DM800se Sunray4

[bibo1]

hallo und guten Morgen,
ich habe nun seit zwei Tagen alle erdenklichen Images geflashed, für dm800se, sim210.
der Start des Flashens gelingt eigentlich Problemlos, aber.....
- nach dem Flash beim Neustart passieren folgende Dinge:
- läuft anfangs immer in den Stopmode mit IP und stopt natürlich
- nach eingen Restarts gehtes dann weiter meist bis zur Mitte des Fortschrittsbalkens, dann stop?
- nach weiteren Starts, geht es dann weiter nach gefühlten 15-20 Restarts läuft er durch und ich kann Konfigurationsangaben machen.
- Sendersuche auch kein Problem aber beim Umgang mit HD / USB stick green screen etc,etc.
das oben beschriebene gilt für alle getesteten Images!

Was kann ich noch wie machen? Ich weis nicht mehr weiter.

gruß
bibo1

 

[Karl-Hein]

AW: DM800se Sunray4

Mach das:


[FONT=&amp]Neu flashen[/FONT][FONT=&amp] mit SunrayFlashup + Bad Sector Repair (unter Extra- SunrayFlashup aktivieren) + Netzwerk (per LAN-Kabel mit dem Router verbinden) !

Wenn du alles richtig gemacht hast öffnet sich der "Flash-Button" in SunrayFlashup !

Jetzt sofort die Box IP (steht in SunrayFlashup ) in den IE und flashen !

----------------------------------
Box manuell neu booten!
----------------------------

Link ist nicht mehr aktiv.[/FONT]


Wenn das nicht hilft dann teste die Box mit einen anderen Netzteil ! Box hat noch Garantie ?

 

[bibo1]

AW: DM800se Sunray4

Hallo Karl-Hein,

Ich habe das jetzt laufende Image mit Bad Sector Repair des SunrayFlashup geflashed, das funtioniert ja ohne Probleme, hur beim Neustart gibt rs die o.a. Probs.Im Mom. Läuft das Image, aber nicht stabil.
Ich habe aber mit sunrayflasup durchgeflashed, nicht mit Browser, mit Browser die gleichen Probs.
Ich habe mir mal ne neue gebrauchte SIM210 bestellt. Probier mit der mal weiter und melde mich dann wieder.
Ob die Box noch Garantie hat muß ich noch klären.
zunächst einmal danke für die fixe Rückantwort

gruß
bibo1

 

[4gx35]

AW: DM800se Sunray4

mal anderes netzteil getestet, falls die box vorher korrekt lief?

 

[bibo1]

AW: DM800se Sunray4

hallo 4gx35,

ja ein anderes Netzteil schon getestet, ohne Erfolg.

 

[4gx35]

AW: DM800se Sunray4

dann hoffe ich mal, dass die andere simkarte hilft,
hatte außer netzteil eigentlich keine probleme mit dem clones, sogar alte 800hd laufen immer noch,
nur einmal funktionierte sofort hdmi nicht, box wurde problemlos getauscht

 

[chiefobrei]

AW: DM800se Sunray4

ja ein anderes Netzteil schon getestet, ohne Erfolg.

Startet die Box ohne Tuner?

 

[bibo1]

AW: DM800se Sunray4

hallo chiefobrei,

ohne Tuner probiert (ist nicht der Tripletuner drin, sondern BCM 4506).
wie schon beschrieben, manchmal nach etlichen Neustarts bootet er durch und funktioniert dann auch bedingt, d.h. beim Einrichten green screen oder bleibt stehen.
Zur Zeit habe ich ein NN2 stable lean eB sim2 v.4.0.11 bekomme es jedoch nicht gestartet. Der Bootmitschnitt sieht wie folgt aus:

[   15.159000] wrong type!
[   15.171000] set sb to 3(2)
[   15.171000] set fb to 2(-1)
[   15.172000] set input to 0
[   15.172000] set fb to 2(-1)
[   15.177000] bcm_video_analog_port_setup (fmt=7)
[   15.177000] SET FORMAT: display[1], format=7
[   15.178000] display 0 uses vbi path 1
[   15.178000] display 1 uses vbi path 0
[   15.179000] HDMI: now connected
[   15.181000] keys 81
[   15.208000] HDMI: EDID read ok
[   15.209000] HDMI: initial mode set!
[   15.209000] using 50.00Hz as MonitorRefreshRate
[   15.210000] SET FORMAT: display[0], format=37
[   15.210000] HDMI mode
[   15.211000] use EDID to detect colorspace
[   15.211000] using colorspace: 1
[   15.244000] HDMI: use logical CEC address 3
[   15.268000] set fb to 2(0)
[   15.268000] bcm_video_analog_port_setup (fmt=7)
[   15.268000] SET FORMAT: display[1], format=7
[   15.273000] disable wss on display 0
[   15.273000] disable wss on display 1
[   15.274000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R)
[   15.382000] CEC send ok!
[   15.410000] enable mad
[   15.453000] VIDEO0: set fallback framerate to 60000
[   15.454000] VIDEO0: set progressive override mode to 1
[   15.454000] VIDEO0: set streamtype!
[   15.455000] set MPEG2
[   15.455000] sw rave disabled!
[   15.459000] sync is off so we enable it
[   15.459000] playback!
[   15.460000] total video delay: 0 (0 ms)
[   15.463000] VIDEO0: start decode
[   15.464000] flush video decoder
[   15.464000] VIDEO0 got pts failed !!!! (ret 0)
[   16.861000] set ac3 to downmix
[   16.862000] set ac3plus to use_hdmi_caps
[   16.862000] set aac to downmix
[   16.863000] init ALSA!
[   16.893000] VIDEO0: first pts 0x0
[   16.922000] DVB: registering new adapter (BCM7405)
[   16.940000] autodetecting NIMs...
[   16.946000] ret: 2, feid: 13
[   16.946000] Found: Slot A, ID: 13 (by CA)
[   16.947000] Initializing adapter 0 (BCM4505-DVB-S2)
[   17.009000] bcm4506: found 4505, revision 0(b0)
[   17.009000] bcm4506: bcm_initAP
[   17.016000] bcm4506: upload & start firmware
[   17.043000] enable tsm0
[   19.059000] bcm4506: bcm4506: ap not running - start now
[   19.111000] bcm4506: uCode 0x61
[   19.129000] bcm4506: no bcm3445 detected
[   19.142000] i2c_enable_adc failed! -145
[   19.142000] DVB: registering adapter 0 frontend 0 (bcm4506)...
[   20.508000] VIDEO0: stop decode
[   20.509000] no decoder left in sync handling so disable xpt_sync
[   20.512000] registered vtuner misc/vtuner0, minor 56
[   20.513000] registered vtuner misc/vtuner1, minor 55
[   20.655000] VIDEO0: set blank to 0
[   20.656000] sync is off so we enable it
[   20.657000] playback!
[   20.657000] total video delay: 0 (0 ms)
[   20.661000] VIDEO0: start decode
[   20.662000] flush video decoder
[   20.693000] VIDEO0: first pts 0x0
[   20.693000] VIDEO0: framerate changed 3
[   20.693000] VIDEO0: resolution changed (1280 720)
[   20.694000] VIDEO0: aspect changed 3
[   20.713000] set current avs auto aspect to 16:9
[   20.713000] disable wss on display 0
[   20.714000] disable wss on display 1
[   20.714000] set current avs auto aspect to 16:9
[   20.715000] disable wss on display 0
[   20.715000] disable wss on display 1
[   20.716000] set sb to 3(1)
[   20.818000] VIDEO0: set blank to 0
[   20.819000] VIDEO0: stop decode
[   20.820000] VIDEO0: set blank to 0
[   20.820000] no decoder left in sync handling so disable xpt_sync
[   23.469000] Kernel panic - not syncing: Attempted to kill init!
[   23.470000] Rebooting in 180 seconds..
BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000004
WC1=FFFFFFEE
RC2=00000017
WC2=00000031
RC3=0000000D
WC3=FFFFFFE9
RC4=0000000D
WC4=00000031
NWC=0000000D
RC5=00000005
WC5=0000000D
RC6=00000016
WC6=0000000D
NRC=0000000D
RW=00000012
WW=00000049
G=00000000 R=0000000D W=0000000D
BL=00000000
RC1=00000002
RC2=00000015

BL=00000001
RC1=00000002
RC2=00000018

BL=00000002
RC1=00000004
RC2=00000014

BL=00000003
RC1=00000005
RC2=00000014

BL=00000004
RC1=00000002
RC2=00000011

BL=00000005
RC1=00000004
RC2=00000016

BL=00000006
RC1=00000003
RC2=00000015

BL=00000007
RC1=00000007
RC2=00000018
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800SE

FIRST STAGE 1.0/400 {BO23456}

2ND STAGE OK, build #84D(2011-09-01)

