Es kommen mir zu wenige EMMs. Warum?

[ballzauber]

ich hab folgende configuration im reader, ist es normal das ich ne stunde verbunden und aufn sky sender bin und er keine emms bekommt bzw speichert !? laut reader status hat er folgendes geblock (4 / 0 / 0 / 8)

kommen da immer nur so wenige emms wenn die karte schon aktiviert ist ?! oder was stimmt da nicht vorhin war der client "au" mal kurz aktiv, da hat er ein emm geschrieben in den log aber das wars auch für die letzten 2 stunden

hat evtl jemand ne tipp ?!

saveemm-u                     = 1blockemm-unknown              = 1
blockemm-u                    = 1
blockemm-s                    = 1
blockemm-g                    = 1
blockemm-bylen                = 1-31,36,38,40-41,65-72,74-124,126,128-129,131,141-255

 

[DKett]

AW: Sky V14 EMM Sammelliste- Laber Thema

Blockemm-bylen kann raus, du blockst ja schon alles, da brauchst du nicht noch gleichzeitig was durch lassen.

 

[ballzauber]

AW: Sky V14 EMM Sammelliste- Laber Thema

ich will halt die emms per hand schreiben morgen kommt meine neue v14 ! Und die will ich per hand aktivieren ! Aber mich wunder halt das er ewig keinen bis kaum emms bekommt ! Und ich nicht weiß wieso !?

 

[mac50]

AW: Sky V14 EMM Sammelliste- Laber Thema

warte ab,wenn du deine Freischaltung für die neue V14 anforderst, wirst du mehr als dir lieb ist bekommen.
Wenn der Zauber vorbei ist nach ca. 10 Tagen kommen dann auch nur 1-2 Emm´s

 

[dia]

AW: Sky V14 EMM Sammelliste- Laber Thema

verlängerungsemm kannst du nur 4 mal bekommen am tag
verlängerungen nicht die von der aktivierung

soviele sind es auch nicht mehr
ohne die bösen sind es 20 emm´s

 

[ballzauber]

AW: Sky V14 EMM Sammelliste- Laber Thema

ok also die v14 die schon freigeschalten ist lief jetzt die ganze nacht und hat 0 emms bekommen von ner dbox mit cccam..... hab als sender sky krimi drauf.... na warten wir mal ab was heute nachmittag passiert =)

ich hoffe ich bekomme dann wenigstens emms zur freischaltung durch !

 

[dia]

AW: Es kommen mir zu wenige EMMs. Warum?

weiss nicht was du meinst
ist die v14 jetzt freigeschaltet oder nicht ????

nochmal dbox einmal stromlos machen einschalten und in ca einer halben std ist das emm da

natürlich wenn ihr 10 clints orf und noch andere karten habt
dauert es noch länger

 

[ballzauber]

AW: Es kommen mir zu wenige EMMs. Warum?

• 2014/10/29 15:08:10 4FA4F0 r sky [smartreader] Reader initialized (device=Serial:Reader 4D647G, detect=cd, mhz=480, cardmhz=369)
• 2014/10/29 15:08:11 4FA4F0 r sky [smartreader] card detected
• 2014/10/29 15:08:19 4FA4F0 r sky [smartreader] Error activating card.
• 2014/10/29 15:08:39 0 --- Skipped 2 duplicated log lines ---
• 2014/10/29 15:08:39 4FA4F0 r sky [smartreader] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
• 2014/10/29 15:08:39 4FA4F0 r sky [smartreader] card initializing error
• 2014/10/29 15:08:39 0 s init for all local cards done
• 2014/10/29 15:08:39 0 s anti cascading disabled

karte ist schon aktiviert, laut dem sky brief, aber noch nicht freigeschaltet ich muss sie nurnoch in ein gerät stecken und dann gehts los....

oben das war die init von der karte jetzt frage mein gerade an mal sehen ob emms gesendet werden

 

[pehedima]

AW: Es kommen mir zu wenige EMMs. Warum?

Solange deine Karte nicht korrekt gelesen wird, brauchst du dich um die EMMs nicht zu kümmern.

Poste deine kompletten Configs (oscam.conf, oscam.user, oscam.server und oscam.dvbapi).

 

[ballzauber]

AW: Es kommen mir zu wenige EMMs. Warum?

