Hallo,
ich wollte gestern NeutroluxHD auf den Pingu draufmachen lief auch ganz gut, im Display hat er U LD angezeigt und danach kam 7 70.
Also hab alles nochmal von vorne gemacht nur jetzt zeigt er kein U LD mehr an sondern gleich 7 70 egal welchen Stick ich nehme.
Vorher hatte ich Neuprolux drauf.Da hat das installieren gleich beim 1. mal geklappt.
Als ich probiert habe Spark zu starten kommt boot und dann Load im Display und nichts passiert mehr.
Hier mal die Logs vom Reciever beim normalen starten:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 08 09
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCCTimed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
und beim Aufspielen des Rescue Images:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 08 09
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading spark/mImage
...............................................................................................................................................
5140251 bytes read
Un-Protect Flash Bank # 1
....................................................................................................................................... done
................................................................................................................ done
Erased 112 sectors
Copy to Flash...
danach passiert nichts mehr und es steht 5199 im Display.
Ziemlich langer Beitrag geworden,hoffe ihr könnt mir helfen.
Mfg Pumi
ich wollte gestern NeutroluxHD auf den Pingu draufmachen lief auch ganz gut, im Display hat er U LD angezeigt und danach kam 7 70.
Also hab alles nochmal von vorne gemacht nur jetzt zeigt er kein U LD mehr an sondern gleich 7 70 egal welchen Stick ich nehme.
Vorher hatte ich Neuprolux drauf.Da hat das installieren gleich beim 1. mal geklappt.
Als ich probiert habe Spark zu starten kommt boot und dann Load im Display und nichts passiert mehr.
Hier mal die Logs vom Reciever beim normalen starten:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 08 09
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCCTimed out
xyzModem - Cksum mode, 0(SOH)/0(STX)/0(CAN) packets, 20 retries
## Total Size = 0x00000000 = 0 Bytes
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
und beim Aufspielen des Rescue Images:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 08 09
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading spark/mImage
...............................................................................................................................................
5140251 bytes read
Un-Protect Flash Bank # 1
....................................................................................................................................... done
................................................................................................................ done
Erased 112 sectors
Copy to Flash...
danach passiert nichts mehr und es steht 5199 im Display.
Ziemlich langer Beitrag geworden,hoffe ihr könnt mir helfen.
Mfg Pumi