OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"!!!

[VDRDAU]

Mit Firefox, also ich probiers jetzt mal mit dem IE

Sch..., du hast (wieder mal) recht gehabt, du Teufelskerl !
Mit dem IE klappt auch der Flashvorgang. Ich schließe das Teil jetzt gleich mal an den Switch, muss ich dazu dann am TP-Link wieder einen Ethernet-Port wählen (gelb, 1-4) oder muss es dann der Internet-Port (blau) sein ?

 

[fualex]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Falls mal jemand zeit hat. Bräuchte ich den Output von dmesg für jeden verfügbaren Reader. Und zwar abziehen, dranstecken und dann so die letzten 40 Zeilen. Das kommt mit in den Watchdog....

Ich bin bereit. Ist die Reinfolge richtig? : ssh -> dmesg -> smargo abziehen, dranstecken -> Info kopieren. Einfach dmesg? Oder noch etwas? Danke

 

[treblade]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Hallo kann mir jemand sagen warum der Paketmanager nicht funktioniert ich bekomme immer den folgenden Fehler.


Downloading

Sie müssen registriert sein, um Links zu sehen.

Sie müssen registriert sein, um Links zu sehen.

.
wget: server returned error: HTTP/1.1 404 Not Foundwget: server returned error: HTTP/1.1 404 Not FoundCollected errors: * opkg_download: Failed to download

Sie müssen registriert sein, um Links zu sehen.

, wget returned 1. * opkg_download: Failed to download

Sie müssen registriert sein, um Links zu sehen.

, wget returned 1.

 

[Matrixx200x]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Wer lesen kann ist klar im verteil !!!!!!!!!!!!

6 Post vorher wurde diese Frage beantwortet !!!!!!!!!!!!!!!!!!

Seite 44 letzter Post.

 

[derdigge]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@ Fualex, genau so!
Wichtig wäre das für die Easymouse, dann baue ich ein semi udev direkt mit ein!

@VRDAU
Gugg mal n paar Seiten zuvor hab ich das schonmal lang und breit durchgefatzt!

@treblade
ist ja nicht so als hätteste das vorgestrn erst gebracht!

@All
Watchdog leistet schon sehr gute Arbeit!
Ihr werdet hoch erfreut sein ..... little bit more testing!
Ich brauche dann die Logs vom an und abstecken des Geräts,
dann mache ich ein Autoreadermount ^^.

Es geht jetzt schon echt flott, kann Karte rausnehmen, wieder reinstecken.
Reader abziehen reinstecken. Er überlebt einfach alles :]]]

Ich würde gern halt noch den Automount der Easymouse einbaun, dann sollte es echt perfekt sein.
Hab jetzt schon 7kb an raw Code getippt!

 

[Osprey]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Guten Morgen zusammen,

falls dir auch die Daten vom Omnikey Reader helfen, anbei der output von dmseg nach dem einstecken.
Allerdings muss ich sagen, das meine beide Reader seitdem ich den Loadbalancer in oscam deaktiviert habe, und einen aktivhub benutze, nicht mehr ausgestiegen sind.

