D
Deleted member 130877
Guest
Hallo Leute,
ich brauche eure Hilfe.
Meine Pogo startet nicht mehr von alleine.
Hab mir ein TTL Kabel besorgt und angeschlossen:
Und nach dieser Anleitung bin ich nun mit der Pogo Verbunden:
Das wird angezeigt
und
u-boot>> printenv
Wie muss ich jetzt weitermachen damit ich wieder Debian drauf installieren kann?
Das kennt er nicht:
u-boot>> wget
Unknown command 'wget' - try 'help'
edit:
Konnte nun Linux starten mit diesem Image:
Link ist nicht mehr aktiv.
Die Pogo kan immernoch keine Netzwerkverbindung herstellen:
Wie bekomme ich das Netzwerk aktiviert oder kann ich den Uboot auch offline installieren?
Damit ich das hier ausführen kann:
edit:
Wenn ich das Netzwerk neustarten will, kommt folgender Fehler:
ich brauche eure Hilfe.
Meine Pogo startet nicht mehr von alleine.
Hab mir ein TTL Kabel besorgt und angeschlossen:
Sie müssen registriert sein, um Links zu sehen.
Und nach dieser Anleitung bin ich nun mit der Pogo Verbunden:
Sie müssen registriert sein, um Links zu sehen.
Das wird angezeigt
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
reading /rescueme.txt
0 bytes read
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
u-boot>>
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
reading /rescueme.txt
0 bytes read
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
u-boot>>
u-boot>> printenv
u-boot>> printenvarcNumber=3542
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:04:9C:75
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
Environment size: 2355/131068 bytes
u-boot>>
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:04:9C:75
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params
Environment size: 2355/131068 bytes
u-boot>>
Das kennt er nicht:
u-boot>> wget
Sie müssen registriert sein, um Links zu sehen.
Unknown command 'wget' - try 'help'
edit:
Konnte nun Linux starten mit diesem Image:
Link ist nicht mehr aktiv.
Die Pogo kan immernoch keine Netzwerkverbindung herstellen:
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)Pogoplug E02
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2221032 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
5962267 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.11.1-kirkwood-tld-2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2220968 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.11.1-kirkwood-tld-2
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5962203 Bytes = 5.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Using machid 0xdd6 from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.1-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Sun Oct 6 17:06:02 PDT 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug E02
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 247512K/262144K available (4192K kernel code, 309K rwdata, 1368K rodata, 187K init, 420K bss, 14632K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc057622c (5561 kB)
[ 0.000000] .init : 0xc0577000 - 0xc05a5da4 ( 188 kB)
[ 0.000000] .data : 0xc05a6000 - 0xc05f3618 ( 310 kB)
[ 0.000000] .bss : 0xc05f3618 - 0xc065c6ac ( 421 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 9.995006] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 10.084797] pid_max: default: 32768 minimum: 301
[ 10.084899] Security Framework initialized
[ 10.084969] Mount-cache hash table entries: 512
[ 10.085580] Initializing cgroup subsys devices
[ 10.085603] Initializing cgroup subsys freezer
[ 10.085615] Initializing cgroup subsys net_cls
[ 10.085626] Initializing cgroup subsys blkio
[ 10.085703] CPU: Testing write buffer coherency: ok
[ 10.086091] Setting up static identity map for 0xc03f7248 - 0xc03f7284
[ 10.087938] devtmpfs: initialized
[ 10.090180] pinctrl core: initialized pinctrl subsystem
[ 10.090507] regulator-dummy: no parameters
[ 10.090824] NET: Registered protocol family 16
[ 10.091243] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 10.091998] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 10.092019] Feroceon L2: Enabling L2
[ 10.092058] Feroceon L2: Cache support initialised.
[ 10.095861] bio: create slab <bio-0> at 0
[ 10.096293] vgaarb: loaded
[ 10.096420] usbcore: registered new interface driver usbfs
[ 10.096481] usbcore: registered new interface driver hub
[ 10.096577] usbcore: registered new device driver usb
[ 10.097194] Switched to clocksource orion_clocksource
[ 10.111613] NET: Registered protocol family 2
[ 10.112247] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 10.112304] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 10.112336] TCP: Hash tables configured (established 2048 bind 2048)
[ 10.112402] TCP: reno registered
[ 10.112416] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 10.112439] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 10.112638] NET: Registered protocol family 1
[ 10.112955] RPC: Registered named UNIX socket transport module.