0.000  - BCM board setup
0.000  - fp init
0.000  - ca init
0.448  - load config
0.474  - config loaded.
 * press [S] to enter setup
OLED found!
color oled reset
lcd: BOOT #84D
P23 detected!
 - read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
 - failed to open /boot/secondstage.conf
 - failed to open /cf/autorun.bat
lcd: /boot/bootlogo-dm800se.elf.gz
bootlogo size: 35940
Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PA
best supported mode is 21
using 1920x1080i (60.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@sai>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-3.2-dm800se.gz
[    0.000000] Linux version 3.2-dm800se (newnigma2@nn2build.newnigma2.to) (gcc4
[    0.000000] Fetching vars from bootloader...
[    0.000000] Early serial console at MMIO32 0x10400b00 (options '1000000n8')
[    0.000000] bootconsole [uart0] enabled
[    0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 m1
[    0.000000] Using 256 MB RAM (from straps)
[    0.000000] Fetch var 'memsize' = '140'
[    0.000000] CPU revision is: 0002a044 (Brcm4380)
[    0.000000] FPU revision is: 00130001
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 10000000 @ 00000000 (usable)
[    0.000000] bmem: adding 134 MB LINUX region at 5 MB (0x0860a000@0x005f6000)
[    0.000000] bmem: adding 116 MB RESERVED region at 140 MB (0x07400000@0x08c0)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00010000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00010000
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat 8059e780, node_mem_map 8100000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65024 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768
[    0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pa4
[    0.000000] Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw conM
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[    0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64s
[    0.000000] Memory: 134932k/262144k available (4743k kernel code, 127212k re)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Measuring MIPS counter frequency...
[    0.000000] Detected MIPS clock frequency: 405 MHz (202.504 MHz counter)
[    0.000000] Console: colour dummy device 80x25
[    0.000000] Calibrating delay loop... 401.40 BogoMIPS (lpj=200704)
[    0.011000] pid_max: default: 32768 minimum: 301
[    0.012000] Mount-cache hash table entries: 512
[    0.014000] SMP: Booting CPU1...
[    0.015000] CPU revision is: 0002a044 (Brcm4380)
[    0.015000] FPU revision is: 00130001
[    0.015000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[    0.015000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64s
[    0.026000] SMP: CPU1 is running
[    0.026000] Brought up 2 CPUs
[    0.027000] devtmpfs: initialized
[    0.031000] NET: Registered protocol family 16
[    0.033000] PCI2.3->SDRAM window: 512 MB
[    0.040000] bio: create slab <bio-0> at 0
[    0.041000] SCSI subsystem initialized
[    0.042000] libata version 3.00 loaded.
[    0.042000] usbcore: registered new interface driver usbfs
[    0.043000] usbcore: registered new interface driver hub
[    0.043000] usbcore: registered new device driver usb
[    0.044000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[    0.045000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
[    0.046000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
[    0.046000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
[    0.047000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
[    0.048000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
[    0.049000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI)
[    0.050000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pre]
[    0.051000] Switching to clocksource upg
[    0.066000] NET: Registered protocol family 2
[    0.066000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.068000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.069000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.071000] TCP: Hash tables configured (established 8192 bind 8192)
[    0.071000] TCP reno registered
[    0.072000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.073000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.074000] NET: Registered protocol family 1
[    0.075000] RPC: Registered named UNIX socket transport module.
[    0.076000] RPC: Registered udp transport module.
[    0.076000] RPC: Registered tcp transport module.
[    0.077000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.078000] PCI: CLS 0 bytes, default 64
[    0.081000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.082000] JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.084000] SGI XFS with security attributes, large block/inode numbers, no d
[    0.086000] msgmni has been set to 263
[    0.088000] io scheduler noop registered
[    0.089000] io scheduler cfq registered (default)
[    0.090000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
ÿ[    0.112000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
[    0.113000] console [ttyS0] enabled, bootconsole disabled
[    0.113000] console [ttyS0] enabled, bootconsole disabled
[    0.134000] serial8250.0: ttyS1 at MMIO 0x10400b80 (irq = 67) is a 16550A
[    0.141000] loop: module loaded
[    0.142000] sata_brcmstb 0000:01:00.0: version 4.0
[    0.142000] brcm-pm: enabling sata clocks
[    0.143000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
[    0.143000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[    0.340000] scsi0 : sata_brcmstb