LG

Spoiler

root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (DeepThought@Magrathea) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #1 Thu Oct 25 19:47:45 MSK 2012
[ 0.000000] MyLoader: sysp=ffffffff, boardp=ffffffff, parts=f7ffffff
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802ef060, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29008k/32768k available (2208k kernel code, 3760k reserved, 413k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.360000] bio: create slab <bio-0> at 0
[ 0.370000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.420000] NET: Registered protocol family 1
[ 0.420000] PCI: CLS 0 bytes, default 32
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 56
[ 0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.470000] io scheduler noop registered
[ 0.470000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.510000] console [ttyS0] enabled, bootconsole disabled
[ 0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
[ 0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.560000] 0x000000020000-0x00000010b600 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] 0x00000010b600-0x0000007f0000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.590000] mtd: partition "rootfs" set to be root filesystem
[ 0.600000] mtd: partition "rootfs_data" created automatically, ofs=3A0000, len=450000
[ 0.610000] 0x0000003a0000-0x0000007f0000 : "rootfs_data"
[ 0.620000] 0x0000007f0000-0x000000800000 : "art"
[ 0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[ 0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 0.930000] rtl8366rb: probed
[ 0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.240000] TCP cubic registered
[ 1.250000] NET: Registered protocol family 17
[ 1.250000] Bridge firewalling registered
[ 1.260000] 8021q: 802.1Q VLAN Support v1.8
[ 1.260000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.270000] Freeing unused kernel memory: 212k freed
[ 3.330000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[ 3.330000] eth0: link up (1000Mbps/Full duplex)
[ 3.360000] Registered led device: tp-link:green:usb
[ 3.360000] Registered led device: tp-link:green:system
[ 3.360000] Registered led device: tp-link:green:qss
[ 3.360000] Registered led device: tp-link:green:wlan
[ 6.640000] JFFS2 notice: (437) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 12 of xref (0 dead, 0 orphan) found.
[ 6.820000] eth0: link down
[ 8.710000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 8.720000] Backport based on wireless-testing.git master-2012-09-07
[ 8.730000] compat.git: wireless-testing.git
[ 8.760000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.760000] cfg80211: World regulatory domain updated:
[ 8.770000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.790000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.800000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.030000] usbcore: registered new interface driver usbfs
[ 9.030000] usbcore: registered new interface driver hub
[ 9.040000] usbcore: registered new device driver usb
[ 9.490000] ath: EEPROM regdomain: 0x0
[ 9.490000] ath: EEPROM indicates default country code should be used
[ 9.490000] ath: doing EEPROM country->regdmn map search
[ 9.490000] ath: country maps to regdmn code: 0x3a
[ 9.490000] ath: Country alpha2 being used: US
[ 9.490000] ath: Regpair used: 0x3a
[ 9.500000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.500000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[ 9.510000] cfg80211: Calling CRDA for country: US
[ 9.510000] cfg80211: Regulatory domain changed to country: US
[ 9.520000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.530000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.530000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.540000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.550000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.560000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.570000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.810000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.910000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.920000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.930000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 9.960000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 9.980000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 9.980000] hub 1-0:1.0: USB hub found
[ 9.990000] hub 1-0:1.0: 1 port detected
[ 10.010000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 10.210000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.330000] usbcore: registered new interface driver usbserial
[ 10.330000] USB Serial support registered for generic
[ 10.360000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 10.510000] hub 1-1:1.0: USB hub found
[ 10.510000] hub 1-1:1.0: 4 ports detected
[ 10.520000] usbcore: registered new interface driver usbserial_generic
[ 10.520000] usbserial: USB Serial Driver core
[ 10.540000] USB Serial support registered for FTDI USB Serial Device
[ 10.550000] usbcore: registered new interface driver ftdi_sio
[ 10.560000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 10.820000] usb 1-1.3: new full-speed USB device number 3 using ehci-platform
[ 11.050000] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[ 13.490000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[ 13.790000] eth0: link up (1000Mbps/Full duplex)
[ 13.800000] device eth0.1 entered promiscuous mode
[ 13.800000] device eth0 entered promiscuous mode
[ 13.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 13.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 15.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.260000] device wlan0 entered promiscuous mode
[ 18.130000] br-lan: port 2(wlan0) entered forwarding state
[ 18.130000] br-lan: port 2(wlan0) entered forwarding state
[ 20.130000] br-lan: port 2(wlan0) entered forwarding state
[ 38.090000] usb 1-1.3: usbfs: usb_submit_urb returned -140
[ 39.200000] usb 1-1.4: usbfs: usb_submit_urb returned -140
[ 152.860000] device wlan0 left promiscuous mode
[ 152.860000] br-lan: port 2(wlan0) entered disabled state
[ 154.940000] device wlan0 entered promiscuous mode
[ 155.260000] br-lan: port 2(wlan0) entered forwarding state
[ 155.270000] br-lan: port 2(wlan0) entered forwarding state
[ 157.270000] br-lan: port 2(wlan0) entered forwarding state
[ 1892.160000] br-lan: port 2(wlan0) entered disabled state
[ 1892.280000] device wlan0 left promiscuous mode
[ 1892.290000] br-lan: port 2(wlan0) entered disabled state
[ 1894.000000] device wlan0 entered promiscuous mode
[ 1894.370000] br-lan: port 2(wlan0) entered forwarding state
[ 1894.370000] br-lan: port 2(wlan0) entered forwarding state
[ 1896.370000] br-lan: port 2(wlan0) entered forwarding state
[ 1925.020000] device wlan0 left promiscuous mode
[ 1925.020000] br-lan: port 2(wlan0) entered disabled state
[ 1926.890000] device wlan0 entered promiscuous mode
[ 1927.200000] br-lan: port 2(wlan0) entered forwarding state
[ 1927.210000] br-lan: port 2(wlan0) entered forwarding state
[ 1929.210000] br-lan: port 2(wlan0) entered forwarding state
[180908.590000] ath: phy0: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020 DMADBG_7=0x000286c0
[180908.600000] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
[228208.480000] usb 1-1.4: USB disconnect, device number 4
[228214.890000] usb 1-1.4: new full-speed USB device number 5 using ehci-platform
[228220.260000] usb 1-1.3: USB disconnect, device number 3
[228229.050000] usb 1-1.3: new full-speed USB device number 6 using ehci-platform

