Aktuelles Duck-Trick RAMFS Release **Support Thread**

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

da ist nur ne bootlog.log

Spoiler

<5>Linux version 2.6.32.59_stm24_0211 (server@192.168.178.22) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun May 18 12:55:42 CEST 2014
<5>Boot params:
<5>... MOUNT_ROOT_RDONLY - 00000001
<5>... RAMDISK_FLAGS - 00000000
<5>... ORIG_ROOT_DEV - 00000200
<5>... LOADER_TYPE - 00000000
<5>... INITRD_START - 00000000
<5>... INITRD_SIZE - 00000000
<5>Booting machvec: STb7100 Reference board
<4>Node 0: start_pfn = 0x4000, low = 0xc000
<4>Zone PFN ranges:
<4> Normal 0x00004000 -> 0x0000c000
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4> 0: 0x00004000 -> 0x0000c000
<7>On node 0 totalpages: 32768
<7>free_area_init_node: node 0, pgdat 84332788, node_mem_map 844eb000
<7> Normal zone: 256 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 32512 pages, LIFO batch:7
<4>Edision Argus Reference board initialisation
<6>STx7109 version 3.x
<6>Chip version 3.4
<6>Setting version to 4.0 to match commercial branding
<6>bpa2: partition 'LMI_VID' created at 0x10800000, size 90112 kB (0x05800000 B)
<6>bpa2: partition 'LMI_SYS' created at 0x045ec000, size 15360 kB (0x00f00000 B)
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
<5>Kernel command line: console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk
<6>PID hash table entries: 512 (order: -1, 2048 bytes)
<6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>PVR=04061100 CVR=30480000 PRR=00009300
<5>I-cache : n_ways=2 n_sets=256 way_incr=8192
<5>I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
<5>D-cache : n_ways=2 n_sets=512 way_incr=16384
<5>D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
<6>Memory: 109396k/131072k available (2502k kernel code, 770k data, 1604k init)
<6>Hierarchical RCU implementation.
<6>NR_IRQS:600
<6>console [ttyAS0] enabled
<6>sh_tmu: TMU0 used for clock events
<6>sh_tmu: TMU0 used for periodic clock events
<6>sh_tmu: TMU1 used as clock source
<6>Calibrating delay loop... 264.60 BogoMIPS (lpj=1323008)
<4>Mount-cache hash table entries: 512
<4>CPU: STx7109
<6>NET: Registered protocol family 16
<4>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>Generic PHY: Registered new driver (0xffffffff)
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<5>DMA: Registering DMA API.
<6>Switching to clocksource TMU1
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
<6>ROMFS MTD (C) 2007 Red Hat, Inc.
<6>msgmni has been set to 213
<6>alg: No test for stdrng (krng)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered (default)
<6>lirc_dev: IR Remote Control driver registered, major 61
<6>STMicroelectronics ASC driver initialized
<6>stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
<6>stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
<6>loop: module loaded
<7>sata-stm version 0.8
<7>sata-stm using hardware scatter/gather
<7>sata-stm SATA version 1.00 DMA version 2.02
<6>MiPHY driver style MiPHY-DUMMY probed successfully
<6>MiPHY-DUMMY, c0.0 Claimed by sata-stm
<6>scsi0 : sata-stm
<6>ata1: SATA max UDMA/133 irq 170
<5>physmap platform flash device: 00800000 at 00000000
<6>physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
<4> Amd/Fujitsu Extended Query Table at 0x0040
<4>physmap-flash: Swapping erase regions for broken CFI table.
<5>number of CFI chips: 1
<5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
<5>cmdlinepart partition parsing not available
<5>Searching for RedBoot partition table in physmap-flash at offset 0x7f0000
<5>No RedBoot partition table detected in physmap-flash
<5>Using physmap partition information
<5>Creating 4 MTD partitions on "physmap-flash":
<5>0x000000000000-0x000000040000 : "Boot (RO)"
<5>0x000000040000-0x0000006a0000 : "jffs2 (RW)"
<5>0x000000700000-0x000000800000 : "NAND-END (RO)"
<5>0x000000000000-0x000000800000 : "Kompletter Nand Flash (RW) - Loeschen ohne neue Firmware - JTAG noetig"
<5>slram: not enough parameters.
<6>STe100p: Registered new driver (0x1c040011)
<6>STe101p: Registered new driver (0x00061c50)
<6> DWMAC100
<6> No HW DMA feature register supported
<6> Normal descriptors
<6>nwhw_config: (eth0) setting mac address: 00:80:e1:12:06:30
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<4>stm_usb_probe: usb_48_clk clock not found for stm-usb.0
<4>stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
<6>ata1: SATA link down (SStatus 0 SControl 0)
<6>stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
<6>stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
<6>stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
<6>stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<6>stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
<6>stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
<6>stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>i2c /dev entries driver
<6>i2c_st40_pio: ST40 PIO based I2C Driver for STM24
<6>Linux video capture interface: v2.00
<6>sh_tmu: TMU0 kept as earlytimer
<6>sh_tmu: TMU1 kept as earlytimer
<4>STMicroelectronics - Coprocessors st231 Init
<4>st231.0 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0000000 size 0x00400000