[ 10.112966] RPC: Registered udp transport module.
[ 10.112973] RPC: Registered tcp transport module.
[ 10.112980] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.113195] Unpacking initramfs...
[ 10.617726] Freeing initrd memory: 5816K (c1101000 - c16af000)
[ 10.617827] NetWinder Floating Point Emulator V0.97 (double precision)
[ 10.618432] audit: initializing netlink socket (disabled)
[ 10.618479] type=2000 audit(0.620:1): initialized
[ 10.619325] VFS: Disk quotas dquot_6.5.2
[ 10.619376] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 10.619737] NFS: Registering the id_resolver key type
[ 10.619795] Key type id_resolver registered
[ 10.619805] Key type id_legacy registered
[ 10.619824] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 10.619979] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 10.620193] msgmni has been set to 494
[ 10.622069] alg: No test for stdrng (krng)
[ 10.622163] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 10.622175] io scheduler noop registered
[ 10.622183] io scheduler deadline registered
[ 10.622205] io scheduler cfq registered (default)
[ 10.622400] mv_xor mv_xor.0: Marvell shared XOR driver
[ 10.657274] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.697252] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.697353] mv_xor mv_xor.1: Marvell shared XOR driver
[ 10.737251] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.777251] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.777510] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 10.798055] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 11.294311] console [ttyS0] enabled
[ 11.298945] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 11.310854] Scanning device for bad blocks
[ 11.319537] Bad eraseblock 43 at 0x000000560000
[ 11.426648] 4 cmdlinepart partitions found on MTD device orion_nand
[ 11.432954] Creating 4 MTD partitions on "orion_nand":
[ 11.438130] 0x000000000000-0x000000100000 : "u-boot"
[ 11.443354] 0x000000100000-0x000000500000 : "uImage"
[ 11.448561] 0x000000500000-0x000002500000 : "rootfs"
[ 11.453797] 0x000002500000-0x000008000000 : "data"
[ 11.458983] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.465542] ehci-pci: EHCI PCI platform driver
[ 11.470070] ehci-orion: EHCI orion driver
[ 11.474147] orion-ehci orion-ehci.0: EHCI Host Controller
[ 11.479605] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 11.487411] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 11.507229] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 11.513250] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.520093] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.527368] usb usb1: Product: EHCI Host Controller
[ 11.532271] usb usb1: Manufacturer: Linux 3.11.1-kirkwood-tld-2 ehci_hcd
[ 11.539017] usb usb1: SerialNumber: orion-ehci.0
[ 11.544064] hub 1-0:1.0: USB hub found
[ 11.547883] hub 1-0:1.0: 1 port detected
[ 11.552245] mousedev: PS/2 mouse device common for all mice
[ 11.867230] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 12.018673] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 12.025416] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 12.032609] usb 1-1: Product: USB2.0 Hub
[ 12.037145] hub 1-1:1.0: USB hub found
[ 12.041299] hub 1-1:1.0: 4 ports detected
[ 12.327549] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 12.440547] usb 1-1.4: New USB device found, idVendor=13fe, idProduct=3e00
[ 12.447475] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 12.454837] usb 1-1.4: Product: USBee
[ 12.458534] usb 1-1.4: Manufacturer: Terra
[ 12.462651] usb 1-1.4: SerialNumber: 07084285611C7493
[ 12.567221] rtc-mv rtc-mv: internal RTC not ticking
[ 12.572224] i2c /dev entries driver
[ 12.575807] cpuidle: using governor ladder
[ 12.579945] cpuidle: using governor menu
[ 12.584298] drop_monitor: Initializing network drop monitor service
[ 12.590900] TCP: cubic registered
[ 12.594236] NET: Registered protocol family 17
[ 12.598832] Key type dns_resolver registered
[ 12.603536] registered taskstats version 1
[ 12.608502] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 12.615605] Freeing unused kernel memory: 184K (c0577000 - c05a5000)
Loading, please wait...