 

[VDRDAU]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Hallo,
nun rennt auch alles bei mir. Tausend Dank für deine Mühe und diese super Arbeit. Allererste Sahne.

 

[fualex]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@ Fualex, genau so!
Wichtig wäre das für die Easymouse, dann baue ich ein semi udev direkt mit ein!

Ich würde gern halt noch den Automount der Easymouse einbaun, dann sollte es echt perfekt sein.
Hab jetzt schon 7kb an raw Code getippt!

Hi derdigge, ich habe nur ein smargo. Sorry.

Spoiler

root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (DeepThought@Magrathea) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #1 Fri Oct 19 17:03:59 CEST 2012
[ 0.000000] MyLoader: sysp=4b1bf7b5, boardp=9002c600, parts=6bde8914
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9344 rev 2
[ 0.000000] Clocks: CPU:560.000MHz, DDR:450.000MHz, AHB:225.000MHz, Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 08000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00008000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00008000
[ 0.000000] On node 0 totalpages: 32768
[ 0.000000] free_area_init_node: node 0, pgdat 802ef080, node_mem_map 81000000
[ 0.000000] Normal zone: 256 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 32512 pages, LIFO batch:7
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
[ 0.000000] Kernel command line: board=TL-WDR4300 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 126472k/131072k available (2208k kernel code, 4600k reserved, 413k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 278.93 BogoMIPS (lpj=1394688)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.070000] Mount-cache hash table entries: 512
[ 0.080000] NET: Registered protocol family 16
[ 0.080000] gpiochip_add: registered GPIOs 0 to 22 on device: ath79
[ 0.090000] MIPS: machine is TP-LINK TL-WDR3600/4300/4310
[ 0.090000] registering PCI controller with io_map_base unset
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.310000] PCI host bridge to bus 0000:00
[ 0.320000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.320000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.330000] pci 0000:00:00.0: [168c:0033] type 0 class 0x000280
[ 0.330000] pci 0000:00:00.0: invalid calibration data
[ 0.330000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit]
[ 0.330000] pci 0000:00:00.0: reg 30: [mem 0x00000000-0x0000ffff pref]
[ 0.330000] pci 0000:00:00.0: supports D1
[ 0.330000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 0.330000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[ 0.340000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[ 0.340000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.350000] Switching to clocksource MIPS
[ 0.350000] NET: Registered protocol family 2
[ 0.360000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.360000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.370000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.370000] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.380000] TCP reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] NET: Registered protocol family 1
[ 0.400000] PCI: CLS 0 bytes, default 32
[ 0.410000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 247
[ 0.430000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.450000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.480000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.490000] console [ttyS0] enabled, bootconsole disabled
[ 0.500000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.510000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.510000] 5 tp-link partitions found on MTD device spi0.0
[ 0.520000] Creating 5 MTD partitions on "spi0.0":
[ 0.520000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.530000] 0x000000020000-0x00000010972c : "kernel"
[ 0.530000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] 0x00000010972c-0x0000007f0000 : "rootfs"
[ 0.550000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] mtd: partition "rootfs" set to be root filesystem
[ 0.570000] mtd: partition "rootfs_data" created automatically, ofs=3C0000, len=430000
[ 0.580000] 0x0000003c0000-0x0000007f0000 : "rootfs_data"
[ 0.590000] 0x0000007f0000-0x000000800000 : "art"
[ 0.590000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.730000] ag71xx_mdio: probed
[ 0.730000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.310000] eth0: Atheros AR8327 switch driver attached.
[ 2.470000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd033, driver=Atheros AR8216/AR8236/AR8316]
[ 2.480000] TCP cubic registered
[ 2.480000] NET: Registered protocol family 17
[ 2.490000] Bridge firewalling registered
[ 2.490000] 8021q: 802.1Q VLAN Support v1.8
[ 2.500000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.510000] Freeing unused kernel memory: 212k freed
[ 4.170000] Registered led device: tp-link:blue:qss
[ 4.170000] Registered led device: tp-link:blue:system
[ 4.170000] Registered led device: tp-link:green:usb1
[ 4.170000] Registered led device: tp-link:green:usb2
[ 4.170000] Registered led device: tp-link:blue:wlan2g
[ 5.470000] eth0: link up (1000Mbps/Full duplex)
[ 7.410000] JFFS2 notice: (480) jffs2_build_xattr_subsystem: complete building xattr subsystem, 23 of xdatum (0 unchecked, 22 orphan) and 34 of xref (0 dead, 22 orphan) found.
[ 7.560000] eth0: link down