<4> cop. addr 0x10000000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<4>st231.1 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0400000 size 0x00400000
<4> cop. addr 0x10400000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<6>DMA: Registering fdma_dmac handler (16 channels).
<4>IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
<6>stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
<6>platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.5
<6>Advanced Linux Sound Architecture Driver Version 1.0.21.
<6>ALSA device list:
<6> #0: STMicroelectronics STx7109 cut 4.0 SOC audio subsystem
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<4>Freeing unused kernel memory: 1604k freed
<6>usb 1-1: new high speed USB device using stm-ehci and address 2
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>scsi1 : SCSI emulation for USB Mass Storage devices
<7>usb-storage: device found at 2
<4>usb-storage: wait 0 seconds on usb port 1
<5>scsi 1:0:0:0: Direct-Access USB 2.0 Flash Disk 5.00 PQ: 0 ANSI: 2
<5>sd 1:0:0:0: [sda] 8167424 512-byte logical blocks: (4.18 GB/3.89 GiB)
<7>usb-storage: device scan complete
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<6> sda: sda1 sda2 sda3 sda4
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<5>sd 1:0:0:0: [sda] Attached SCSI removable disk
<4>Fulan front panel driver
<4>YWPANEL_VFD_DETECT: Frontcontroller I2C: 02:28 @2672
<4>YWPANEL_VFD_DETECT: result=1, vfd_type=2
<4>VfdType = 2
<4>YWPANEL_VFD_Init: YWPANEL_VFD_Initialize(): 0 @2849
<4>CpuType = -2077833128
<4>DisplayInfo = 0
<4>scankeyNum = 160
<4>swMajorVersion = 8
<4>swSubVersion = 193
<6>input: fulan front panel buttons as /devices/virtual/input/input0
<3>aotom_vip1: exports duplicate symbol I2C_bus_add (owned by aotom)
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>EXT2-fs: sda2: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda2): recovery complete
<6>EXT4-fs (sda2): mounted filesystem with ordered data mode
<4>EXT2-fs: sda4: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda4): recovery complete
<6>EXT4-fs (sda4): mounted filesystem with ordered data mode
<5>Slow work thread pool: Starting up
<5>Slow work thread pool: Ready
<6>snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
<6>pseudocard: 1 pseudo soundcard(s) found
<4>pti: module license 'NO' taints kernel.
<4>Disabling lock debugging due to kernel taint
<6>DVB: registering new adapter (STM Streamer)
<4>DVB: registering adapter 0 frontend 0 (Sharp7306 Plug&Play (VIP1v2) )...
<6>input: TDT RC event driver as /devices/virtual/input/input1
<6>lirc_dev: lirc_register_driver: sample_rate: 0
<6>Adding 67972k swap on /dev/sda3. Priority:-1 extents:1 across:67972k
<4>eth0: device MAC address 00:80:e1:12:06:30
<6>STMMAC MII Bus: probed
<6>eth0: PHY ID 0181b8a0 at 2 IRQ 11 (0:02) active
<6>stmmac_timer: (eth0) sh_tmu Timer (freq 256Hz)
<6> No MAC Management Counters available
<6>PHY: 0:02 - Link is Up - 100/Half
<4>LED level = 1
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = 8b028000
<1>[0000000c] *pgd=00000000
<4>Oops: 0000 [#1]
<0>last sysfs file: /sys/devices/platform/snd_pseudo.0/firmware/snd_pseudo.0/loading
<4>Modules linked in: smartcard lirc_stm simu_button platform stmalloc sth264pp player2 stmdvb stmsysfs stm_monitor pti(P) cimax fe_core_vip1v2 pseudocard stmvbi stmvout stm_v4l2 p2div64 pcm_transcoder silencegen kreplay ksound mpeg2hw mmelog avs mme_host embxshm embxmailbox embxshell stmfb stmcore_display_stx7109c3 autofs4 nls_utf8 nls_koi8_u nls_koi8_r nls_iso8859_5 nls_iso8859_2 nls_iso8859_1 nls_cp866 nls_cp855 nls_cp850 nls_cp437 nls_cp1251 nls_cp1250 nls_ascii jbd cachefiles cifs vfat udf ntfs msdos isofs fscache fat e2_proc cpu_frequ aotom
<4>
<4>Pid : 1019, Comm: enigma2
<4>CPU : 0 Tainted: P (2.6.32.59_stm24_0211 #1)
<4>
<4>PC : 841c7eb4 SP : 8bec9ef4 SR : 40008000 TEA : c1080888
<4>R0 : 00000001 R1 : 0000000c R2 : 00143000 R3 : 84012528
<4>R4 : 00000000 R5 : 00000000 R6 : ffffffff R7 : ffffffff
<4>R8 : 841c7eb0 R9 : c1080de8 R10 : 84118aa2 R11 : c0425afe
<4>R12 : fffffff7 R13 : 2b46f048 R14 : 00000000
<4>MACH: 0000052a MACL: b5c50000 GBR : 2b46f928 PR : c107e11e
<4>
<4>Call trace:
<4> [<c107f212>] 0xc107f212
<4> [<84069112>] 0x84069112
<4> [<84069a22>] 0x84069a22
<4> [<84071316>] 0x84071316
<4> [<8406ffb4>] 0x8406ffb4
<4> [<8405d32e>] 0x8405d32e
<4> [<84069aaa>] 0x84069aaa
<4> [<84007920>] 0x84007920
<4> [<84069a7c>] 0x84069a7c
<4>
<4>Process: enigma2 (pid: 1019, stack limit = 8bec8001)
<4>Stack: (0x8bec9ef4 to 0x8beca000)
<4>9ee0: c107f212 2b46eefe fffffff2
<4>9f00: c0425afe 84309038 84069112 c0425afe 2b46eefe 8bd8e9c0 00000001 84069a22
<4>9f20: 8bd8e9c0 2b46eefe 8bd8e9c0 ffffffff 84071316 8b80ff20 fffe2cb3 8406ffb4
<4>9f40: 00000013 00008002 00000000 8bd8e9c0 00000000 8b85bd60 8b437050 00000002
<4>9f60: 8405d32e 00000000 00000000 84069aaa 2b46f048 fffffff7 c0425afe 2b46eefe
<4>9f80: 00000013 8bd8e9c0 00000001 84007920 0000059c 00000000 00000071 00000100
<4>9fa0: 84069a7c 00461244 00461244 2b46f534 00000036 00000013 c0425afe 2b46eefe
<4>9fc0: 2b46f53c 2b46ef4c 00000001 29f3f4b4 00000000 29f52038 2b46f048 00000000
<4>9fe0: 2b46eefc 2a23c524 00488018 00000000 2b46f928 00000003 00000090 0000004c
<4>---[ end trace da319361ec522b1e ]---