[ 12.677870] udevd[52]: starting version 175
[ 12.745539] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 12.860603] libphy: orion_mdio_bus: probed
[ 12.888581] SCSI subsystem initialized
[ 12.926654] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 12.979285] scsi0 : usb-storage 1-1.4:1.0
[ 12.999934] usbcore: registered new interface driver usb-storage
[ 13.978398] scsi 0:0:0:0: Direct-Access Terra USBee PMAP PQ: 0 ANSI: 4
[ 14.028361] sd 0:0:0:0: [sda] 3913728 512-byte logical blocks: (2.00 GB/1.86 GiB)
[ 14.047279] sd 0:0:0:0: [sda] Write Protect is off
[ 14.053076] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.067212] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.083649] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:9c:75
[ 14.095236] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.103820] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.112071] sda: sda1 sda2
[ 14.119202] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.124731] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.130917] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 14.146630] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 24.437413] EXT3-fs (sda1): mounted filesystem with ordered data mode
Begin: Running /[ 24.445404] kjournald starting. Commit interval 5 seconds
scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 25.487908] udevd[238]: starting version 175
udevd[238]: specified group 'pcscd' unknown
. ok
udevd[238]: specified group 'pcscd' unknown
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 25.907507] alg: hash: Test 1 failed for mv-hmac-sha1
[ 25.912591] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[ 25.927030] 00000010: b7 c3 16 0c
[ 25.967581] orion_wdt: Initial timeout 21 sec
done.
[....] Activating swap...[ 26.949734] Adding 490104k swap on /dev/sda2. Priority:-1 extents:1 across:490104k
done.
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/sda1: clean, 27736/91776 files, 185038/366613 blocks
done.
[ 27.263635] EXT3-fs (sda1): using internal journal
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
udevd[238]: specified group 'pcscd' unknown
[ ok ] Setting kernel variables ...done.
[....] Configuring network interfaces...err, eth0: ioctl SIOCGIFHWADDR: No such device
Failed to bring up eth0.
[ ok [ 31.298280] NET: Registered protocol family 10
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[info] Setting console screen modes and fonts.
setterm: cannot (un)set powersave mode: Inappropriate ioctl for device
[....] Setting sensors limitsNo sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
. ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting rpcbind daemon...[....] Already running..
[ ok ] Starting enhanced syslogd: rsyslogd.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting web server: apache2(2)No such file or directory: apache2: could not open error log file /var/log/apache2/error.log.
Unable to open logs
Action 'start' failed.
The Apache error log may have more information.
failed!
*** Starting tmpfs file restore: varlog.
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[FAIL] startpar: service(s) returned failure: apache2 ... failed!
OScam : gestartet
grep: /tmp/.oscam/oscam.version: No such file or directory
Debian GNU/Linux 7 debian ttyS0
debian login: root
Password:
Last login: Sat Nov 2 22:06:59 CET 2013 on ttyS0
Linux debian 3.11.1-kirkwood-tld-2 #1 PREEMPT Sun Oct 6 17:06:02 PDT 2013 armv5tel
Willkommen am Debian CS-Server IPC
IPC Befehle : ipc : i
CCcam Befehle : cccam : c
OScam Befehle : oscam : o
NewCS Befehle : newcs : n
Camd3 Befehle : camd3 : c3
sBox Befehle : sbox : s
root@debian ~ > killall hbwd
hbwd: no process found
root@debian ~ > cd /tmp
root@debian /tmp > wget
--1970-01-01 01:01:01--
Resolving projects.doozan.com (projects.doozan.com)... failed: Name or service not known.
wget: unable to resolve host address `projects.doozan.com'
root@debian /tmp > chmod +x install_uboot_mtd0.sh
chmod: cannot access `install_uboot_mtd0.sh': No such file or directory
root@debian /tmp > ./install_uboot_mtd0.sh
-bash: ./install_uboot_mtd0.sh: No such file or directory
root@debian /tmp > ping 192.168.1.1
connect: Network is unreachable
root@debian /tmp >
SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
** File not found /rescueme
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
1 bytes read
Found bootable drive on usb 0:1
Loading file "/boot/uImage" from usb device 0:1 (usbda1)
2221032 bytes read
Loading file "/boot/uInitrd" from usb device 0:1 (usbda1)
5962267 bytes read
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux-3.11.1-kirkwood-tld-2
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2220968 Bytes = 2.1 MiB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 01100000 ...