[ 9.030000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 9.040000] Backport based on wireless-testing.git master-2012-09-07
[ 9.050000] compat.git: wireless-testing.git
[ 9.070000] cfg80211: Calling CRDA to update world regulatory domain
[ 9.080000] cfg80211: World regulatory domain updated:
[ 9.080000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.090000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.100000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.110000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.300000] usbcore: registered new interface driver usbfs
[ 9.310000] usbcore: registered new interface driver hub
[ 9.310000] usbcore: registered new device driver usb
[ 9.680000] ath: EEPROM regdomain: 0x0
[ 9.680000] ath: EEPROM indicates default country code should be used
[ 9.680000] ath: doing EEPROM country->regdmn map search
[ 9.680000] ath: country maps to regdmn code: 0x3a
[ 9.680000] ath: Country alpha2 being used: US
[ 9.680000] ath: Regpair used: 0x3a
[ 9.680000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.680000] Registered led device: ath9k-phy0
[ 9.680000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 9.690000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 9.700000] ath: EEPROM regdomain: 0x0
[ 9.700000] ath: EEPROM indicates default country code should be used
[ 9.700000] ath: doing EEPROM country->regdmn map search
[ 9.700000] ath: country maps to regdmn code: 0x3a
[ 9.700000] ath: Country alpha2 being used: US
[ 9.700000] ath: Regpair used: 0x3a
[ 9.700000] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 9.700000] Registered led device: ath9k-phy1
[ 9.700000] ieee80211 phy1: Atheros AR9300 Rev:4 mem=0xb0000000, irq=40
[ 9.710000] cfg80211: Calling CRDA for country: US
[ 9.720000] cfg80211: Regulatory domain changed to country: US
[ 9.730000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.730000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.740000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.750000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.760000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.770000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.770000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.960000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 10.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.050000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 10.060000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 10.100000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 10.120000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 10.120000] hub 1-0:1.0: USB hub found
[ 10.130000] hub 1-0:1.0: 1 port detected
[ 10.150000] nf_conntrack version 0.5.0 (1979 buckets, 7916 max)
[ 10.310000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.410000] usbcore: registered new interface driver usbserial
[ 10.410000] USB Serial support registered for generic
[ 10.450000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 10.600000] hub 1-1:1.0: USB hub found
[ 10.600000] hub 1-1:1.0: 4 ports detected
[ 10.610000] usbcore: registered new interface driver usbserial_generic
[ 10.610000] usbserial: USB Serial Driver core
[ 10.630000] USB Serial support registered for FTDI USB Serial Device
[ 10.640000] usbcore: registered new interface driver ftdi_sio
[ 10.640000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 10.890000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[ 11.000000] ftdi_sio 1-1.1:1.0: FTDI USB Serial Device converter detected
[ 11.000000] usb 1-1.1: Detected FT232BM
[ 11.010000] usb 1-1.1: Number of endpoints 2
[ 11.010000] usb 1-1.1: Endpoint 1 MaxPacketSize 16384
[ 11.020000] usb 1-1.1: Endpoint 2 MaxPacketSize 16384
[ 11.020000] usb 1-1.1: Setting MaxPacketSize 64
[ 11.030000] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 11.040000] usb 1-1.1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 13.100000] device eth0.1 entered promiscuous mode
[ 13.110000] device eth0 entered promiscuous mode
[ 14.500000] eth0: link up (1000Mbps/Full duplex)
[ 14.540000] br-lan: port 1(eth0.1) entered forwarding state
[ 14.540000] br-lan: port 1(eth0.1) entered forwarding state
[ 15.440000] cfg80211: Calling CRDA for country: DE
[ 15.440000] cfg80211: Regulatory domain changed to country: DE
[ 15.450000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 15.460000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 15.470000] cfg80211: (5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 15.470000] cfg80211: (5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 15.480000] cfg80211: (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 16.540000] br-lan: port 1(eth0.1) entered forwarding state
[ 23.240000] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 23.250000] ftdi_sio 1-1.1:1.0: device disconnected
[ 160.890000] usb 1-1.1: USB disconnect, device number 3
[ 182.380000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
[ 187.490000] ftdi_sio 1-1.1:1.0: FTDI USB Serial Device converter detected
[ 187.500000] usb 1-1.1: Detected FT232BM
[ 187.500000] usb 1-1.1: Number of endpoints 2
[ 187.500000] usb 1-1.1: Endpoint 1 MaxPacketSize 16384
[ 187.510000] usb 1-1.1: Endpoint 2 MaxPacketSize 16384
[ 187.510000] usb 1-1.1: Setting MaxPacketSize 64
[ 187.530000] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 187.530000] usb 1-1.1: FTDI USB Serial Device converter now attached to ttyUSB0