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

jo da ist bei dir der aotom display treiber abgestürzt, das sieht mir nach dem hdmi Pio pin aus der anscheinend bei dir nicht gesetzt wurde, deshallb passiert da auch nix mehr, starte mal bitte nochmal neu

Das ist nen Vip1 den du daverwendest oder ?
wenn das wiedr passiert poste bitte mal die ausgabe von

cat /proc/stpio

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

es bleibt leider dabei

Spoiler

<5>Linux version 2.6.32.59_stm24_0211 (server@192.168.178.22) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun May 18 12:55:42 CEST 2014
<5>Boot params:
<5>... MOUNT_ROOT_RDONLY - 00000001
<5>... RAMDISK_FLAGS - 00000000
<5>... ORIG_ROOT_DEV - 00000200
<5>... LOADER_TYPE - 00000000
<5>... INITRD_START - 00000000
<5>... INITRD_SIZE - 00000000
<5>Booting machvec: STb7100 Reference board
<4>Node 0: start_pfn = 0x4000, low = 0xc000
<4>Zone PFN ranges:
<4> Normal 0x00004000 -> 0x0000c000
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4> 0: 0x00004000 -> 0x0000c000
<7>On node 0 totalpages: 32768
<7>free_area_init_node: node 0, pgdat 84332788, node_mem_map 844eb000
<7> Normal zone: 256 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 32512 pages, LIFO batch:7
<4>Edision Argus Reference board initialisation
<6>STx7109 version 3.x
<6>Chip version 3.4
<6>Setting version to 4.0 to match commercial branding
<6>bpa2: partition 'LMI_VID' created at 0x10800000, size 90112 kB (0x05800000 B)
<6>bpa2: partition 'LMI_SYS' created at 0x045ec000, size 15360 kB (0x00f00000 B)
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
<5>Kernel command line: console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk
<6>PID hash table entries: 512 (order: -1, 2048 bytes)
<6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>PVR=04061100 CVR=30480000 PRR=00009300
<5>I-cache : n_ways=2 n_sets=256 way_incr=8192
<5>I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
<5>D-cache : n_ways=2 n_sets=512 way_incr=16384
<5>D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
<6>Memory: 109396k/131072k available (2502k kernel code, 770k data, 1604k init)
<6>Hierarchical RCU implementation.
<6>NR_IRQS:600
<6>console [ttyAS0] enabled
<6>sh_tmu: TMU0 used for clock events
<6>sh_tmu: TMU0 used for periodic clock events
<6>sh_tmu: TMU1 used as clock source
<6>Calibrating delay loop... 264.60 BogoMIPS (lpj=1323008)
<4>Mount-cache hash table entries: 512
<4>CPU: STx7109
<6>NET: Registered protocol family 16
<4>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>Generic PHY: Registered new driver (0xffffffff)
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<5>DMA: Registering DMA API.
<6>Switching to clocksource TMU1
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
<6>ROMFS MTD (C) 2007 Red Hat, Inc.
<6>msgmni has been set to 213
<6>alg: No test for stdrng (krng)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered (default)
<6>lirc_dev: IR Remote Control driver registered, major 61
<6>STMicroelectronics ASC driver initialized
<6>stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
<6>stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
<6>loop: module loaded
<7>sata-stm version 0.8
<7>sata-stm using hardware scatter/gather
<7>sata-stm SATA version 1.00 DMA version 2.02
<6>MiPHY driver style MiPHY-DUMMY probed successfully
<6>MiPHY-DUMMY, c0.0 Claimed by sata-stm
<6>scsi0 : sata-stm
<6>ata1: SATA max UDMA/133 irq 170
<5>physmap platform flash device: 00800000 at 00000000
<6>physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
<4> Amd/Fujitsu Extended Query Table at 0x0040
<4>physmap-flash: Swapping erase regions for broken CFI table.
<5>number of CFI chips: 1
<5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
<5>cmdlinepart partition parsing not available
<5>Searching for RedBoot partition table in physmap-flash at offset 0x7f0000
<5>No RedBoot partition table detected in physmap-flash
<5>Using physmap partition information
<5>Creating 4 MTD partitions on "physmap-flash":
<5>0x000000000000-0x000000040000 : "Boot (RO)"
<5>0x000000040000-0x0000006a0000 : "jffs2 (RW)"
<5>0x000000700000-0x000000800000 : "NAND-END (RO)"
<5>0x000000000000-0x000000800000 : "Kompletter Nand Flash (RW) - Loeschen ohne neue Firmware - JTAG noetig"
<5>slram: not enough parameters.
<6>STe100p: Registered new driver (0x1c040011)
<6>STe101p: Registered new driver (0x00061c50)
<6> DWMAC100
<6> No HW DMA feature register supported
<6> Normal descriptors
<6>nwhw_config: (eth0) setting mac address: 00:80:e1:12:06:30
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<4>stm_usb_probe: usb_48_clk clock not found for stm-usb.0
<4>stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
<6>ata1: SATA link down (SStatus 0 SControl 0)
<6>stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
<6>stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
<6>stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
<6>stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<6>stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
<6>stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
<6>stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>i2c /dev entries driver
<6>i2c_st40_pio: ST40 PIO based I2C Driver for STM24
<6>Linux video capture interface: v2.00
<6>sh_tmu: TMU0 kept as earlytimer
<6>sh_tmu: TMU1 kept as earlytimer
