] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.216010] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.222757] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.229583] ubi0: good PEBs: 1016, bad PEBs: 0, corrupted PEBs: 0
[ 2.235700] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.242971] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3705113473
[ 2.252161] ubi0: available PEBs: 0, total reserved PEBs: 1016, PEBs reserved for bad PEB handling: 20
[ 2.261882] ubi0: background thread "ubi_bgt0d" started, PID 895
[ 2.268632] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.274146] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.281338] hctosys: unable to open rtc device (rtc0)
[ 2.292590] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.300301] Freeing unused kernel memory: 176K
[ 2.768999] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS
[ 2.779818] sd 0:0:0:0: [sda] 15630336 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 2.798195] sd 0:0:0:0: [sda] Write Protect is off
[ 2.803709] sd 0:0:0:0: [sda] No Caching mode page found
[ 2.809087] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 2.826572] init: Console is alive
[ 2.830352] init: - watchdog -
[ 2.893086] sda: sda1
[ 2.897923] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 3.033670] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.040871] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.058424] init: - preinit -
[ 3.418980] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.452663] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.484382] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.516629] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.546220] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.575673] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 3.585601] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 3.592729] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.613676] random: procd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.544630] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 6.554562] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.813959] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 971
[ 6.847847] UBIFS (ubi0:2): recovery needed
[ 6.998864] UBIFS (ubi0:2): recovery completed
[ 7.003410] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 7.011304] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.021281] UBIFS (ubi0:2): FS size: 122959872 bytes (117 MiB, 953 LEBs), journal size 6193152 bytes (5 MiB, 48 LEBs)
[ 7.031955] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 7.038617] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 9E10EE26-3F7D-4F6F-88C2-568D0A0C40BA, small LPT model
[ 7.052992] mount_root: switching to ubifs overlay
[ 7.061798] urandom-seed: Seeding with /etc/urandom.seed
[ 7.096392] procd: - early -
[ 7.099803] procd: - watchdog -
[ 7.917449] procd: - watchdog -
[ 7.920835] procd: - ubus -
[ 7.996394] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.006560] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.015900] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.024963] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.034976] procd: - init -
Please press Enter to activate this console.
[ 8.257482] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.266528] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.278454] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.287964] nf_conntrack version 0.5.0 (3979 buckets, 15916 max)
[ 8.312408] xt_time: kernel timezone is -0000
[ 8.323342] PPP generic driver version 2.4.2
[ 8.329243] NET: Registered protocol family 24
[ 8.336654] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.675385] device eth0 entered promiscuous mode
[ 11.690151] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 14.346765] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 14.357201] br-lan: port 1(eth0) entered forwarding state
[ 14.362675] br-lan: port 1(eth0) entered forwarding state
[ 14.369122] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 16.358147] br-lan: port 1(eth0) entered forwarding state
[ 60.048171] random: nonblocking pool is initialized



BusyBox v1.25.1 () built-in shell (ash)

_________
/ /\ _ ___ ___ ___
/ LE / \ | | | __| \| __|
/ DE / \ | |__| _|| |) | _|
/________/ LE \ |____|___|___/|___| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (17.01.4, r3560-79f57e422d)
\________\/ -----------------------------------------------------------

root@LEDE:/#

Spoiler: printenv

PogoE02> printenv
arcNumber=3542
baudrate=115200
bootargs=console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
bootcmd=run bootcmd_uenv; run scan_disk; run set_bootargs; run bootcmd_exec; run bootcmd_lede
bootcmd_exec=if run load_uimage; then; if run load_initrd; then if run load_dtb; then bootm $load_uimage_addr $load_initrd_addr $load_dtb_addr; else bootm $load_uimage_addr $load_initrd_addr; fi; else if run load_dtb; then bootm $load_uimage_addr - $load_dtb_addr; else bootm $load_uimage_addr; fi; fi; fi
bootcmd_lede=run set_bootargs_lede; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000
bootcmd_uenv=run uenv_load; if test $uenv_loaded -eq 1; then run uenv_import; fi
bootcmd_usb=run usb_init; run set_bootargs_usb; run usb_boot;
bootdelay=10
console=ttyS0,115200
device=0:1
dtb_file=/boot/dts/kirkwood-pogo_e02.dtb
ethact=egiga0
ethaddr=b6:d0:5e:0f:a1:17
fileaddr=800000
filesize=20000
ipaddr=192.168.178.26
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtddevname=u-boot
mtddevnum=0
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
nand_erasesize=20000
nand_oobsize=40
nand_writesize=800
partition=nand0,0
rootdelay=10
rootfstype=ext3
serverip=192.168.178.101
set_bootargs_lede=setenv bootargs console=ttyS0,115200 $mtdparts
set_bootargs_usb=setenv bootargs console=$console root=$usb_root rootdelay=$rootdelay rootfstype=$rootfstype $mtdparts
stderr=serial
stdin=serial
stdout=serial
uenv_import=echo importing envs ...; env import -t 0x810000
uenv_load=usb start; setenv uenv_loaded 0; for devtype in usb; do for disknum in 0; do run uenv_read_disk; done; done
uenv_loaded=0
uenv_read=echo loading envs from $devtype $disknum ...; if load $devtype $disknum:1 0x810000 /boot/uEnv.txt; then setenv uenv_loaded 1; fi
uenv_read_disk=if $devtype part $disknum; then run uenv_read; fi
usb_boot=mw 0x800000 0 1; run usb_load_uimage; if run usb_load_uinitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_init=usb start
usb_load_uimage=ext2load usb $device 0x800000 /boot/uImage
usb_load_uinitrd=ext2load usb $device 0x1100000 /boot/uInitrd
usb_root=/dev/sda1

Environment size: 2281/131068 bytes
PogoE02>

 