 

[fualex]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@Fualex

Die regel funktioniert nur wenn der Reader abschmiert, also kurz vom Usb trennt.
Was steht im Log nachdem Oscam beendet wurde?

Leider garnichts. Ist einfach kein oscam unter Prozessen zu sehen :-( Sowie Oscam Log nur die letzte EMMs.

 

[FraLe]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@derdigge

dmesg Ausgabe Router T-Plink WR1043ND und Smargo

Spoiler

root@OpenWrt:~# dmesg
[ 0.000000] Linux version 3.3.8 (DeepThought@Magrathea) (gcc version 4.6.4 20121001 (prerelease) (Linaro GCC 4.6-2012.10) ) #1 Fri Oct 19 17:03:59 CEST 2012
[ 0.000000] MyLoader: sysp=aaaaaaaa, boardp=aaaaaaaa, parts=aaaaaaaa
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9132 rev 2
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802ef080, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8128 pages, LIFO batch:0
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=TL-WR1043ND console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 29008k/32768k available (2208k kernel code, 3760k reserved, 413k data, 212k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 21 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR1043ND
[ 0.360000] bio: create slab <bio-0> at 0
[ 0.370000] Switching to clocksource MIPS
[ 0.380000] NET: Registered protocol family 2
[ 0.380000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.380000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.390000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.390000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.400000] TCP reno registered
[ 0.400000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.410000] NET: Registered protocol family 1
[ 0.420000] PCI: CLS 0 bytes, default 32
[ 0.440000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.440000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.450000] msgmni has been set to 56
[ 0.460000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.460000] io scheduler noop registered
[ 0.470000] io scheduler deadline registered (default)
[ 0.470000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
[ 0.510000] console [ttyS0] enabled, bootconsole disabled
[ 0.530000] m25p80 spi0.0: found s25sl064a, expected m25p80
[ 0.530000] m25p80 spi0.0: s25sl064a (8192 Kbytes)
[ 0.540000] 5 tp-link partitions found on MTD device spi0.0
[ 0.540000] Creating 5 MTD partitions on "spi0.0":
[ 0.550000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.560000] 0x000000020000-0x00000010b600 : "kernel"
[ 0.560000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] 0x00000010b600-0x0000007f0000 : "rootfs"
[ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.590000] mtd: partition "rootfs" set to be root filesystem
[ 0.600000] mtd: partition "rootfs_data" created automatically, ofs=3C0000, len=430000
[ 0.610000] 0x0000003c0000-0x0000007f0000 : "rootfs_data"
[ 0.620000] 0x0000007f0000-0x000000800000 : "art"
[ 0.620000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.630000] Realtek RTL8366RB ethernet switch driver version 0.2.3
[ 0.750000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
[ 0.750000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
[ 0.930000] rtl8366rb: probed
[ 0.940000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.240000] TCP cubic registered
[ 1.250000] NET: Registered protocol family 17
[ 1.250000] Bridge firewalling registered
[ 1.260000] 8021q: 802.1Q VLAN Support v1.8
[ 1.270000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.270000] Freeing unused kernel memory: 212k freed
[ 3.330000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[ 3.330000] eth0: link up (1000Mbps/Full duplex)
[ 3.360000] Registered led device: tp-link:green:usb
[ 3.360000] Registered led device: tp-link:green:system
[ 3.360000] Registered led device: tp-link:green:qss
[ 3.360000] Registered led device: tp-link:green:wlan
[ 6.680000] JFFS2 notice: (437) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 19 of xref (0 dead, 7 orphan) found.
[ 6.850000] eth0: link down
[ 8.770000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
[ 8.780000] Backport based on wireless-testing.git master-2012-09-07
[ 8.790000] compat.git: wireless-testing.git
[ 8.820000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.820000] cfg80211: World regulatory domain updated:
[ 8.830000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.840000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.840000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.850000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 8.860000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 8.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.090000] usbcore: registered new interface driver usbfs
[ 9.100000] usbcore: registered new interface driver hub