<4>STMicroelectronics - Coprocessors st231 Init
<4>st231.0 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0000000 size 0x00400000
<4> cop. addr 0x10000000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<4>st231.1 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0400000 size 0x00400000
<4> cop. addr 0x10400000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<6>DMA: Registering fdma_dmac handler (16 channels).
<4>IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
<6>stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
<6>platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.5
<6>Advanced Linux Sound Architecture Driver Version 1.0.21.
<6>ALSA device list:
<6> #0: STMicroelectronics STx7109 cut 4.0 SOC audio subsystem
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<4>Freeing unused kernel memory: 1604k freed
<6>usb 1-1: new high speed USB device using stm-ehci and address 2
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>scsi1 : SCSI emulation for USB Mass Storage devices
<7>usb-storage: device found at 2
<4>usb-storage: wait 0 seconds on usb port 1
<5>scsi 1:0:0:0: Direct-Access USB 2.0 Flash Disk 5.00 PQ: 0 ANSI: 2
<5>sd 1:0:0:0: [sda] 8167424 512-byte logical blocks: (4.18 GB/3.89 GiB)
<7>usb-storage: device scan complete
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<6> sda: sda1 sda2 sda3 sda4
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<5>sd 1:0:0:0: [sda] Attached SCSI removable disk
<4>Fulan front panel driver
<4>YWPANEL_VFD_DETECT: Frontcontroller I2C: 02:28 @2672
<4>YWPANEL_VFD_DETECT: result=1, vfd_type=2
<4>VfdType = 2
<4>YWPANEL_VFD_Init: YWPANEL_VFD_Initialize(): 0 @2849
<4>CpuType = -2077833128
<4>DisplayInfo = 0
<4>scankeyNum = 160
<4>swMajorVersion = 8
<4>swSubVersion = 193
<6>input: fulan front panel buttons as /devices/virtual/input/input0
<3>aotom_vip1: exports duplicate symbol I2C_bus_add (owned by aotom)
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>EXT2-fs: sda2: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda2): recovery complete
<6>EXT4-fs (sda2): mounted filesystem with ordered data mode
<4>EXT2-fs: sda4: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda4): recovery complete
<6>EXT4-fs (sda4): mounted filesystem with ordered data mode
<5>Slow work thread pool: Starting up
<5>Slow work thread pool: Ready
<6>snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
<6>pseudocard: 1 pseudo soundcard(s) found
<4>pti: module license 'NO' taints kernel.
<4>Disabling lock debugging due to kernel taint
<6>DVB: registering new adapter (STM Streamer)
<4>DVB: registering adapter 0 frontend 0 (Sharp7306 Plug&Play (VIP1v2) )...
<6>input: TDT RC event driver as /devices/virtual/input/input1
<6>lirc_dev: lirc_register_driver: sample_rate: 0
<6>Adding 67972k swap on /dev/sda3. Priority:-1 extents:1 across:67972k
<4>eth0: device MAC address 00:80:e1:12:06:30
<6>STMMAC MII Bus: probed
<6>eth0: PHY ID 0181b8a0 at 2 IRQ 11 (0:02) active
<6>stmmac_timer: (eth0) sh_tmu Timer (freq 256Hz)
<6> No MAC Management Counters available
<6>PHY: 0:02 - Link is Up - 100/Half
<4>LED level = 1
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = 8b153000
<1>[0000000c] *pgd=00000000
<4>Oops: 0000 [#1]
<0>last sysfs file: /sys/devices/platform/snd_pseudo.0/firmware/snd_pseudo.0/loading
<4>Modules linked in: smartcard lirc_stm simu_button platform stmalloc sth264pp player2 stmdvb stmsysfs stm_monitor pti(P) cimax fe_core_vip1v2 pseudocard stmvbi stmvout stm_v4l2 p2div64 pcm_transcoder silencegen kreplay ksound mpeg2hw mmelog avs mme_host embxshm embxmailbox embxshell stmfb stmcore_display_stx7109c3 autofs4 nls_utf8 nls_koi8_u nls_koi8_r nls_iso8859_5 nls_iso8859_2 nls_iso8859_1 nls_cp866 nls_cp855 nls_cp850 nls_cp437 nls_cp1251 nls_cp1250 nls_ascii jbd cachefiles cifs vfat udf ntfs msdos isofs fscache fat e2_proc cpu_frequ aotom
<4>
<4>Pid : 1018, Comm: enigma2
<4>CPU : 0 Tainted: P (2.6.32.59_stm24_0211 #1)
<4>
<4>PC : 841c7eb4 SP : 8ba4def4 SR : 40008000 TEA : c1080888
<4>R0 : 00000001 R1 : 0000000c R2 : 00143000 R3 : 84012528
<4>R4 : 00000000 R5 : 00000000 R6 : ffffffff R7 : ffffffff
<4>R8 : 841c7eb0 R9 : c1080de8 R10 : 84118aa2 R11 : c0425afe
<4>R12 : fffffff7 R13 : 2b46f048 R14 : 00000000
<4>MACH: 0000052a MACL: b5c50000 GBR : 2b46f928 PR : c107e11e
<4>
<4>Call trace:
<4> [<c107f212>] 0xc107f212
<4> [<84069112>] 0x84069112
<4> [<84069a22>] 0x84069a22
<4> [<8406ffb4>] 0x8406ffb4
<4> [<8405d32e>] 0x8405d32e
<4> [<84069aaa>] 0x84069aaa
<4> [<84007920>] 0x84007920
<4> [<84069a7c>] 0x84069a7c
<4>
<4>Process: enigma2 (pid: 1018, stack limit = 8ba4c001)
<4>Stack: (0x8ba4def4 to 0x8ba4e000)
<4>dee0: c107f212 2b46eefe fffffff2
<4>df00: c0425afe 37fc2f62 84069112 c0425afe 2b46eefe 8b36c4a0 00000001 84069a22
<4>df20: 8b36c4a0 2b46eefe 8b36c4a0 000000a8 c17d2898 00000000 00000000 8406ffb4
<4>df40: 00000014 00008002 00000000 8b36c4a0 00000000 8b85bd60 8b5a7050 00000002
<4>df60: 8405d32e 00000000 00000000 84069aaa 2b46f048 fffffff7 c0425afe 2b46eefe
<4>df80: 00000014 8b36c4a0 00000001 84007920 0000059c 00000000 00000071 00000100
<4>dfa0: 84069a7c 00461244 00461244 2b46f534 00000036 00000014 c0425afe 2b46eefe
<4>dfc0: 2b46f53c 2b46ef4c 00000001 29f3f4b4 00000000 29f52038 2b46f048 00000000
<4>dfe0: 2b46eefc 2a23c524 00488018 00000000 2b46f928 00000003 00000090 0000004c
<4>---[ end trace 9190661e372836fc ]---