[joerg_999]

da ist was bei einspielen der boot envs passiert - der hat die neuen nicht geschrieben
stecke den debian Stick an und unterbrich den Bootvorgang dann
probieren wir folgendes aus der Konsole:
minimalen boot-envs zum starten aus dem u-boot:
Code:

setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb'
setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'

gestartet wird mit:

usb reset; run usb_boot

# wenn der Pogo in debian hochgefahren ist kann man von hier aus neue uboot-envs flashen.

 

[nuggelbeb]

NIX

Spoiler: log

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb'
PogoE02> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
PogoE02> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
PogoE02> setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'
PogoE02>

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found

Partition Map for USB device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type
1 2048 3917824 000ea0a4-01 83 Boot
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
## Error: "scan_disk" not defined
## Error: "set_bootargs" not defined
## Error: "load_uimage" not defined
ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: attached mtd1 (name "mtd=1", size 127 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 1016, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3705113473
ubi0: available PEBs: 0, total reserved PEBs: 1016, PEBs reserved for bad PEB handling: 20
Read 0 bytes from volume kernel to 800000
No size specified -> Using max size (1935360)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: ARM LEDE Linux-4.4.92
Created: 2017-10-17 17:46:20 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1810174 Bytes = 1.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Using machid 0xdd6 from environment

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.4.92 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine model: Cloud Engines Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 254500K/262144K available (4082K kernel code, 142K rwdata, 652K rodata, 176K init, 201K bss, 7644K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04a7db4 (4736 kB)
[ 0.000000] .init : 0xc04a8000 - 0xc04d4000 ( 176 kB)
[ 0.000000] .data : 0xc04d4000 - 0xc04f7bc8 ( 143 kB)
[ 0.000000] .bss : 0xc04f7bc8 - 0xc052a27c ( 202 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000009] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000086] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090090] pid_max: default: 32768 minimum: 301
[ 0.090205] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090224] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090792] CPU: Testing write buffer coherency: ok
[ 0.091145] Setting up static identity map for 0x81e0 - 0x821c
[ 0.091390] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.095986] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.096014] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.096100] pinctrl core: initialized pinctrl subsystem
[ 0.097174] NET: Registered protocol family 16
[ 0.097545] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.098262] cpuidle: using governor ladder
[ 0.098592] Feroceon L2: Enabling L2
[ 0.098636] Feroceon L2: Cache support initialised.
[ 0.098912] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.116448] SCSI subsystem initialized
[ 0.117173] usbcore: registered new interface driver usbfs
[ 0.117250] usbcore: registered new interface driver hub
[ 0.117316] usbcore: registered new device driver usb
[ 0.118129] clocksource: Switched to clocksource orion_clocksource
[ 0.119012] NET: Registered protocol family 2
[ 0.119611] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119648] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.119677] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.119734] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119757] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.119902] NET: Registered protocol family 1
[ 0.121721] Crashlog allocated RAM at address 0x3f00000
[ 0.135674] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.135689] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.138384] io scheduler noop registered
[ 0.138398] io scheduler deadline registered (default)
[ 0.139607] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 0.140171] irq: Cannot allocate irq_descs @ IRQ32, assuming pre-allocated
[ 0.140527] irq: Cannot allocate irq_descs @ IRQ64, assuming pre-allocated
[ 0.171883] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.174858] console [ttyS0] disabled
[ 0.174930] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 0.623770] console [ttyS0] enabled
[ 0.628970] nand: Could not find valid ONFI parameter page; aborting
[ 0.635400] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 0.641809] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 0.646276] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.653902] Scanning device for bad blocks
[ 0.766321] 2 cmdlinepart partitions found on MTD device orion_nand
[ 0.772633] Creating 2 MTD partitions on "orion_nand":
[ 0.777794] 0x000000000000-0x000000100000 : "u-boot"
[ 0.784487] 0x000000100000-0x000008000000 : "ubi"
[ 0.791104] libphy: orion_mdio_bus: probed
[ 0.796006] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 0.804408] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address b6:d0:5e:0f:a1:17
[ 0.813223] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.819792] ehci-pci: EHCI PCI platform driver
[ 0.824320] ehci-platform: EHCI generic platform driver
[ 0.829715] ehci-orion: EHCI orion driver
[ 0.833898] orion-ehci f1050000.ehci: EHCI Host Controller
[ 0.839461] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 0.847277] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 0.868146] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 0.874872] hub 1-0:1.0: USB hub found
[ 0.878841] hub 1-0:1.0: 1 port detected
[ 0.883218] usbcore: registered new interface driver usb-storage
[ 1.198142] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1.350328] hub 1-1:1.0: USB hub found
[ 1.354420] hub 1-1:1.0: 4 ports detected
[ 1.638139] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 1.750774] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 1.757444] scsi host0: usb-storage 1-1.4:1.0
[ 1.898139] rtc-mv f1010300.rtc: internal RTC not ticking
[ 1.903671] i2c /dev entries driver
[ 1.907905] orion_wdt: Initial timeout 21 sec
[ 1.915642] marvell-cesa f1030000.crypto: CESA device successfully registered
[ 1.923888] NET: Registered protocol family 10
[ 1.929906] NET: Registered protocol family 17
[ 1.934419] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.947110] 8021q: 802.1Q VLAN Support v1.8
[ 1.953391] UBI: auto-attach mtd1
[ 1.956557] ubi0: attaching mtd1
[ 2.188062] ubi0: scanning is finished
[ 2.203569] ubi0: attached mtd1 (name "ubi", size 127 MiB)
[ 2.209112] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[ 2.216013] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[ 2.222760] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
[ 2.229587] ubi0: good PEBs: 1016, bad PEBs: 0, corrupted PEBs: 0
[ 2.235703] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[ 2.242965] ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3705113473
[ 2.252146] ubi0: available PEBs: 0, total reserved PEBs: 1016, PEBs reserved for bad PEB handling: 20
[ 2.261871] ubi0: background thread "ubi_bgt0d" started, PID 895
[ 2.268620] block ubiblock0_1: created from ubi0:1(rootfs)
[ 2.274132] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[ 2.281326] hctosys: unable to open rtc device (rtc0)
[ 2.292576] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[ 2.300295] Freeing unused kernel memory: 176K
[ 2.769023] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS
[ 2.779875] sd 0:0:0:0: [sda] 15630336 512-byte logical blocks: (8.00 GB/7.45 GiB)
[ 2.798214] sd 0:0:0:0: [sda] Write Protect is off
[ 2.803741] sd 0:0:0:0: [sda] No Caching mode page found
[ 2.809114] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 2.826611] init: Console is alive
[ 2.830391] init: - watchdog -
[ 2.892997] sda: sda1
[ 2.897711] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 3.033616] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.040822] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.058382] init: - preinit -
[ 3.418965] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.452639] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.484334] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.516542] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.546115] random: jshn: uninitialized urandom read (4 bytes read, 16 bits of entropy available)
[ 3.575633] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 3.585564] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 3.592689] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.613615] random: procd: uninitialized urandom read (4 bytes read, 17 bits of entropy available)
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.354409] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 6.364339] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.815720] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 971
[ 6.849645] UBIFS (ubi0:2): recovery needed
[ 7.015005] UBIFS (ubi0:2): recovery completed
[ 7.019574] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[ 7.027443] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.037427] UBIFS (ubi0:2): FS size: 122959872 bytes (117 MiB, 953 LEBs), journal size 6193152 bytes (5 MiB, 48 LEBs)
[ 7.048095] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
[ 7.054753] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID 9E10EE26-3F7D-4F6F-88C2-568D0A0C40BA, small LPT model
[ 7.069157] mount_root: switching to ubifs overlay
[ 7.078012] urandom-seed: Seeding with /etc/urandom.seed
[ 7.112384] procd: - early -
[ 7.115345] procd: - watchdog -
[ 7.933208] procd: - watchdog -
[ 7.936561] procd: - ubus -
[ 8.012232] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.022395] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.031734] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.040795] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 8.050817] procd: - init -
Please press Enter to activate this console.
[ 8.273810] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.282867] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.294770] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.304336] nf_conntrack version 0.5.0 (3979 buckets, 15916 max)
[ 8.328830] xt_time: kernel timezone is -0000
[ 8.339788] PPP generic driver version 2.4.2
[ 8.345646] NET: Registered protocol family 24
[ 8.353246] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.698470] device eth0 entered promiscuous mode
[ 11.738324] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 14.311212] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 14.321649] br-lan: port 1(eth0) entered forwarding state
[ 14.327106] br-lan: port 1(eth0) entered forwarding state
[ 14.333501] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 16.318137] br-lan: port 1(eth0) entered forwarding state