[    0.341000] scsi1 : sata_brcmstb
[    0.342000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
[    0.342000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
[    0.344000] Broadcom STB NAND controller (BrcmNand Controller)
[    0.345000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
[    0.349000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:)
[    0.350000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.350000] brcm-pm: enabling usb clocks
[    0.351000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[    0.352000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus numb1
[    0.384000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[    0.390000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[    0.391000] hub 1-0:1.0: USB hub found
[    0.391000] hub 1-0:1.0: 2 ports detected
[    0.392000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[    0.393000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus numb2
[    0.425000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
[    0.431000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[    0.432000] hub 2-0:1.0: USB hub found
[    0.432000] hub 2-0:1.0: 2 ports detected
[    0.433000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.434000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[    0.435000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus numb3
[    0.436000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[    0.501000] hub 3-0:1.0: USB hub found
[    0.502000] hub 3-0:1.0: 2 ports detected
[    0.503000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[    0.503000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus numb4
[    0.504000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
[    0.570000] hub 4-0:1.0: USB hub found
[    0.571000] hub 4-0:1.0: 2 ports detected
[    0.572000] Initializing USB Mass Storage driver...
[    0.572000] usbcore: registered new interface driver usb-storage
[    0.573000] USB Mass Storage support registered.
[    0.574000] i2c /dev entries driver
[    0.574000] ALSA device list:
[    0.575000]   No soundcards found.
[    0.575000] TCP cubic registered
[    0.576000] NET: Registered protocol family 17
[    0.576000] Registering the dns_resolver key type
[    0.577000] EBI CS1: setting up NAND flash (primary)
[    0.578000] mtd->oobsize=0, mtd->eccOobSize=0
[    0.579000] NAND_CS_NAND_XOR=00000000
[    0.579000] B4: NandSelect=40000202, nandConfig=04042300, chipSelect=1
[    0.580000] brcmnand_read_id: CS1: dev_id=ad76ad76
[    0.581000] After: NandSelect=40000202, nandConfig=04042300
[    0.581000] Block size=00004000, erase shift=14
[    0.582000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_e
[    0.583000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[    0.584000] timing1 not adjusted: 5363444f
[    0.584000] timing2 not adjusted: 00000fc6
[    0.585000] eccLevel=15, 1Ksector=0, oob=16
[    0.585000] nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
[    0.586000] <--brcmnand_set_acccontrol: acc b4: f7ff1010, after: f7ff1010
[    0.587000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB on CS1
[    0.588000]
[    0.588000] Found NAND on CS1: ACC=f7ff1010, cfg=04042300, flashId=ad76ad76,6
[    0.589000] BrcmNAND version = 0x0302 64MB @00000000
[    0.589000] B4: NandSelect=40000202, nandConfig=04042300, chipSelect=1
[    0.590000] brcmnand_read_id: CS1: dev_id=ad76ad76
[    0.591000] After: NandSelect=40000202, nandConfig=04042300
[    0.591000] Found NAND flash on Chip Select 1, chipSize=64MB, usable size=640
[    0.592000] brcmnand_scan: B4 nand_select = 40000202
[    0.593000] brcmnand_scan: After nand_select = 40000202
[    0.594000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shif4
[    0.594000] Brcm NAND controller version = 3.2 NAND flash size 64MB @1c000000
[    0.595000] brcmnand_scan:  mtd->oobsize=16
[    0.596000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[    0.597000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=3
[    0.598000] -->brcmnand_default_bbt
[    0.598000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[    0.599000] Bad block table Bbt0 found at page 0001ffe0, version 0x01 for ch1
[    0.600000] Bad block table 1tbB found at page 0001ffc0, version 0x01 for ch1
[    0.601000] brcmnandCET: Status -> Deferred
[    0.602000] Adjust partition complete size from 4000000 to 3f00000 to avoid e
[    0.603000] Adjust partition root size from 3c00000 to 3b00000 to avoid overe
[    0.604000] Creating 4 MTD partitions on "brcmnand.0":
[    0.605000] 0x000000000000-0x000003f00000 : "complete"
[    0.610000] 0x000000000000-0x000000040000 : "loader"
[    0.612000] 0x000000040000-0x000000400000 : "boot"
[    0.614000] 0x000000400000-0x000003f00000 : "root"
[    0.673000] ata1: SATA link down (SStatus 4 SControl 300)
[    0.706000] usb 1-1: new high-speed USB device number 2 using ehci-brcm
[    0.828000] scsi2 : usb-storage 1-1:1.0
[    0.999000] ata2: SATA link down (SStatus 4 SControl 300)
[    1.875000] scsi 2:0:0:0: Direct-Access              USB DISK 2.0     PMAP PS
[    2.454000] sd 2:0:0:0: [sda] 3915776 512-byte logical blocks: (2.00 GB/1.86)
[    2.457000] sd 2:0:0:0: [sda] Write Protect is off
[    2.457000] sd 2:0:0:0: [sda] Mode Sense: 23 00 00 00
[    2.459000] sd 2:0:0:0: [sda] No Caching mode page found
[    2.460000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    2.468000] sd 2:0:0:0: [sda] No Caching mode page found
[    2.468000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    2.494000]  sda: sda1