Image Name: initramfs-3.11.1-kirkwood-tld-2
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5962203 Bytes = 5.7 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Using machid 0xdd6 from environment
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.1-kirkwood-tld-2 (root@tldDebian) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 PREEMPT Sun Oct 6 17:06:02 PDT 2013
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: Pogoplug E02
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda1 rootdelay=10 rootfstype=ext3 mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 247512K/262144K available (4192K kernel code, 309K rwdata, 1368K rodata, 187K init, 420K bss, 14632K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc057622c (5561 kB)
[ 0.000000] .init : 0xc0577000 - 0xc05a5da4 ( 188 kB)
[ 0.000000] .data : 0xc05a6000 - 0xc05f3618 ( 310 kB)
[ 0.000000] .bss : 0xc05f3618 - 0xc065c6ac ( 421 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:114
[ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[ 0.000000] Console: colour dummy device 80x30
[ 9.995006] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[ 10.084797] pid_max: default: 32768 minimum: 301
[ 10.084899] Security Framework initialized
[ 10.084969] Mount-cache hash table entries: 512
[ 10.085580] Initializing cgroup subsys devices
[ 10.085603] Initializing cgroup subsys freezer
[ 10.085615] Initializing cgroup subsys net_cls
[ 10.085626] Initializing cgroup subsys blkio
[ 10.085703] CPU: Testing write buffer coherency: ok
[ 10.086091] Setting up static identity map for 0xc03f7248 - 0xc03f7284
[ 10.087938] devtmpfs: initialized
[ 10.090180] pinctrl core: initialized pinctrl subsystem
[ 10.090507] regulator-dummy: no parameters
[ 10.090824] NET: Registered protocol family 16
[ 10.091243] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 10.091998] Kirkwood: MV88F6281-A0, TCLK=200000000.
[ 10.092019] Feroceon L2: Enabling L2
[ 10.092058] Feroceon L2: Cache support initialised.
[ 10.095861] bio: create slab <bio-0> at 0
[ 10.096293] vgaarb: loaded
[ 10.096420] usbcore: registered new interface driver usbfs
[ 10.096481] usbcore: registered new interface driver hub
[ 10.096577] usbcore: registered new device driver usb
[ 10.097194] Switched to clocksource orion_clocksource
[ 10.111613] NET: Registered protocol family 2
[ 10.112247] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 10.112304] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 10.112336] TCP: Hash tables configured (established 2048 bind 2048)
[ 10.112402] TCP: reno registered
[ 10.112416] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 10.112439] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 10.112638] NET: Registered protocol family 1
[ 10.112955] RPC: Registered named UNIX socket transport module.
[ 10.112966] RPC: Registered udp transport module.
[ 10.112973] RPC: Registered tcp transport module.
[ 10.112980] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.113195] Unpacking initramfs...
[ 10.617726] Freeing initrd memory: 5816K (c1101000 - c16af000)
[ 10.617827] NetWinder Floating Point Emulator V0.97 (double precision)
[ 10.618432] audit: initializing netlink socket (disabled)
[ 10.618479] type=2000 audit(0.620:1): initialized
[ 10.619325] VFS: Disk quotas dquot_6.5.2
[ 10.619376] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 10.619737] NFS: Registering the id_resolver key type
[ 10.619795] Key type id_resolver registered
[ 10.619805] Key type id_legacy registered
[ 10.619824] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 10.619979] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 10.620193] msgmni has been set to 494
[ 10.622069] alg: No test for stdrng (krng)
[ 10.622163] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 10.622175] io scheduler noop registered
[ 10.622183] io scheduler deadline registered
[ 10.622205] io scheduler cfq registered (default)
[ 10.622400] mv_xor mv_xor.0: Marvell shared XOR driver
[ 10.657274] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.697252] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 10.697353] mv_xor mv_xor.1: Marvell shared XOR driver
[ 10.737251] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.777251] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 10.777510] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 10.798055] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 11.294311] console [ttyS0] enabled
[ 11.298945] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