BusyBox v1.25.1 () built-in shell (ash)

_________
/ /\ _ ___ ___ ___
/ LE / \ | | | __| \| __|
/ DE / \ | |__| _|| |) | _|
/________/ LE \ |____|___|___/|___| lede-project.org
\ \ DE /
\ LE \ / -----------------------------------------------------------
\ DE \ / Reboot (17.01.4, r3560-79f57e422d)
\________\/ -----------------------------------------------------------

root@LEDE:/#

 

[joerg_999]

Nicht den Pogo neu starten wir haben die envs nur temporär bei Neustart sind die weg, die sind nur zum einmaligen starten des debian sticks .
von dort machen wir anders weiter...
also eingeben wie oben und starten mit:

usb reset; run usb_boot

 

[nuggelbeb]

OK

Spoiler

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb'
PogoE02> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
PogoE02> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
PogoE02> setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'
PogoE02> usb reset; run usb_boot
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
10444 bytes read in 2845 ms (2.9 KiB/s)
3901632 bytes read in 600 ms (6.2 MiB/s)
6734831 bytes read in 653 ms (9.8 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.11.3-kirkwood-tld-2
Created: 2017-07-15 12:44:03 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3901568 Bytes = 3.7 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.11.3-kirkwood-tld-2
Created: 2017-07-15 12:44:13 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 6734767 Bytes = 6.4 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0f4a3000, end 0fb0f3af ... OK
Loading Device Tree to 0f49d000, end 0f4a28cb ... OK
Using machid 0xdd6 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.11.3-kirkwood-tld-2 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: CloudEngines Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 239836K/262144K available (8192K kernel code, 786K rwdata, 2016K rodata, 1024K init, 280K bss, 22308K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0900000 (9184 kB)
[ 0.000000] .init : 0xc0c00000 - 0xc0d00000 (1024 kB)
[ 0.000000] .data : 0xc0d00000 - 0xc0dc49b4 ( 787 kB)
[ 0.000000] .bss : 0xc0dc49b4 - 0xc0e0acc8 ( 281 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000493] Console: colour dummy device 80x30
[ 0.000528] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090112] pid_max: default: 32768 minimum: 301
[ 0.090314] Security Framework initialized
[ 0.090436] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090455] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091398] CPU: Testing write buffer coherency: ok
[ 0.092416] Setting up static identity map for 0x100000 - 0x100058
[ 0.092675] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.096264] devtmpfs: initialized
[ 0.100472] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.100499] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.100829] prandom: seed boundary self test passed
[ 0.104587] prandom: 100 self tests passed
[ 0.104600] pinctrl core: initialized pinctrl subsystem
[ 0.105789] NET: Registered protocol family 16
[ 0.106204] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.107812] cpuidle: using governor ladder
[ 0.107882] cpuidle: using governor menu
[ 0.108260] Feroceon L2: Enabling L2
[ 0.108307] Feroceon L2: Cache support initialised.
[ 0.108676] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.113325] No ATAGs?
[ 0.122356] vgaarb: loaded
[ 0.122674] SCSI subsystem initialized
[ 0.123149] usbcore: registered new interface driver usbfs
[ 0.123227] usbcore: registered new interface driver hub
[ 0.123308] usbcore: registered new device driver usb
[ 0.124327] clocksource: Switched to clocksource orion_clocksource
[ 0.212950] VFS: Disk quotas dquot_6.6.0
[ 0.213034] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.223706] NET: Registered protocol family 2
[ 0.224522] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.224560] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.224591] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.224680] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.224704] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.224875] NET: Registered protocol family 1
[ 0.225301] RPC: Registered named UNIX socket transport module.
[ 0.225314] RPC: Registered udp transport module.
[ 0.225321] RPC: Registered tcp transport module.
[ 0.225328] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.225631] Unpacking initramfs...
[ 0.837020] Freeing initrd memory: 6580K
[ 0.837118] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.838088] audit: initializing netlink subsys (disabled)
[ 0.838572] Initialise system trusted keyrings
[ 0.838705] audit: type=2000 audit(0.830:1): state=initialized audit_enabled=0 res=1
[ 0.838782] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.838875] zbud: loaded
[ 0.839846] NFS: Registering the id_resolver key type
[ 0.839872] Key type id_resolver registered
[ 0.839881] Key type id_legacy registered
[ 0.839899] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.839909] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.840382] Key type cifs.spnego registered
[ 0.840403] Key type cifs.idmap registered
[ 0.840416] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.840681] fuse init (API version 7.26)
[ 0.841068] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 0.841336] orangefs_init: module version upstream loaded
[ 0.841348] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 2.554333] random: fast init done
[ 4.958403] Key type asymmetric registered
[ 4.958420] Asymmetric key parser 'x509' registered
[ 4.958492] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 4.958504] io scheduler noop registered
[ 4.958513] io scheduler deadline registered
[ 4.958594] io scheduler cfq registered (default)
[ 4.959871] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 4.961727] mv_xor f1060800.xor: Marvell shared XOR driver
[ 5.015070] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[ 5.015295] mv_xor f1060900.xor: Marvell shared XOR driver
[ 5.075067] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[ 5.075500] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 5.076755] console [ttyS0] disabled
[ 5.076821] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 5.673352] console [ttyS0] enabled
[ 5.685487] loop: module loaded
[ 5.689811] nand: Could not find valid ONFI parameter page; aborting
[ 5.696317] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 5.702697] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 5.707198] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 5.714837] Scanning device for bad blocks
[ 5.827896] 2 cmdlinepart partitions found on MTD device orion_nand
[ 5.834195] Creating 2 MTD partitions on "orion_nand":
[ 5.839383] 0x000000000000-0x000000100000 : "u-boot"
[ 5.845570] 0x000000100000-0x000008000000 : "ubi"
[ 5.853204] libphy: Fixed MDIO Bus: probed
[ 5.858280] libphy: orion_mdio_bus: probed
[ 5.867687] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 6.975068] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address b6:d0:5e:0f:a1:17
[ 6.983923] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.990541] ehci-pci: EHCI PCI platform driver
[ 6.995088] ehci-orion: EHCI orion driver
[ 6.999303] orion-ehci f1050000.ehci: EHCI Host Controller
[ 7.004871] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 7.012721] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 7.044359] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 7.050647] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.057494] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.064775] usb usb1: Product: EHCI Host Controller
[ 7.069673] usb usb1: Manufacturer: Linux 4.11.3-kirkwood-tld-2 ehci_hcd
[ 7.076424] usb usb1: SerialNumber: f1050000.ehci
[ 7.081852] hub 1-0:1.0: USB hub found
[ 7.085720] hub 1-0:1.0: 1 port detected
[ 7.090570] mousedev: PS/2 mouse device common for all mice
[ 7.444362] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 7.636107] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 7.642852] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 7.650060] usb 1-1: Product: USB2.0 Hub
[ 7.654941] hub 1-1:1.0: USB hub found
[ 7.659108] hub 1-1:1.0: 4 ports detected
[ 7.984352] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 8.136482] usb 1-1.1: New USB device found, idVendor=13fe, idProduct=3123
[ 8.143406] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.150787] usb 1-1.1: Product: STORE N GO
[ 8.154922] usb 1-1.1: Manufacturer: Verbatim
[ 8.159298] usb 1-1.1: SerialNumber: 079917096096D074
[ 8.164404] rtc-mv f1010300.rtc: internal RTC not ticking
[ 8.164586] i2c /dev entries driver
[ 8.166057] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.166380] drop_monitor: Initializing network drop monitor service
[ 8.166622] NET: Registered protocol family 17
[ 8.166823] Key type dns_resolver registered
[ 8.167498] registered taskstats version 1
[ 8.167505] Loading compiled-in X.509 certificates
[ 8.167560] zswap: loaded using pool lzo/zbud
[ 8.198790] Key type big_key registered
[ 8.217999] Key type encrypted registered
[ 8.241072] hctosys: unable to open rtc device (rtc0)
[ 8.250020] Freeing unused kernel memory: 1024K
Loading, please wait...
[ 8.325283] systemd-udevd[111]: starting version 215
[ 8.479288] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 8.533669] scsi host0: usb-storage 1-1.1:1.0
[ 8.555755] usbcore: registered new interface driver usb-storage
[ 8.563032] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: module unknown not found in modules.dep
Begin: Checking file system ... fsck from util-linux 2.25.2
done.
mount: can't find /root in /etc/fstab
done.
Target filesystem doesn't have requested /sbin/init.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
done.
No init found. Try passing init= bootarg.
modprobe: module i8042 not found in modules.dep
[ 8.977557] uhci_hcd: USB Universal Host Controller Interface driver
[ 8.992866] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.009008] usbcore: registered new interface driver usbhid
[ 9.014852] usbhid: USB HID core driver


BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
(initramfs) [ 9.605581] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS

bleibt aber hier hängen

 

[joerg_999]

Debian gebootet, ist zwar nicht das Image von mir von der Dropbox sondern ein anderes da du hier den Kernel 4.11.3-kirkwood-tld-2 lädst, ich habe es mit 4.10.9 gemacht....
egal wenns geht
jetzt müsstest du über debian die boot envs neu flashen und dann müsstest du noch die Anpassungen für LEDE machen und deine mac adresse ändern...
bei debian aber mit fw_setenv !

wenn ich helfen soll gib Bescheid dann über Teamviewer

Nachtrag: habe gelesen es booted nicht durch wundert mich auch nicht, das ist ein Murks aus 2 Versionen....
Wenn du möchtest kann ich dir ein funktionierendes mit kernel 4.11.3-tld-2 hochladen habe es gerade gemacht und das funktioniert....

so sieht mein bootlog aus :

Spoiler: Bootlog 4.11.3-tld-2

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC:   Kirkwood 88F6281_A0
DRAM:  256 MiB
WARNING: Caches not enabled
NAND:  128 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
Hit any key to stop autoboot:  0
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
       scanning usb for storage devices...
Use USB retry period from the environment: 15 second(s)
1 Storage Device(s) found

Partition Map for USB device 0  --   Partition Type: DOS

Part    Start Sector    Num Sectors     UUID            Type
  1     2048            3993600         28c14a89-01     83 Boot