[    2.499000] sd 2:0:0:0: [sda] No Caching mode page found
[    2.500000] sd 2:0:0:0: [sda] Assuming drive cache: write through
[    2.501000] sd 2:0:0:0: [sda] Attached SCSI removable disk
[    8.273000] VFS: Mounted root (jffs2 filesystem) on device 31:3.
[    8.276000] devtmpfs: mounted
[    8.276000] Freeing unused kernel memory: 220k freed
INIT: version 2.88 booting
Displaying bootlogo.
Mounting squashfs images:loop mounting /squashfs-images/dreambox-dvb-modules-sqg
loop mounting /squashfs-images/qt4-embedded-core-sqsh-img to /media/squashfs-img
Starting udev
[   10.868000] udevd[94]: starting version 182
[   11.283000] stb_core: module license 'Proprietary' taints kernel.
[   11.284000] Disabling lock debugging due to kernel taint
[   14.616000] enter base init, xvd 20100413, vdc 20100413, rap 20100719, xpt 28
[   15.091000] 15:90007413 SMCA: controller reset timed out
[   15.101000] 15:100004810 SMCB: controller reset timed out
[   15.105000] register adapter
[   15.106000] register adapter
[   15.107000] register adapter
[   15.108000] register adapter
[   15.116000] FP Version 1
[   15.117000] input: dreambox front panel as /devices/virtual/input/input0
[   15.127000] 00, retry
[   15.127000] 00, retry
[   15.128000] 00, retry
[   15.128000] 00, retry
[   15.129000] 00, retry
[   15.129000] 00, retry
[   15.129000] 00, retry
[   15.130000] 00, retry
[   15.130000] 00, retry
[   15.131000] 00, retry
[   15.131000] 00, retry
[   15.131000] 00, retry
[   15.132000] 00, retry
[   15.132000] 00, retry
[   15.133000] 00, retry
[   15.133000] 00, retry
[   15.133000] 00, retry
[   15.134000] 00, retry
[   15.134000] 00, retry
[   15.135000] 00, retry
[   15.135000] 00, retry
[   15.135000] 00, retry
[   15.136000] 00, retry
[   15.136000] 00, retry
[   15.137000] 00, retry
[   15.137000] 00, retry
[   15.137000] 00, retry
[   15.138000] 00, retry
[   15.138000] 00, retry
[   15.139000] 00, retry
[   15.139000] 00, retry
[   15.139000] 00, retry
[   15.140000] signature: 00 00 00 00
[   15.141000] wrong type!
[   15.153000] set sb to 3(2)
[   15.153000] set fb to 2(-1)
[   15.154000] set input to 0
[   15.154000] set fb to 2(-1)
[   15.157000] bcm_video_analog_port_setup (fmt=7)
[   15.158000] SET FORMAT: display[1], format=7
[   15.158000] display 0 uses vbi path 1
[   15.159000] display 1 uses vbi path 0
[   15.160000] HDMI: now connected
[   15.162000] keys 81
[   15.189000] HDMI: EDID read ok
[   15.189000] HDMI: initial mode set!
[   15.190000] using 50.00Hz as MonitorRefreshRate
[   15.190000] SET FORMAT: display[0], format=37
[   15.191000] HDMI mode
[   15.191000] use EDID to detect colorspace
[   15.192000] using colorspace: 1
[   15.226000] HDMI: use logical CEC address 3
[   15.248000] set fb to 2(0)
[   15.248000] bcm_video_analog_port_setup (fmt=7)
[   15.249000] SET FORMAT: display[1], format=7
[   15.253000] disable wss on display 0
[   15.253000] disable wss on display 1
[   15.254000] bcmfb: creating surface with pixel format 0x07e48888 (BPXL_eA8_R)
[   15.364000] CEC send ok!
[   15.383000] enable mad
[   15.433000] VIDEO0: set fallback framerate to 60000
[   15.434000] VIDEO0: set progressive override mode to 1
[   15.434000] VIDEO0: set streamtype!
[   15.435000] set MPEG2
[   15.435000] sw rave disabled!
[   15.439000] sync is off so we enable it
[   15.439000] playback!
[   15.440000] total video delay: 0 (0 ms)
[   15.443000] VIDEO0: start decode
[   15.444000] flush video decoder
[   15.444000] VIDEO0 got pts failed !!!! (ret 0)
[   16.841000] set ac3 to downmix
[   16.842000] set ac3plus to use_hdmi_caps
[   16.842000] set aac to downmix
[   16.843000] init ALSA!
[   16.873000] VIDEO0: first pts 0x0
[   16.898000] DVB: registering new adapter (BCM7405)
[   16.911000] autodetecting NIMs...
[   16.912000] ret: 2, feid: 13
[   16.912000] Found: Slot A, ID: 13 (by CA)
[   16.913000] Initializing adapter 0 (BCM4505-DVB-S2)
[   16.966000] bcm4506: found 4505, revision 0(b0)
[   16.967000] bcm4506: bcm_initAP
[   16.973000] bcm4506: upload & start firmware
[   17.023000] enable tsm0
[   19.000000] bcm4506: bcm4506: ap not running - start now
[   19.052000] bcm4506: uCode 0x61
[   19.071000] bcm4506: no bcm3445 detected
[   19.084000] i2c_enable_adc failed! -145
[   19.084000] DVB: registering adapter 0 frontend 0 (bcm4506)...
[   20.451000] VIDEO0: stop decode
[   20.452000] no decoder left in sync handling so disable xpt_sync
[   20.455000] registered vtuner misc/vtuner0, minor 56
[   20.456000] registered vtuner misc/vtuner1, minor 55
[   20.591000] VIDEO0: set blank to 0
[   20.591000] sync is off so we enable it
[   20.592000] playback!
[   20.592000] total video delay: 0 (0 ms)
[   20.596000] VIDEO0: start decode
[   20.597000] flush video decoder
[   20.633000] VIDEO0: first pts 0x0
[   20.633000] VIDEO0: framerate changed 3
[   20.634000] VIDEO0: resolution changed (1280 720)
[   20.634000] VIDEO0: aspect changed 3
[   20.693000] set current avs auto aspect to 16:9
[   20.693000] disable wss on display 0
[   20.694000] disable wss on display 1
[   20.694000] set current avs auto aspect to 16:9
[   20.695000] disable wss on display 0
[   20.695000] disable wss on display 1
[   20.696000] set sb to 3(1)
[   20.753000] VIDEO0: set blank to 0
[   20.755000] VIDEO0: stop decode
[   20.755000] VIDEO0: set blank to 0
[   20.756000] no decoder left in sync handling so disable xpt_sync
[   23.324000] Kernel panic - not syncing: Attempted to kill init!
[   23.325000] Rebooting in 180 seconds..

