Ich konnte das Journaling folgendermaßen deaktivieren:
1. Backup von /etc/fstab: cp /etc/fstab /etc/fstab.backup
2. vi /etc/fstab, darin den mount Eintrag für /dev/mmcblk0p2 editieren ( bei mir die 1. Zeile ):
3. Reboot: shutdown -r now
4. tune2fs -O ^has_journal /dev/mmcblk0p2
5. e2fsck -f /dev/mmcblk0p2
6. Reboot: shutdown -r now
7. mount -o rw,remount /
8. cp /etc/fstab.backup /etc/fstab
9. Reboot shutdown -r now
Gruß
Leider hat das deaktivieren des Journals mir nicht geholfen
Im log steht nach ein paar Stunden wieder:
Code:
<-ECM (1<-)-03 received from 127.0.0.1
<-ECM (1<-)-03 received from 127.0.0.1
network ecm removed, to old (age: 3821 ms)
<-ECM (1<-)-03 received from 127.0.0.1
<-ECM (1<-)-03 received from 127.0.0.1
network ecm removed, to old (age: 2824 ms)
<-ECM (1<-)-03 received from 127.0.0.1
Leider hat das deaktivieren des Journals mir nicht geholfen :disappointed:
Im log steht nach ein paar Stunden wieder:
Code:
<-ECM (1<-)-03 received from 127.0.0.1
<-ECM (1<-)-03 received from 127.0.0.1
network ecm removed, to old (age: 3821 ms)
<-ECM (1<-)-03 received from 127.0.0.1
<-ECM (1<-)-03 received from 127.0.0.1
network ecm removed, to old (age: 2824 ms)
<-ECM (1<-)-03 received from 127.0.0.1
Ich konnte das Journaling folgendermaßen deaktivieren:
1. Backup von /etc/fstab: cp /etc/fstab /etc/fstab.backup
2. vi /etc/fstab, darin den mount Eintrag für /dev/mmcblk0p2 editieren ( bei mir die 1. Zeile ):
Ich habe meinen Raspi ja nochmal neu aufgesetzt. Bislang noch keine Problem. Naja letztes Mal kamen die timeouts ja auch erst zwei drei Wochen nach Aufsetzen.
So, 8 Tage nach der Neuinstallation wieder "timeout"
Ich kriegs nicht gebacken, hab mir extra mal ne Easymouse geholt, hatte vorher eine Quadmouse.
Gbosreader ist immer noch gelb und offline.
Hier mal meine Configs.
# gbox config file
# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 01 11 } 192.168.1.2 8024
F: { 12 } /var/log/ipc
# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }
# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
C: { 01 }
# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 01 }
# Auto Update
# 00 AU disable (default)
# 01 AU enable
# 02 AU auto
# 03 AU enable with ua,sa and ga filter !!!!! always use this !!!!!
A: { 03 }
# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }
# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }
# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 } 192.168.0.3 coolstream
# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 } 192.168.0.251 7025
# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
(in the dbox2 the gbox writes directly the CWs, 00 is the
recommended mode ! No drivers are required) use D* ** ONLY if
you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x*8) invert CTS detection on com2
#V: { 00 10 } #Slot 1
#V: { 00 20 } #Slot 2
#V: { 00 30 } #Slot 1+2
#V: { 00 3F } #Slot 1+2+SC8in1
V: { 00 05 } #only com-ports
# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
R: { 00 } 9600
# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
W: { 00 00 } 9600
# =============================================================================
# extra options to override default setting in case you expirience Problems,
# normaly these setings are not required.
# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
# Ist nicht Aktiv geschaltet ,also keine Funktion
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 03 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
#F: { 58 } 03 // nds
# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1
# set stay alive ping time in seconds (default is 300)
#F: { A0 } 300
# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
F: { A1 } 1
# descrambler selection by camd.socket private descriptor (0 - index mode, 1 - mask mode), mask mode is default
#F: { AA } 1
#F: { 12 } /var/log/gbox
/SPOILER]
# allow maximum 06 share level for recieved card data
I: { 03 }
# 01 repeat EMM's
# 00 consider every EMM only once
# 01 restart pid on overflow
# 1* reset ENX on every channel change
# 2* rezap after start (calling pzapit -rz --pal)
# *1 check/reset ENX freezes on FTA
# *2 check/reset ENX freezes on PayTV
# *3 check/reset ENX freezes on FTA and PayTV
# 00 write nothing in atack.txt
# 01 write into atack.txt: password is wrong
# 02 write into atack.txt: ID unknown
# 04 write into atack.txt: IP is wrong
# 08 write into atack.txt: port is worng
# 10 write into atack.txt: share.stat
# 20 create online.log for online/offline logging
# 3F write everything. (combine bits for other combinations)
# 4000 send ecm again after 4 Seconds if no reply.
# 6000 resync decode after 6 Seconds if net decode failed
N: { 00 00 20 00 2500 4500 }
# Send ECM's at maximum 5 cards (please use this as default)
X: { 05 }
# Send ECM's in any case to these card ID's, even they are more then X:
# some examples ...
# G: { 17020000 1234 }
# G: { 0B000000 ABCD }
# G: { 05021510 AB34 }
# G: { 0D03A000 A234 }
ich habe 2x Quadmouse & 1x Easymouse für V13. Diee Eaysymouse direkt am RPi & die
Quadmouse über aktiven Hub. Der RPi schafft die Spannung für die Quadmouse nicht.
Dann die udev Regeln für Deine Quadmouse anlegen, Seite 1 hier im Post. Nicht über IPC Manager,
sondern über die Konsole mit dmesg & dann die Regel nach etc/udev/ ...
Die Easymouse mit V13 als ttyUSBv13 umbenennen und in die gbox.cfg eintragen.
Deine udev Regel sollten etwa so aussehen
########################## Easymouse2 direkt am RPI4 ###############################
SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", ATTRS{serial}=="AB0JMM3E", SYMLINK+="ttyUSBv13"
########################## QUADMOUSE 1 USB ganz oben USB Hub ####################################
ATTRS{interface}=="Quad RS232-HS", SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", KERNELS=="1-1.3.4.4:1.0", SYMLINK+="mtv"
ATTRS{interface}=="Quad RS232-HS", SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", KERNELS=="1-1.3.4.4:1.1", SYMLINK+="hd2"
ATTRS{interface}=="Quad RS232-HS", SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", KERNELS=="1-1.3.4.4:1.2", SYMLINK+="orf1"
ATTRS{interface}=="Quad RS232-HS", SUBSYSTEMS=="usb", KERNEL=="ttyUSB*", KERNELS=="1-1.3.4.4:1.3", SYMLINK+="srg"
reboot
Dann funktioniert das auch einwandfrei mit einer Quadouse.