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0

## Unknown partition table type 0
loading envs from usb 0 ...
** File not found /boot/uEnv.txt **
running scan_disk ...
Scan device usb
device usb 0:1
1 bytes read in 600 ms (0 Bytes/s)
Found bootable drive on usb 0
loading uImage ...
3901632 bytes read in 816 ms (4.6 MiB/s)
loading uInitrd ...
6835537 bytes read in 827 ms (7.9 MiB/s)
loading DTB /boot/dts/kirkwood-pogo_e02.dtb ...
10444 bytes read in 3060 ms (2.9 KiB/s)
## Booting kernel from Legacy Image at 00800000 ...
   Image Name:   Linux-4.11.3-kirkwood-tld-2
   Created:      2018-04-13  20:25:47 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    3901568 Bytes = 3.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
   Image Name:   initramfs-4.11.3-kirkwood-tld-2
   Created:      2018-04-13  20:25:56 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    6835473 Bytes = 6.5 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
   Booting using the fdt blob at 0x1c00000
   Loading Kernel Image ... OK
   Loading Ramdisk to 0f48a000, end 0fb0ed11 ... OK
   Loading Device Tree to 0f484000, end 0f4898cb ... OK
Using machid 0xdd6 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.11.3-kirkwood-tld-2 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] OF: fdt: Machine model: CloudEngines Pogoplug E02
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 root=LABEL=rootfs rootdelay=10 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 239740K/262144K available (8192K kernel code, 786K rwdata, 2016K rodata, 1024K init, 280K bss, 22404K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0dc49b4   ( 787 kB)
[    0.000000]        .bss : 0xc0dc49b4 - 0xc0e0acc8   ( 281 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[    0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[    0.000492] Console: colour dummy device 80x30
[    0.000527] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090112] pid_max: default: 32768 minimum: 301
[    0.090316] Security Framework initialized
[    0.090439] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090458] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.091336] CPU: Testing write buffer coherency: ok
[    0.092369] Setting up static identity map for 0x100000 - 0x100058
[    0.092628] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[    0.096331] devtmpfs: initialized
[    0.100623] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.100651] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.100980] prandom: seed boundary self test passed
[    0.104737] prandom: 100 self tests passed
[    0.104749] pinctrl core: initialized pinctrl subsystem
[    0.105946] NET: Registered protocol family 16
[    0.106414] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.108023] cpuidle: using governor ladder
[    0.108095] cpuidle: using governor menu
[    0.108521] Feroceon L2: Enabling L2
[    0.108567] Feroceon L2: Cache support initialised.
[    0.108935] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.113578] No ATAGs?
[    0.122662] vgaarb: loaded
[    0.122978] SCSI subsystem initialized
[    0.123458] usbcore: registered new interface driver usbfs
[    0.123535] usbcore: registered new interface driver hub
[    0.123618] usbcore: registered new device driver usb
[    0.124690] clocksource: Switched to clocksource orion_clocksource
[    0.213311] VFS: Disk quotas dquot_6.6.0
[    0.213395] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.224063] NET: Registered protocol family 2
[    0.224874] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.224914] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.224945] TCP: Hash tables configured (established 2048 bind 2048)
[    0.225032] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.225056] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.225226] NET: Registered protocol family 1
[    0.225655] RPC: Registered named UNIX socket transport module.
[    0.225668] RPC: Registered udp transport module.
[    0.225676] RPC: Registered tcp transport module.
[    0.225683] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.225975] Unpacking initramfs...
[    0.845407] Freeing initrd memory: 6676K
[    0.845550] NetWinder Floating Point Emulator V0.97 (double precision)
[    0.846520] audit: initializing netlink subsys (disabled)
[    0.847004] Initialise system trusted keyrings
[    0.847136] audit: type=2000 audit(0.840:1): state=initialized audit_enabled=0 res=1
[    0.847212] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[    0.847303] zbud: loaded
[    0.848265] NFS: Registering the id_resolver key type
[    0.848293] Key type id_resolver registered
[    0.848302] Key type id_legacy registered
[    0.848320] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.848330] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.848802] Key type cifs.spnego registered
[    0.848826] Key type cifs.idmap registered
[    0.848839] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.849103] fuse init (API version 7.26)
[    0.849489] orangefs_debugfs_init: called with debug mask: :none: :0:
[    0.849756] orangefs_init: module version upstream loaded
[    0.849768] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[    2.554698] random: fast init done
[    4.967794] Key type asymmetric registered
[    4.967811] Asymmetric key parser 'x509' registered
[    4.967882] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    4.967895] io scheduler noop registered
[    4.967903] io scheduler deadline registered
[    4.967983] io scheduler cfq registered (default)
[    4.969272] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    4.971118] mv_xor f1060800.xor: Marvell shared XOR driver