vielleicht kann ja jemand etws daraus erkennen um der Ursache auf dem Grund zu kommen.

Gruß
bibo1
P.s. die Sim habe ich auch schon getauscht.

 

[bibo1]

AW: DM800se Sunray4

hallo,
kann niemand etwas zu dem o.a. Bootlog sagen? Oder sind vielleicht alle Mod`s in Urlaub? Urlaub ist Euch allemal gegönnt !!
:emoticon-0157-sun:
Gruß
bibo1

 

[bibo1]

AW: DM800se Sunray4

hallo Ihr Lieben,
da mir keiner weiterhelfen kann (bez. des o.a. Bootlogs-Mitschnitt) habe ich mir überlegt, ob man ein Image auf die Box bringt, dann mit meoboot oder Multiminiboot ein anderes Image, oder zwei einen USB bringt. Die Auswahl findet recht früh beim Bootvorgang statt, sodass der ganze Müll der ansonsten beim Starten des Flashenigmas passiert erst garnicht zu Tragen kommt. Macht das Sinn?
Oder kann man vielleicht ein Komplettimage direkt vom Stick laden und wenn ja wie?

Freue mich auf Antwort.
Gruß
bibo1

 

[ronallan22]

AW: DM800se Sunray4

Ich würde die Box reklamieren. Ich glaube dein Flash ist einfach kaputt.

 

[bibo1]

AW: DM800se Sunray4

ganau das vermute ich auch. Zur Reklamation ist es zu spät. Deshalb die Frage ob man den Speicherdefekt mittels Multiboot umgehen kann, oder ein Image direkt vom USB STIck starten kann?

Gruß
bibo1