[global]logfile                       = /var/log/oscam.log
maxlogsize                    = 1000
preferlocalcards              = 1
readerrestartseconds          = 20
emmlogdir                     = /var/log/emm/


[cache]


[cccam]
port                          = 50000
nodeid                        = D95E3FE610E41584
version                       = 2.3.0

[reader]label                         = sky
description                   = Sky Deutschland
protocol                      = smartreader
device                        = Serial:Reader xxxxxx
autospeed                     = 0
caid                          = 098C
boxid                         = 12345678
ins7e11                       = 15
detect                        = cd
mhz                           = 480
cardmhz                       = 369
group                         = 1
emmcache                      = 1,1,10
blockemm-unknown              = 1
blockemm-u                    = 1
blockemm-s                    = 1
blockemm-g                    = 1
saveemm-u                     = 1
ndsversion                    = 2

[account]user                          = xxxxx
pwd                           = xxxxx
description                   = update
caid                          = 09C4,098C
monlevel                      = 2
keepalive                     = 1
au                            = sky
group                         = 1,2,3
services                      = sat-sky-starter,sat-sky-welt-extra,sat-sky-welt,sat-sky-film,sat-sky-filmhd,sat-sky-sportsd,sat-sky-sporthd,sat-sky-bundesligasd,sat-sky-bundesligahd,sat-sky-bluemovie,sat-sky-select,sat-sky-sonstige,orf,austriasat,hdplus
cccmaxhops                    = 2

Jetzt hat er die karte war ne fehler am reader =)

2014/10/29 15:54:10   53F790 r sky [smartreader] Extended xx detected2014/10/29 15:54:10   53F790 r sky [smartreader] FuseByte: 00
2014/10/29 15:54:10   53F790 r sky [smartreader] Region Code: 
2014/10/29 15:54:10   53F790 r sky [smartreader] Country Code: DEU
2014/10/29 15:54:11   53F790 r sky [smartreader] Pincode read: xxxx
2014/10/29 15:54:11   53F790 r sky [smartreader] PCB settings: FF FF FF FF
2014/10/29 15:54:11   53F790 r sky [smartreader] type: VideoGuard Sky Austria/Germany (098C), caid: 098C
2014/10/29 15:54:11   53F790 r sky [smartreader] serial: ########, BoxID: ########, baseyear:
2014/10/29 15:54:11   53F790 r sky [smartreader] ready for requests
2014/10/29 15:54:11   53F790 r sky [smartreader] found card system videoguard2
2014/10/29 15:54:11   53F790 r sky [videoguard2] THIS WAS A SUCCESSFUL START ATTEMPT No  1 out of max alloted of 1
2014/10/29 15:54:11   53F790 r sky [videoguard2] card detected
2014/10/29 15:54:11   53F790 r sky [videoguard2] type: VideoGuard Sky Austria/Germany (098C)

2014/10/29 15:54:24 53F790 r sky [videoguard2] classD3 ins54: no cw --> Card needs pairing/extra data
2014/10/29 15:54:24 53F790 r sky [videoguard2] classD3 ins54: no cw --> No tier found
2014/10/29 15:54:24 53F790 r sky [videoguard2] classD3 ins54: no cw --> Tier expired
2014/10/29 15:54:24 56FCD0 c xxx (098C&000000/01FB/0017/98:6AB2B2F76C97A78C895826B077E2A3A0): not found (188 ms) by sky - Sky Krimi

 

[pehedima]

Bitte konfiguriere noch das WebIf in der oscam.conf und poste die oscam.log vom oscam Start aus.

Edit:
Karte passt jetzt WebIf noch nicht

Gesendet von meiner Handquetsche

 

[ballzauber]

oscam.conf

Spoiler

[webif]httpport                      = 83
httpuser                      = root
httppwd                       = root
httpcss                       = /cs/oscam/template/neu/Blue_Shadow_V.2.css
httptpl                       = /cs/oscam/template/neu/
httphelplang                  = de
httprefresh                   = 40
httphideidleclients           = 1
httpshowpicons                = 1
httpallowed                   = 192.168.1.0-192.168.1.10
aulow                         = 120
hideclient_to                 = 30