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

poste mir mla bitte das cat /proc/stpio, hab das bei mir am vip1v1 ja auch am laufen so

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ich hab nen vip1v2 und in der datei steht nix drin

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ok moment wenn das der vip1v2 ist dann nutzt der das aotom vom vip2, da sollte der pio garnicht drin sein , warte mal ich poste gleich nochmal

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ok ich verstehe zwar nicht warum der Display treiber dabei abstürzt da das ne standart funktion dessen ist, aber ich hab das jetzt mal deaktiviert , führe das update nun nochmal peer terminal aus, geb dafür folgende 4 befehler der reihe nach ein

echo 142 > /var/config/update/version
/var/config/updatecheck.sh
sync
init 6

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

das selbe wie vorher

Spoiler

<5>Linux version 2.6.32.59_stm24_0211 (server@192.168.178.22) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun May 18 12:55:42 CEST 2014
<5>Boot params:
<5>... MOUNT_ROOT_RDONLY - 00000001
<5>... RAMDISK_FLAGS - 00000000
<5>... ORIG_ROOT_DEV - 00000200
<5>... LOADER_TYPE - 00000000
<5>... INITRD_START - 00000000
<5>... INITRD_SIZE - 00000000
<5>Booting machvec: STb7100 Reference board
<4>Node 0: start_pfn = 0x4000, low = 0xc000
<4>Zone PFN ranges:
<4> Normal 0x00004000 -> 0x0000c000
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4> 0: 0x00004000 -> 0x0000c000
<7>On node 0 totalpages: 32768
<7>free_area_init_node: node 0, pgdat 84332788, node_mem_map 844eb000
<7> Normal zone: 256 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 32512 pages, LIFO batch:7
<4>Edision Argus Reference board initialisation
<6>STx7109 version 3.x
<6>Chip version 3.4
<6>Setting version to 4.0 to match commercial branding
<6>bpa2: partition 'LMI_VID' created at 0x10800000, size 90112 kB (0x05800000 B)
<6>bpa2: partition 'LMI_SYS' created at 0x045ec000, size 15360 kB (0x00f00000 B)
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
<5>Kernel command line: console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk
<6>PID hash table entries: 512 (order: -1, 2048 bytes)
<6>Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
<6>Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>PVR=04061100 CVR=30480000 PRR=00009300
<5>I-cache : n_ways=2 n_sets=256 way_incr=8192
<5>I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
<5>D-cache : n_ways=2 n_sets=512 way_incr=16384
<5>D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
<6>Memory: 109396k/131072k available (2502k kernel code, 770k data, 1604k init)
<6>Hierarchical RCU implementation.
<6>NR_IRQS:600
<6>console [ttyAS0] enabled
<6>sh_tmu: TMU0 used for clock events
<6>sh_tmu: TMU0 used for periodic clock events
<6>sh_tmu: TMU1 used as clock source
<6>Calibrating delay loop... 264.60 BogoMIPS (lpj=1323008)
<4>Mount-cache hash table entries: 512
<4>CPU: STx7109
<6>NET: Registered protocol family 16
<4>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<7>libata version 3.00 loaded.
<6>Generic PHY: Registered new driver (0xffffffff)
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<5>DMA: Registering DMA API.
<6>Switching to clocksource TMU1
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 4096 (order: 3, 32768 bytes)
<6>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
<6>TCP: Hash tables configured (established 4096 bind 4096)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
<6>ROMFS MTD (C) 2007 Red Hat, Inc.
<6>msgmni has been set to 213
<6>alg: No test for stdrng (krng)
<6>io scheduler noop registered
<6>io scheduler anticipatory registered (default)
<6>lirc_dev: IR Remote Control driver registered, major 61
<6>STMicroelectronics ASC driver initialized
<6>stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
<6>stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
<6>loop: module loaded
<7>sata-stm version 0.8
<7>sata-stm using hardware scatter/gather
<7>sata-stm SATA version 1.00 DMA version 2.02
<6>MiPHY driver style MiPHY-DUMMY probed successfully
<6>MiPHY-DUMMY, c0.0 Claimed by sata-stm
<6>scsi0 : sata-stm
<6>ata1: SATA max UDMA/133 irq 170
<5>physmap platform flash device: 00800000 at 00000000
<6>physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
<4> Amd/Fujitsu Extended Query Table at 0x0040
<4>physmap-flash: Swapping erase regions for broken CFI table.
<5>number of CFI chips: 1
<5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
<5>cmdlinepart partition parsing not available
<5>Searching for RedBoot partition table in physmap-flash at offset 0x7f0000
<5>No RedBoot partition table detected in physmap-flash
<5>Using physmap partition information
<5>Creating 4 MTD partitions on "physmap-flash":
<5>0x000000000000-0x000000040000 : "Boot (RO)"
<5>0x000000040000-0x0000006a0000 : "jffs2 (RW)"
<5>0x000000700000-0x000000800000 : "NAND-END (RO)"
<5>0x000000000000-0x000000800000 : "Kompletter Nand Flash (RW) - Loeschen ohne neue Firmware - JTAG noetig"
<5>slram: not enough parameters.
<6>STe100p: Registered new driver (0x1c040011)
<6>STe101p: Registered new driver (0x00061c50)
<6> DWMAC100
<6> No HW DMA feature register supported
<6> Normal descriptors
<6>nwhw_config: (eth0) setting mac address: 00:80:e1:12:06:30
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<4>stm_usb_probe: usb_48_clk clock not found for stm-usb.0
<4>stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
<6>ata1: SATA link down (SStatus 0 SControl 0)
<6>stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
<6>stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
<6>stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
<6>stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<6>stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
<6>stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
<6>stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 1 port detected
<6>Initializing USB Mass Storage driver...
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>i2c /dev entries driver
<6>i2c_st40_pio: ST40 PIO based I2C Driver for STM24
<6>Linux video capture interface: v2.00
<6>sh_tmu: TMU0 kept as earlytimer
<6>sh_tmu: TMU1 kept as earlytimer
<4>STMicroelectronics - Coprocessors st231 Init
<4>st231.0 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0000000 size 0x00400000
<4> cop. addr 0x10000000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<4>st231.1 Coprocessor -------------------------------------------
<4> flags 0001 RAM start at 0xb0400000 size 0x00400000
<4> cop. addr 0x10400000
<4> Channels : Not defined
<4> IRQ : not used
<4>---------------------------------------------------------------
<6>DMA: Registering fdma_dmac handler (16 channels).
<4>IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
<6>stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
<6>platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.5
<6>Advanced Linux Sound Architecture Driver Version 1.0.21.
<6>ALSA device list:
<6> #0: STMicroelectronics STx7109 cut 4.0 SOC audio subsystem
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<4>Freeing unused kernel memory: 1604k freed
<6>usb 1-1: new high speed USB device using stm-ehci and address 2
<6>usb 1-1: configuration #1 chosen from 1 choice
<6>scsi1 : SCSI emulation for USB Mass Storage devices
<7>usb-storage: device found at 2
<4>usb-storage: wait 0 seconds on usb port 1
<5>scsi 1:0:0:0: Direct-Access USB 2.0 Flash Disk 5.00 PQ: 0 ANSI: 2
<5>sd 1:0:0:0: [sda] 8167424 512-byte logical blocks: (4.18 GB/3.89 GiB)
<7>usb-storage: device scan complete
<5>sd 1:0:0:0: [sda] Write Protect is off
<7>sd 1:0:0:0: [sda] Mode Sense: 0b 00 00 08
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<6> sda: sda1 sda2 sda3 sda4
<3>sd 1:0:0:0: [sda] Assuming drive cache: write through
<5>sd 1:0:0:0: [sda] Attached SCSI removable disk
<4>Fulan front panel driver
<4>YWPANEL_VFD_DETECT: Frontcontroller I2C: 02:28 @2672
<4>YWPANEL_VFD_DETECT: result=1, vfd_type=2
<4>VfdType = 2
<4>YWPANEL_VFD_Init: YWPANEL_VFD_Initialize(): 0 @2849
<4>CpuType = -2077833128
<4>DisplayInfo = 0
<4>scankeyNum = 160
<4>swMajorVersion = 8
<4>swSubVersion = 193
<6>input: fulan front panel buttons as /devices/virtual/input/input0
<3>aotom_vip1: exports duplicate symbol I2C_bus_add (owned by aotom)
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>fsck.ext2: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>tune2fs: sending ioctl 127c to a partition!
<4>EXT2-fs: sda2: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda2): recovery complete
<6>EXT4-fs (sda2): mounted filesystem with ordered data mode
<4>EXT2-fs: sda4: couldn't mount because of unsupported optional features (244).
<6>EXT4-fs (sda4): recovery complete
<6>EXT4-fs (sda4): mounted filesystem with ordered data mode
<5>Slow work thread pool: Starting up
<5>Slow work thread pool: Ready
<6>snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
<6>pseudocard: 1 pseudo soundcard(s) found
<4>pti: module license 'NO' taints kernel.
<4>Disabling lock debugging due to kernel taint
<6>DVB: registering new adapter (STM Streamer)
<4>DVB: registering adapter 0 frontend 0 (Sharp7306 Plug&Play (VIP1v2) )...
<6>input: TDT RC event driver as /devices/virtual/input/input1
<6>lirc_dev: lirc_register_driver: sample_rate: 0
<6>Adding 67972k swap on /dev/sda3. Priority:-1 extents:1 across:67972k
<4>eth0: device MAC address 00:80:e1:12:06:30
<6>STMMAC MII Bus: probed
<6>eth0: PHY ID 0181b8a0 at 2 IRQ 11 (0:02) active
<6>stmmac_timer: (eth0) sh_tmu Timer (freq 256Hz)
<6> No MAC Management Counters available
<6>PHY: 0:02 - Link is Up - 100/Half
<4>LED level = 1
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = 8b153000
<1>[0000000c] *pgd=00000000
<4>Oops: 0000 [#1]
<0>last sysfs file: /sys/devices/platform/snd_pseudo.0/firmware/snd_pseudo.0/loading
<4>Modules linked in: smartcard lirc_stm simu_button platform stmalloc sth264pp player2 stmdvb stmsysfs stm_monitor pti(P) cimax fe_core_vip1v2 pseudocard stmvbi stmvout stm_v4l2 p2div64 pcm_transcoder silencegen kreplay ksound mpeg2hw mmelog avs mme_host embxshm embxmailbox embxshell stmfb stmcore_display_stx7109c3 autofs4 nls_utf8 nls_koi8_u nls_koi8_r nls_iso8859_5 nls_iso8859_2 nls_iso8859_1 nls_cp866 nls_cp855 nls_cp850 nls_cp437 nls_cp1251 nls_cp1250 nls_ascii jbd cachefiles cifs vfat udf ntfs msdos isofs fscache fat e2_proc cpu_frequ aotom
<4>
<4>Pid : 1018, Comm: enigma2
<4>CPU : 0 Tainted: P (2.6.32.59_stm24_0211 #1)
<4>
<4>PC : 841c7eb4 SP : 8ba4def4 SR : 40008000 TEA : c1080888
<4>R0 : 00000001 R1 : 0000000c R2 : 00143000 R3 : 84012528
<4>R4 : 00000000 R5 : 00000000 R6 : ffffffff R7 : ffffffff
<4>R8 : 841c7eb0 R9 : c1080de8 R10 : 84118aa2 R11 : c0425afe
<4>R12 : fffffff7 R13 : 2b46f048 R14 : 00000000
<4>MACH: 0000052a MACL: b5c50000 GBR : 2b46f928 PR : c107e11e
<4>
<4>Call trace:
<4> [<c107f212>] 0xc107f212
<4> [<84069112>] 0x84069112
<4> [<84069a22>] 0x84069a22
<4> [<8406ffb4>] 0x8406ffb4
<4> [<8405d32e>] 0x8405d32e
<4> [<84069aaa>] 0x84069aaa
<4> [<84007920>] 0x84007920
<4> [<84069a7c>] 0x84069a7c
<4>
<4>Process: enigma2 (pid: 1018, stack limit = 8ba4c001)
<4>Stack: (0x8ba4def4 to 0x8ba4e000)
<4>dee0: c107f212 2b46eefe fffffff2
<4>df00: c0425afe 37fc2f62 84069112 c0425afe 2b46eefe 8b36c4a0 00000001 84069a22
<4>df20: 8b36c4a0 2b46eefe 8b36c4a0 000000a8 c17d2898 00000000 00000000 8406ffb4
<4>df40: 00000014 00008002 00000000 8b36c4a0 00000000 8b85bd60 8b5a7050 00000002
<4>df60: 8405d32e 00000000 00000000 84069aaa 2b46f048 fffffff7 c0425afe 2b46eefe
<4>df80: 00000014 8b36c4a0 00000001 84007920 0000059c 00000000 00000071 00000100
<4>dfa0: 84069a7c 00461244 00461244 2b46f534 00000036 00000014 c0425afe 2b46eefe
<4>dfc0: 2b46f53c 2b46ef4c 00000001 29f3f4b4 00000000 29f52038 2b46f048 00000000
<4>dfe0: 2b46eefc 2a23c524 00488018 00000000 2b46f928 00000003 00000090 0000004c
<4>---[ end trace 9190661e372836fc ]---

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

das ist aber nicht der Kernel den ich gerade hochgeladen hab ????
das dürfte das hier garnicht mehr erscheinen LED level = 1 ?!??

hat der denn das update neu gedownloadet und installiert ?

EDIT

Ach scheisse Git pull vergessen moment ...

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ja hat er gemacht.....ich bin vorher von 139 auf 143 gegangen.....
am display stand DL UP....Copy....usw bis dann FERTIG da stand
nochmal versuchen?

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ja jetzt bitte nochmal , ich hatte da was vergessen beim git bauen

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

:yahoo::yahoo::yahoo: yeah......Du bist der beste!!!! läuft wieder!!!:yahoo::yahoo::yahoo:

nur beim Display einstellen ist die Box jetzt abgeschmiert-.-
ich wollte die Kanalnummer weghaben^^

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

das geht aber habs nen paar mal getestet, versuchs einfach nochmal, war sicher nen prob wegen dem vorherigen display tool

Boahh das ging doch habs doch getestet, jetzt bekomm ich da auch nen screen , man was wie nen scheiss

 

[Speedy2310]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

ja es gab nen green screen mit ner fehlermeldung und dann ist die box von selbst neu gestartet......der fehler ist weg und das display war korrekt eingestellt!

Danke für Deine Super Arbeit!!!

 

[Ducktrick]

AW: Aktuelles Duck-Trick RAMFS Release **Support Thread**

Ja das war in dem plugin eine zeile die es eigentlich nicht mehr gab ... -.-, ich habs noch ergännst, wenn du in sachen dispaly anzeige noch was ändern willst dann amch das update nochmal dann sollte alles klappen jetzt


Allerdings geht eben durch den Display treiber Fehler den wir vorhin hatten das abschallten des Displays im Standby nicht ...