[ 9.100000] usbcore: registered new device driver usb
[ 9.560000] ath: EEPROM regdomain: 0x0
[ 9.560000] ath: EEPROM indicates default country code should be used
[ 9.560000] ath: doing EEPROM country->regdmn map search
[ 9.560000] ath: country maps to regdmn code: 0x3a
[ 9.560000] ath: Country alpha2 being used: US
[ 9.560000] ath: Regpair used: 0x3a
[ 9.570000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 9.570000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
[ 9.580000] cfg80211: Calling CRDA for country: US
[ 9.580000] cfg80211: Regulatory domain changed to country: US
[ 9.590000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.600000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 9.600000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 9.610000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.620000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.630000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.640000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 9.870000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.980000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 9.990000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 9.990000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 10.030000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 10.050000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 10.050000] hub 1-0:1.0: USB hub found
[ 10.060000] hub 1-0:1.0: 1 port detected
[ 10.080000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 10.280000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.400000] usbcore: registered new interface driver usbserial
[ 10.400000] USB Serial support registered for generic
[ 10.430000] usb 1-1: new full-speed USB device number 2 using ehci-platform
[ 10.580000] usbcore: registered new interface driver usbserial_generic
[ 10.590000] usbserial: USB Serial Driver core
[ 10.610000] USB Serial support registered for FTDI USB Serial Device
[ 10.620000] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[ 10.630000] usb 1-1: Detected FT232BM
[ 10.630000] usb 1-1: Number of endpoints 2
[ 10.630000] usb 1-1: Endpoint 1 MaxPacketSize 16384
[ 10.640000] usb 1-1: Endpoint 2 MaxPacketSize 16384
[ 10.640000] usb 1-1: Setting MaxPacketSize 64
[ 10.650000] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 10.660000] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 10.660000] usbcore: registered new interface driver ftdi_sio
[ 10.670000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
[ 13.460000] ar71xx: pll_reg 0xb8050014: 0x1a000000
[ 13.770000] eth0: link up (1000Mbps/Full duplex)
[ 13.780000] device eth0.1 entered promiscuous mode
[ 13.790000] device eth0 entered promiscuous mode
[ 13.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 13.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 15.820000] br-lan: port 1(eth0.1) entered forwarding state
[ 16.150000] cfg80211: Calling CRDA for country: AT
[ 16.150000] cfg80211: Regulatory domain changed to country: AT
[ 16.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 16.160000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.170000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.180000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 16.190000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 19.050000] device wlan0 entered promiscuous mode
[ 20.270000] br-lan: port 2(wlan0) entered forwarding state
[ 20.280000] br-lan: port 2(wlan0) entered forwarding state
[ 22.280000] br-lan: port 2(wlan0) entered forwarding state
[ 36.670000] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 36.680000] ftdi_sio 1-1:1.0: device disconnected
[ 335.910000] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[ 335.910000] usb 1-1: Detected FT232BM
[ 335.920000] usb 1-1: Number of endpoints 2
[ 335.920000] usb 1-1: Endpoint 1 MaxPacketSize 16384
[ 335.930000] usb 1-1: Endpoint 2 MaxPacketSize 16384
[ 335.930000] usb 1-1: Setting MaxPacketSize 64
[ 335.940000] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[ 335.940000] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 336.240000] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 336.250000] ftdi_sio 1-1:1.0: device disconnected
[22035.780000] usb 1-1: USB disconnect, device number 2
[22040.540000] usb 1-1: new full-speed USB device number 3 using ehci-platform
[22041.140000] ftdi_sio 1-1:1.0: FTDI USB Serial Device converter detected
[22041.140000] usb 1-1: Detected FT232BM
[22041.150000] usb 1-1: Number of endpoints 2
[22041.150000] usb 1-1: Endpoint 1 MaxPacketSize 16384
[22041.150000] usb 1-1: Endpoint 2 MaxPacketSize 16384
[22041.160000] usb 1-1: Setting MaxPacketSize 64
[22041.180000] ftdi_sio ttyUSB0: Unable to read latency timer: -32
[22041.180000] usb 1-1: FTDI USB Serial Device converter now attached to ttyUSB0