Log

Spoiler

------------------------------------------------------------------------------->> OSCam <<  cardserver started at Wed Oct 29 15:54:02 2014
-------------------------------------------------------------------------------
2014/10/29 15:54:02        0 s >> OSCam <<  cardserver started, version 1.20-unstable_svn, build r9952 (mipsel-linux-uclibc-libusb)
2014/10/29 15:54:02        0 s creating pidfile /tmp/.oscam/oscam.pid with pid 880
2014/10/29 15:54:02        0 s services reloaded: 0 services freed, 17 services loaded, rejected 0
2014/10/29 15:54:02        0 s userdb reloaded: 3 accounts loaded, 0 expired, 2 disabled
2014/10/29 15:54:02        0 s signal handling initialized
2014/10/29 15:54:02        0 s 286 service-id's loaded in 31 ms
2014/10/29 15:54:02        0 s 41 tier-id's loaded
2014/10/29 15:54:02        0 s 3 provid's loaded
2014/10/29 15:54:02        0 s monitor: initialized (fd=6, port=988)
2014/10/29 15:54:02        0 s cccam: initialized (fd=7, port=50000)
2014/10/29 15:54:02        0 s sky [smartreader] creating thread for device Serial:Reader 4D9597E
2014/10/29 15:54:02   4FA0F0 h webif: decompressed 117384 bytes back into 272840 bytes
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/CACHEEXPAGE.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;3669847385;1.20-unstable_svn;9952;CS_CACHEEX-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/CONFIGMENU.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;1384511551;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/FAILBAN.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;1457764346;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02        0 s loadbalancer: can't read from file /tmp/.oscam/stat
2014/10/29 15:54:02        0 s waiting for local card init
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/CSS.tpl is in the old template format without revision info. Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;3838356416;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/HEADERSHORT.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;267516716;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/LOGPAGE.tpl is in the old template format without revision info. Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;2684068055;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/READERCONFIG.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;2434021740;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/READERCONFIGIRDETO.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;1891872387;1.20-unstable_svn;9952;READER_IRDETO-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/READERS.tpl is in the old template format without revision info. Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;4094589856;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/SCANUSB.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;3319773669;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/STATUS.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r9705). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;2990934085;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/CLIENTSTATUSBIT.tpl was created for an older revision of OSCam and was changed in original OSCam (1.20-unstable_svn,r6881). Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;1837667586;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/USEREDIT.tpl is in the old template format without revision info. Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;4087845972;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h WARNING: Your http disk template /cs/oscam/template/neu/USERCONFIGLIST.tpl is in the old template format without revision info. Please consider upgrading it!
2014/10/29 15:54:02   4FA0F0 h If you are sure that it is current, add the following line at the beginning of the template to suppress this warning: <!--OSCam;891392823;1.20-unstable_svn;9952;-->
2014/10/29 15:54:02   4FA0F0 h HTTP Server running. ip=0.0.0.0 port=83
2014/10/29 15:54:02   53F790 r sky [smartreader] Reader initialized (device=Serial:Reader 4D9597E, detect=cd, mhz=480, cardmhz=369)
2014/10/29 15:54:03   53F790 r sky [smartreader] card detected
2014/10/29 15:54:08   53F790 r sky [smartreader] ATR: xx xx xx xx xx x xx xx xx xx 69 FF 4A xx F0 00 00 xx xx xx 
2014/10/29 15:54:08   53F790 r sky [smartreader] Init card protocol T0, FI=1, F=372, D=16, N=2
2014/10/29 15:54:08   53F790 r sky [smartreader] Calculated work ETU is 4.84 us reader mhz = 480
2014/10/29 15:54:08   53F790 r sky [smartreader] Effective reader settings mhz =480 F= 372 D= 16 N=2 T=0 inv=1 parity=ODD
2014/10/29 15:54:09   53F790 r sky [smartreader] ATR Fsmax is 5 MHz, clocking card to wanted user cardspeed off 4.80 MHz (specified in reader->mhz)
2014/10/29 15:54:10   53F790 r sky [smartreader] Card type:   P1TV
2014/10/29 15:54:10   53F790 r sky [smartreader] Rom version: xxx
2014/10/29 15:54:10   53F790 r sky [smartreader] Credit available on card: 0 euro
2014/10/29 15:54:10   53F790 r sky [smartreader] Extended 4C detected
2014/10/29 15:54:10   53F790 r sky [smartreader] FuseByte: 00
2014/10/29 15:54:10   53F790 r sky [

Block EMM im reader

Spoiler

[COLOR=black][FONT=monospace]emmcache                = 1,1,2
[/FONT][/COLOR]saveemm-u               = 1
blockemm-unknown        = 1
blockemm-g              = 1
blockemm-s              = 1 
[COLOR=black][FONT=monospace]blockemm-bylen          = 1-31,36,38,40-41,65-72,74-124,126,128-129,131,141-255 [/FONT][/COLOR]

soll ich es lieber so eintragen ? Oder schreibt er dann auch emms direkt auf die karte !? Ich will die emms eigentlich per hand selber schreiben !

 

[dia]

AW: Es kommen mir zu wenige EMMs. Warum?

block by len rauswerfen
blockemm-u=1 eintragen

dann kannste von hand schreiben

 

[ballzauber]

AW: Es kommen mir zu wenige EMMs. Warum?

oscam.server
[

Spoiler

QUOTE][reader]label = skydescription = Sky Deutschland
protocol = smartreader
device = Serial:Reader xxxxxx
autospeed = 0
caid = 098C
boxid = 12345678
ins7e11 = 15
detect = cd
mhz = 480
cardmhz = 369
group = 1
emmcache = 1,1,10
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
saveemm-u = 1 ndsversion = 2[/QUOTE]

so ist es im moment und es kommen keine emm an client ist ne dbox 2 mit cccam

 

[dia]

AW: Es kommen mir zu wenige EMMs. Warum?

was für ein image ist da drauf hat die dbox auch au und die cccam 2.3.0 drauf sonst wird das nix

und die dbox sollte erst vom strom genommen werden dann einschalten
jetzt online aktivieren und du bekommst die emm´s für deine box

es sollte aber nur die v14 alleine laufen