[ 11.310854] Scanning device for bad blocks
[ 11.319537] Bad eraseblock 43 at 0x000000560000
[ 11.426648] 4 cmdlinepart partitions found on MTD device orion_nand
[ 11.432954] Creating 4 MTD partitions on "orion_nand":
[ 11.438130] 0x000000000000-0x000000100000 : "u-boot"
[ 11.443354] 0x000000100000-0x000000500000 : "uImage"
[ 11.448561] 0x000000500000-0x000002500000 : "rootfs"
[ 11.453797] 0x000002500000-0x000008000000 : "data"
[ 11.458983] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.465542] ehci-pci: EHCI PCI platform driver
[ 11.470070] ehci-orion: EHCI orion driver
[ 11.474147] orion-ehci orion-ehci.0: EHCI Host Controller
[ 11.479605] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 11.487411] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 11.507229] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 11.513250] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.520093] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 11.527368] usb usb1: Product: EHCI Host Controller
[ 11.532271] usb usb1: Manufacturer: Linux 3.11.1-kirkwood-tld-2 ehci_hcd
[ 11.539017] usb usb1: SerialNumber: orion-ehci.0
[ 11.544064] hub 1-0:1.0: USB hub found
[ 11.547883] hub 1-0:1.0: 1 port detected
[ 11.552245] mousedev: PS/2 mouse device common for all mice
[ 11.867230] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 12.018673] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[ 12.025416] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 12.032609] usb 1-1: Product: USB2.0 Hub
[ 12.037145] hub 1-1:1.0: USB hub found
[ 12.041299] hub 1-1:1.0: 4 ports detected
[ 12.327549] usb 1-1.4: new high-speed USB device number 3 using orion-ehci
[ 12.440547] usb 1-1.4: New USB device found, idVendor=13fe, idProduct=3e00
[ 12.447475] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 12.454837] usb 1-1.4: Product: USBee
[ 12.458534] usb 1-1.4: Manufacturer: Terra
[ 12.462651] usb 1-1.4: SerialNumber: 07084285611C7493
[ 12.567221] rtc-mv rtc-mv: internal RTC not ticking
[ 12.572224] i2c /dev entries driver
[ 12.575807] cpuidle: using governor ladder
[ 12.579945] cpuidle: using governor menu
[ 12.584298] drop_monitor: Initializing network drop monitor service
[ 12.590900] TCP: cubic registered
[ 12.594236] NET: Registered protocol family 17
[ 12.598832] Key type dns_resolver registered
[ 12.603536] registered taskstats version 1
[ 12.608502] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 12.615605] Freeing unused kernel memory: 184K (c0577000 - c05a5000)
Loading, please wait...
[ 12.677870] udevd[52]: starting version 175
[ 12.745539] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 12.860603] libphy: orion_mdio_bus: probed
[ 12.888581] SCSI subsystem initialized
[ 12.926654] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 12.979285] scsi0 : usb-storage 1-1.4:1.0
[ 12.999934] usbcore: registered new interface driver usb-storage
[ 13.978398] scsi 0:0:0:0: Direct-Access Terra USBee PMAP PQ: 0 ANSI: 4
[ 14.028361] sd 0:0:0:0: [sda] 3913728 512-byte logical blocks: (2.00 GB/1.86 GiB)
[ 14.047279] sd 0:0:0:0: [sda] Write Protect is off
[ 14.053076] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.067212] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.083649] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:25:31:04:9c:75
[ 14.095236] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.103820] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.112071] sda: sda1 sda2
[ 14.119202] sd 0:0:0:0: [sda] No Caching mode page present
[ 14.124731] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 14.130917] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 14.146630] sd 0:0:0:0: Attached scsi generic sg0 type 0
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[ 24.437413] EXT3-fs (sda1): mounted filesystem with ordered data mode
Begin: Running /[ 24.445404] kjournald starting. Commit interval 5 seconds
scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... done.
INIT: version 2.88 booting
[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevd[ 25.487908] udevd[238]: starting version 175
udevd[238]: specified group 'pcscd' unknown
. ok
udevd[238]: specified group 'pcscd' unknown
[ ok ] Synthesizing the initial hotplug events...done.
[....] Waiting for /dev to be fully populated...[ 25.907507] alg: hash: Test 1 failed for mv-hmac-sha1
[ 25.912591] 00000000: 0c aa 9f d5 37 c3 79 3a 91 d9 21 5f 42 2b 2c 24
[ 25.927030] 00000010: b7 c3 16 0c
[ 25.967581] orion_wdt: Initial timeout 21 sec
done.