[    5.025453] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    5.025675] mv_xor f1060900.xor: Marvell shared XOR driver
[    5.085433] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[    5.085864] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    5.087100] console [ttyS0] disabled
[    5.087166] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[    5.686389] console [ttyS0] enabled
[    5.698513] loop: module loaded
[    5.702833] nand: Could not find valid ONFI parameter page; aborting
[    5.709345] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[    5.715761] nand: Hynix NAND 128MiB 3,3V 8-bit
[    5.720230] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    5.727869] Scanning device for bad blocks
[    5.746952] Bad eraseblock 140 at 0x000001180000
[    5.793447] Bad eraseblock 534 at 0x0000042c0000
[    5.850135] 2 cmdlinepart partitions found on MTD device orion_nand
[    5.856447] Creating 2 MTD partitions on "orion_nand":
[    5.861611] 0x000000000000-0x000000100000 : "u-boot"
[    5.867802] 0x000000100000-0x000008000000 : "ubi"
[    5.875491] libphy: Fixed MDIO Bus: probed
[    5.880509] libphy: orion_mdio_bus: probed
[    5.889738] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    6.995373] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:90:df
[    7.004235] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    7.010843] ehci-pci: EHCI PCI platform driver
[    7.015388] ehci-orion: EHCI orion driver
[    7.019599] orion-ehci f1050000.ehci: EHCI Host Controller
[    7.025165] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    7.033016] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    7.064724] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    7.071011] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    7.077860] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.085139] usb usb1: Product: EHCI Host Controller
[    7.090038] usb usb1: Manufacturer: Linux 4.11.3-kirkwood-tld-2 ehci_hcd
[    7.096789] usb usb1: SerialNumber: f1050000.ehci
[    7.102214] hub 1-0:1.0: USB hub found
[    7.106083] hub 1-0:1.0: 1 port detected
[    7.110915] mousedev: PS/2 mouse device common for all mice
[    7.464725] usb 1-1: new high-speed USB device number 2 using orion-ehci
[    7.656402] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    7.663148] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    7.670355] usb 1-1: Product: USB2.0 Hub
[    7.675235] hub 1-1:1.0: USB hub found
[    7.679402] hub 1-1:1.0: 4 ports detected
[    8.004728] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[    8.155899] usb 1-1.4: New USB device found, idVendor=0781, idProduct=5583
[    8.162821] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    8.170214] rtc-mv f1010300.rtc: internal RTC not ticking
[    8.170398] i2c /dev entries driver
[    8.171869] hidraw: raw HID events driver (C) Jiri Kosina
[    8.172192] drop_monitor: Initializing network drop monitor service
[    8.172433] NET: Registered protocol family 17
[    8.172611] Key type dns_resolver registered
[    8.173329] registered taskstats version 1
[    8.173336] Loading compiled-in X.509 certificates
[    8.173391] zswap: loaded using pool lzo/zbud
[    8.198544] Key type big_key registered
[    8.228089] Key type encrypted registered
[    8.246310] usb 1-1.4: Product: Ultra Fit
[    8.250338] usb 1-1.4: Manufacturer: SanDisk
[    8.254628] usb 1-1.4: SerialNumber: 4C530001320908104320
[    8.260827] hctosys: unable to open rtc device (rtc0)
[    8.269731] Freeing unused kernel memory: 1024K
Loading, please wait...
[    8.346748] systemd-udevd[112]: starting version 215
[    8.511101] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    8.577260] scsi host0: usb-storage 1-1.4:1.0
[    8.588530] usbcore: registered new interface driver usb-storage
[    8.615941] usbcore: registered new interface driver uas
[    9.605875] scsi 0:0:0:0: Direct-Access     SanDisk  Ultra Fit        1.00 PQ: 0 ANSI: 6
[    9.621593] sd 0:0:0:0: [sda] 60062500 512-byte logical blocks: (30.8 GB/28.6 GiB)
[    9.632448] sd 0:0:0:0: [sda] Write Protect is off
[    9.638058] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[    9.654864]  sda: sda1
[    9.660810] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    9.670191] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: module ext3 not found in modules.dep
Begin: Will now check root file system ... fsck from util-linux 2.25.2
fsck: error 2 (No such file or directory) while executing fsck.ext3 for /dev/sda1
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[   23.925863] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
[   23.943770] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[   25.293571] systemd-udevd[310]: starting version 215
. ok
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[   25.796124] orion_wdt: Initial timeout 21 sec
[   25.910669] marvell-cesa f1030000.crypto: CESA device successfully registered
done.
[ ok ] Activating swap...done.
[   26.817826] EXT4-fs (sda1): re-mounted. Opts: (null)
[....] Checking root file system...fsck from util-linux 2.25.2
rootfs: clean, 20714/124928 files, 184091/499200 blocks
done.
[   27.007873] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.25.2
done.
[ ok ] Loading kernel modules...done.
[ ok ] Cleaning up temporary files... /tmp.
[   28.422077] random: crng init done
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
[ ok ] Setting kernel variables ...done.
[   29.711320] NET: Registered protocol family 10
[   29.716976] Segment Routing with IPv6
[   30.908281] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1
Copyright 2004-2014 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

Listening on LPF/eth0/00:25:31:04:90:df
Sending on   LPF/eth0/00:25:31:04:90:df
Sending on   Socket/fallback
DHCPREQUEST on eth0 to 255.255.255.255 port 67
[   33.354009] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   33.363937] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.5.1
bound to 192.168.5.110 -- renewal in 5087 seconds.
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting busybox' syslogd implementation : syslogdStarting /sbin/syslogd...
1258 (syslogd)
. ok
[ ok ] Starting system message bus: dbus.
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon.
[warn] Not starting NFS kernel daemon: no exports. ... (warning).
[ ok ] Starting NTP server: ntpd.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[....] Starting busybox' klogd implementation : klogdStarting /sbin/klogd...
1256 (klogd)
. ok

Debian GNU/Linux 8 debian ttyS0

debian login: root
Password:
Last login: Fri Apr 13 22:50:27 CEST 2018 on ttyS0
Linux debian 4.11.3-kirkwood-tld-2 #1 PREEMPT Tue Jun 6 17:01:17 PDT 2017 armv5tel

 

[nuggelbeb]

OK, ich mache den Stick noch einmal. War heute zu viel für mich.
Die richtige MAC ist 00:25:31:04:979
Melde mich gleich über PN

Spoiler: NEU

U-Boot 2017.07-tld-1 (Sep 05 2017 - 00:13:18 -0700)
Pogo E02

SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
Hit any key to stop autoboot: 0
PogoE02> setenv load_dtb 'ext2load usb 0:1 0x1c00000 /boot/dts/kirkwood-pogo_e02.dtb'
PogoE02> setenv load_initrd 'ext2load usb 0:1 0x1100000 /boot/uInitrd'
PogoE02> setenv load_uimage 'ext2load usb 0:1 0x800000 /boot/uImage'
PogoE02> setenv usb_boot 'run load_dtb; run load_uimage; if run load_initrd; then bootm 0x800000 0x1100000 0x1c00000; else bootm 0x800000 - 0x1c00000; fi'
PogoE02> usb reset; run usb_boot
resetting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 3 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
10444 bytes read in 2998 ms (2.9 KiB/s)
3414304 bytes read in 743 ms (4.4 MiB/s)
7290654 bytes read in 806 ms (8.6 MiB/s)
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-4.10.9-kirkwood-tld-1
Created: 2018-04-13 19:17:57 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3414240 Bytes = 3.3 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-4.10.9-kirkwood-tld-1
Created: 2018-04-13 19:18:08 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 7290590 Bytes = 7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01c00000
Booting using the fdt blob at 0x1c00000
Loading Kernel Image ... OK
Loading Ramdisk to 0f41b000, end 0fb0eede ... OK
Loading Device Tree to 0f415000, end 0f41a8cb ... OK
Using machid 0xdd6 from environment

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.10.9-kirkwood-tld-1 (root@tldDebian) (gcc version 4.9.2 (Debian 4.9.2-10) ) #1 PREEMPT Sun Apr 9 23:40:29 PDT 2017
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt:Machine model: CloudEngines Pogoplug E02
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:0x100000@0x0(u-boot),-@0x100000(ubi)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 242848K/262144K available (6489K kernel code, 654K rwdata, 1800K rodata, 320K init, 325K bss, 19296K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc065e808 (6491 kB)
[ 0.000000] .init : 0xc0856000 - 0xc08a6000 ( 320 kB)
[ 0.000000] .data : 0xc08a6000 - 0xc094984c ( 655 kB)
[ 0.000000] .bss : 0xc094984c - 0xc099af20 ( 326 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9556302233 ns
[ 0.000008] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 10737418237ns
[ 0.000528] Console: colour dummy device 80x30
[ 0.000563] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 0.090111] pid_max: default: 32768 minimum: 301
[ 0.090347] Security Framework initialized
[ 0.090484] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090503] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.091597] CPU: Testing write buffer coherency: ok
[ 0.092533] Setting up static identity map for 0x8200 - 0x8258
[ 0.092789] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x2
[ 0.096087] devtmpfs: initialized
[ 0.100020] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.100107] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.100398] prandom: seed boundary self test passed
[ 0.104152] prandom: 100 self tests passed
[ 0.104163] pinctrl core: initialized pinctrl subsystem
[ 0.105355] NET: Registered protocol family 16
[ 0.105766] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.130106] cpuidle: using governor ladder
[ 0.160104] cpuidle: using governor menu
[ 0.160476] Feroceon L2: Enabling L2
[ 0.160521] Feroceon L2: Cache support initialised.
[ 0.160901] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[ 0.165605] No ATAGs?
[ 0.201597] vgaarb: loaded
[ 0.201906] SCSI subsystem initialized
[ 0.202362] usbcore: registered new interface driver usbfs
[ 0.202434] usbcore: registered new interface driver hub
[ 0.202512] usbcore: registered new device driver usb
[ 0.203495] clocksource: Switched to clocksource orion_clocksource
[ 0.250259] VFS: Disk quotas dquot_6.6.0
[ 0.250345] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.260894] NET: Registered protocol family 2
[ 0.261740] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.261778] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.261809] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.261877] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.261900] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.262072] NET: Registered protocol family 1
[ 0.262561] RPC: Registered named UNIX socket transport module.
[ 0.262572] RPC: Registered udp transport module.
[ 0.262579] RPC: Registered tcp transport module.
[ 0.262586] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.262871] Unpacking initramfs...
[ 0.933872] Freeing initrd memory: 7120K
[ 0.933965] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.934936] audit: initializing netlink subsys (disabled)
[ 0.935405] Initialise system trusted keyrings
[ 0.935605] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 0.935700] zbud: loaded
[ 0.936722] NFS: Registering the id_resolver key type
[ 0.936753] Key type id_resolver registered
[ 0.936761] Key type id_legacy registered
[ 0.936778] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.936788] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.937017] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.937391] orangefs_debugfs_init: called with debug mask: :none: :0:
[ 0.937644] orangefs_init: module version upstream loaded
[ 2.553502] random: fast init done
[ 5.052124] Key type asymmetric registered
[ 5.052140] Asymmetric key parser 'x509' registered
[ 5.052224] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 5.052235] io scheduler noop registered
[ 5.052243] io scheduler deadline registered
[ 5.052275] io scheduler cfq registered (default)
[ 5.053798] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[ 5.055592] mv_xor f1060800.xor: Marvell shared XOR driver
[ 5.114241] mv_xor f1060800.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[ 5.114469] mv_xor f1060900.xor: Marvell shared XOR driver
[ 5.174240] mv_xor f1060900.xor: Marvell XOR (Registers Mode): ( xor cpy sg intr )
[ 5.174703] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 5.175906] console [ttyS0] disabled
[ 5.175971] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 25, base_baud = 12500000) is a 16550A
[ 5.744657] console [ttyS0] enabled
[ 5.749705] nand: Could not find valid ONFI parameter page; aborting
[ 5.756166] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xf1
[ 5.762547] nand: Hynix NAND 128MiB 3,3V 8-bit
[ 5.767034] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 5.774661] Scanning device for bad blocks
[ 5.887704] 2 cmdlinepart partitions found on MTD device orion_nand
[ 5.894022] Creating 2 MTD partitions on "orion_nand":
[ 5.899196] 0x000000000000-0x000000100000 : "u-boot"
[ 5.905472] 0x000000100000-0x000008000000 : "ubi"
[ 5.913123] libphy: Fixed MDIO Bus: probed
[ 5.918146] libphy: orion_mdio_bus: probed
[ 5.927694] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 7.034237] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address b6:d0:5e:0f:a1:17
[ 7.043094] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 7.049712] ehci-pci: EHCI PCI platform driver
[ 7.054254] ehci-orion: EHCI orion driver
[ 7.058453] orion-ehci f1050000.ehci: EHCI Host Controller
[ 7.064022] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[ 7.071868] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[ 7.103529] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[ 7.109818] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 7.116665] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.123945] usb usb1: Product: EHCI Host Controller
[ 7.128844] usb usb1: Manufacturer: Linux 4.10.9-kirkwood-tld-1 ehci_hcd
[ 7.135593] usb usb1: SerialNumber: f1050000.ehci
[ 7.141053] hub 1-0:1.0: USB hub found
[ 7.144919] hub 1-0:1.0: 1 port detected
[ 7.149717] mousedev: PS/2 mouse device common for all mice
[ 7.503528] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 7.695125] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 7.701875] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 7.709082] usb 1-1: Product: USB2.0 Hub
[ 7.713829] hub 1-1:1.0: USB hub found
[ 7.718000] hub 1-1:1.0: 4 ports detected
[ 8.043522] usb 1-1.1: new high-speed USB device number 3 using orion-ehci
[ 8.195627] usb 1-1.1: New USB device found, idVendor=13fe, idProduct=3123
[ 8.202551] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 8.209932] usb 1-1.1: Product: STORE N GO
[ 8.214066] usb 1-1.1: Manufacturer: Verbatim
[ 8.218442] usb 1-1.1: SerialNumber: 079917096096D074
[ 8.243523] rtc-mv f1010300.rtc: internal RTC not ticking
[ 8.249123] i2c /dev entries driver
[ 8.253746] hidraw: raw HID events driver (C) Jiri Kosina
[ 8.259507] drop_monitor: Initializing network drop monitor service
[ 8.266073] NET: Registered protocol family 17
[ 8.270714] Key type dns_resolver registered
[ 8.275761] registered taskstats version 1
[ 8.279874] Loading compiled-in X.509 certificates
[ 8.284769] zswap: loaded using pool lzo/zbud
[ 8.299988] Key type big_key registered
[ 8.314255] Key type encrypted registered
[ 8.319619] hctosys: unable to open rtc device (rtc0)
[ 8.326143] Freeing unused kernel memory: 320K
[ 8.330605] This architecture does not have kernel memory protection.
Loading, please wait...
[ 8.414463] systemd-udevd[93]: starting version 215
[ 8.571049] usb-storage 1-1.1:1.0: USB Mass Storage device detected
[ 8.624798] scsi host0: usb-storage 1-1.1:1.0
[ 8.638904] usbcore: registered new interface driver usb-storage
[ 8.667184] usbcore: registered new interface driver uas
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
modprobe: module unknown not found in modules.dep
Begin: Will now check file system ... fsck from util-linux 2.25.2
Checking all file systems.
done.
mount: can't find /root in /etc/fstab
done.
Target filesystem doesn't have requested /sbin/init.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... mount: mounting /dev on /root/dev failed: No such file or directory
done.
No init found. Try passing init= bootarg.
modprobe: module i8042 not found in modules.dep
[ 9.017699] uhci_hcd: USB Universal Host Controller Interface driver
[ 9.033014] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 9.049341] usbcore: registered new interface driver usbhid
[ 9.055143] usbhid: USB HID core driver


BusyBox v1.22.1 (Debian 1:1.22.0-9+deb8u1) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/bin/sh: can't access tty; job control turned off
(initramfs) [ 9.684848] scsi 0:0:0:0: Direct-Access Verbatim STORE N GO 5.00 PQ: 0 ANSI: 0 CCS