 

[derdigge]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

Danke für eure Hilfe!
Weiterentwicklung des Smargo Watchdog Moduls/pcsc Moduls hat mittlerweile 2 Kaffekannen verbraten.
Aber es hat sich gelohnt, ich kann machen was ich will, ich krieg den nichtmehr tot gespielt ^^.

looking for easymouser!!!!
dmesg / oscam.log / logread
nach an und abstecken

am besten einer mit skype der mal ne halbe Stunde Zeit hat zum chatten!

 

[fruttifresh76]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@Link Removed

Habe die Easymouse noch OVP hier rumliegen....

 

[derdigge]

wo issn hier ?



Gesendet von meinem iPad mit Tapatalk HD

 

[fruttifresh76]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

@derdigge

Neben meinem Huawei EchoLife HG556a

 

[derdigge]

AW: OScam für etliche Router mit USB port, fix und fertig verpackt! Zum "Gleichessen"

ROFL!
Ich meine wohnst du mehr oben oder links oder rechts?
Vielleicht könnte ich se mit ja ausborgen zum scripten meine ich!

Das mit dem Smargo hab ich so perfekt hinbekommen im Watchdog.
Der erkennt jetzt sogar fehlconfig vom User und korrigiert das Automatisch!
Richtig finster ^^

Das selbe wäre halt bei der Easymouse auch drin. Derzeit mache ich nur einen
einfachen neustart bei "easymouse_panic". Ich weiß z.b. nicht ob /ttyusbxxx sich resetten lässt mit Kernelmodul xy......

Ich mein wor könnten das auch per skype remot machen,
müsstest halt nur mal von zeit zu zeit abziehen.

Wenn du mir nen Zugang auf dem Router geben könntest per ssh.
Machste ne nackte Falshung und random pw "watchdog".....