[....] Activating swap...[ 26.949734] Adding 490104k swap on /dev/sda2. Priority:-1 extents:1 across:490104k
done.
[....] Checking root file system...fsck from util-linux 2.20.1
/dev/sda1: clean, 27736/91776 files, 185038/366613 blocks
done.
[ 27.263635] EXT3-fs (sda1): using internal journal
[ ok ] Cleaning up temporary files... /tmp.
[ ok ] Activating lvm and md swap...done.
[....] Checking file systems...fsck from util-linux 2.20.1
done.
[ ok ] Mounting local filesystems...done.
[ ok ] Activating swapfile swap...done.
[ ok ] Cleaning up temporary files....
udevd[238]: specified group 'pcscd' unknown
[ ok ] Setting kernel variables ...done.
[....] Configuring network interfaces...err, eth0: ioctl SIOCGIFHWADDR: No such device
Failed to bring up eth0.
[ ok [ 31.298280] NET: Registered protocol family 10
done.
[ ok ] Starting rpcbind daemon....
[ ok ] Starting NFS common utilities: statd idmapd.
[ ok ] Cleaning up temporary files....
[info] Setting console screen modes and fonts.
setterm: cannot (un)set powersave mode: Inappropriate ioctl for device
[....] Setting sensors limitsNo sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
No sensors found!
Make sure you loaded all the kernel drivers you need.
Try sensors-detect to find out which these are.
. ok
INIT: Entering runlevel: 2
[info] Using makefile-style concurrent boot in runlevel 2.
[ ok ] Starting rpcbind daemon...[....] Already running..
[ ok ] Starting enhanced syslogd: rsyslogd.
[ ok ] Starting NFS common utilities: statd idmapd.
[....] Starting web server: apache2(2)No such file or directory: apache2: could not open error log file /var/log/apache2/error.log.
Unable to open logs
Action 'start' failed.
The Apache error log may have more information.
failed!
*** Starting tmpfs file restore: varlog.
[ ok ] Starting periodic command scheduler: cron.
[ ok ] Starting OpenBSD Secure Shell server: sshd.
[FAIL] startpar: service(s) returned failure: apache2 ... failed!
OScam : gestartet
grep: /tmp/.oscam/oscam.version: No such file or directory
Debian GNU/Linux 7 debian ttyS0
debian login: root
Password:
Last login: Sat Nov 2 22:06:59 CET 2013 on ttyS0
Linux debian 3.11.1-kirkwood-tld-2 #1 PREEMPT Sun Oct 6 17:06:02 PDT 2013 armv5tel
Willkommen am Debian CS-Server IPC
IPC Befehle : ipc : i
CCcam Befehle : cccam : c
OScam Befehle : oscam : o
NewCS Befehle : newcs : n
Camd3 Befehle : camd3 : c3
sBox Befehle : sbox : s
root@debian ~ > killall hbwd
hbwd: no process found
root@debian ~ > cd /tmp
root@debian /tmp > wget
Sie müssen registriert sein, um Links zu sehen.
--1970-01-01 01:01:01--
Sie müssen registriert sein, um Links zu sehen.
Resolving projects.doozan.com (projects.doozan.com)... failed: Name or service not known.
wget: unable to resolve host address `projects.doozan.com'
root@debian /tmp > chmod +x install_uboot_mtd0.sh
chmod: cannot access `install_uboot_mtd0.sh': No such file or directory
root@debian /tmp > ./install_uboot_mtd0.sh
-bash: ./install_uboot_mtd0.sh: No such file or directory
root@debian /tmp > ping 192.168.1.1
connect: Network is unreachable
root@debian /tmp >
Damit ich das hier ausführen kann:
Code:
cd /tmp
wget http://projects.doozan.com/uboot/install_uboot_mtd0.sh
chmod +x install_uboot_mtd0.sh ./install_uboot_mtd0.shedit:
Wenn ich das Netzwerk neustarten will, kommt folgender Fehler:
Code:
root@debian ~ > /etc/init.d/networking restart[....] Running /etc/init.d/networking restart is deprecated because it may not r[warnble some interfaces ... (warning).
[....] Reconfiguring network interfaces...err, eth0: ioctl SIOCGIFHWADDR: No such device
Failed to bring up eth0.
done.
root@debian ~ >
Zuletzt bearbeitet von einem Moderator:
