Erweiterte Modifzierung des Pogoplug E02 und Debian

[Alex]

AW: Erweiterte Modifzierung des Pogoplug E02 und Debian

Steht doch im Post eins, wie du den Kernel durch einen gemoddeten ersetzt.

 

[Zoran78]

AW: Erweiterte Modifzierung des Pogoplug E02 und Debian

Joo stimmt. Danke. War heute Nacht als ich den Beitrag geschrieben hatte echt schon spät :emoticon-0124-worri

 

[Deleted member 130877]

AW: Erweiterte Modifzierung des Pogoplug E02 und Debian

Guten morgen Leute,

jetzt startet meine Pogo nicht mehr nach der Anleitung.

Das war die letzte Eingabe:
Pogoplug:/tmp$ ubiformat /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: ubiformat: command not found

command not found!!! Super..Da war das neue mtd1 uImage-mtd1.img schon geschrieben.
Hier meine Komplette Eingabe:

Spoiler

login as: root
root@192.168.1.6's password:
Pogoplug:~$ mkfs.ext3 -L rootfs /dev/sda1
-bash: mkfs.ext3: command not found
Pogoplug:~$ cd /tmp
Pogoplug:/tmp$ mkdir usb
Pogoplug:/tmp$ mount /dev/sda1 /tmp/usb
Pogoplug:/tmp$ wget

Sie müssen registriert sein, um Links zu sehen.

Connecting to mehl.co (162.210.102.211:80)
nanddump 100% |*******************************| 21286 --:--:-- ETA
Pogoplug:/tmp$ chmod +x nanddump
Pogoplug:/tmp$ ./nanddump -nf usb/mtd0.oob /dev/mtd0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00100000...
Pogoplug:/tmp$ ./nanddump -nf usb/mtd1.oob /dev/mtd1
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00400000...
Pogoplug:/tmp$ ./nanddump -nf usb/mtd2.oob /dev/mtd2
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x02000000...
Pogoplug:/tmp$ ./nanddump -nof usb/mtd0 /dev/mtd0
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00100000...
Pogoplug:/tmp$ ./nanddump -nof usb/mtd1 /dev/mtd1
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x00400000...
Pogoplug:/tmp$ ./nanddump -nof usb/mtd2 /dev/mtd2
Block size 131072, page size 2048, OOB size 64
Dumping data starting at 0x00000000 and ending at 0x02000000...
Pogoplug:/tmp$ umount /dev/sda1
Pogoplug:/tmp$ wget

Sie müssen registriert sein, um Links zu sehen.

wget: not an http or ftp url:

Sie müssen registriert sein, um Links zu sehen.

.gz
Pogoplug:/tmp$ tar zxvf RescueV2.8.2-10292012.tar.gz
rootfs-mtd2.img
uImage-mtd1.img
Pogoplug:/tmp$ flash_eraseall /dev/mtd1
Erasing 128 Kibyte @ 3e0000 -- 96 % complete.
Pogoplug:/tmp$ nandwrite /dev/mtd1 uImage-mtd1.img
Writing data to block 0
Writing data to block 20000
Writing data to block 40000
Writing data to block 60000
Writing data to block 80000
Writing data to block a0000
Writing data to block c0000
Writing data to block e0000
Writing data to block 100000
Writing data to block 120000
Writing data to block 140000
Writing data to block 160000
Writing data to block 180000
Writing data to block 1a0000
Writing data to block 1c0000
Writing data to block 1e0000
Writing data to block 200000
Writing data to block 220000
Writing data to block 240000
Writing data to block 260000
Writing data to block 280000
Writing data to block 2a0000
Writing data to block 2c0000
Writing data to block 2e0000
Writing data to block 300000
Writing data to block 320000
Writing data to block 340000
Writing data to block 360000
Pogoplug:/tmp$
Pogoplug:/tmp$ flash_eraseall /dev/mtd2
Erasing 128 Kibyte @ 40000 -- 0 % complete.
Skipping bad block at 0x00060000
Erasing 128 Kibyte @ 1fe0000 -- 99 % complete.
Pogoplug:/tmp$ ubiformat /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: ubiformat: command not found
Pogoplug:/tmp$ cd
Pogoplug:~$ flash_eraseall /dev/mtd1
Erasing 128 Kibyte @ 3e0000 -- 96 % complete.
Pogoplug:~$ nandwrite /dev/mtd1 uImage-mtd1.img
open input file: No such file or directory
Pogoplug:~$
Pogoplug:~$ flash_eraseall /dev/mtd2
Erasing 128 Kibyte @ 40000 -- 0 % complete.
Skipping bad block at 0x00060000
Erasing 128 Kibyte @ 1fe0000 -- 99 % complete.
Pogoplug:~$ ubiformat /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: ubiformat: command not found
Pogoplug:~$ flash_eraseall /dev/mtd1
Erasing 128 Kibyte @ 3e0000 -- 96 % complete.
Pogoplug:~$ nandwrite /dev/mtd1 uImage-mtd1.img
open input file: No such file or directory
Pogoplug:~$ cd tmp
-bash: cd: tmp: No such file or directory
Pogoplug:~$ cd /tmp
Pogoplug:/tmp$ flash_eraseall /dev/mtd1
Erasing 128 Kibyte @ 3e0000 -- 96 % complete.
Pogoplug:/tmp$ nandwrite /dev/mtd1 uImage-mtd1.img
Writing data to block 0
Writing data to block 20000
Writing data to block 40000
Writing data to block 60000
Writing data to block 80000
Writing data to block a0000
Writing data to block c0000
Writing data to block e0000
Writing data to block 100000
Writing data to block 120000
Writing data to block 140000
Writing data to block 160000
Writing data to block 180000
Writing data to block 1a0000
Writing data to block 1c0000
Writing data to block 1e0000
Writing data to block 200000
Writing data to block 220000
Writing data to block 240000
Writing data to block 260000
Writing data to block 280000
Writing data to block 2a0000
Writing data to block 2c0000
Writing data to block 2e0000
Writing data to block 300000
Writing data to block 320000
Writing data to block 340000
Writing data to block 360000
Pogoplug:/tmp$ flash_eraseall /dev/mtd2
Erasing 128 Kibyte @ 40000 -- 0 % complete.
Skipping bad block at 0x00060000
Erasing 128 Kibyte @ 1fe0000 -- 99 % complete.
Pogoplug:/tmp$ ubiformat /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: ubiformat: command not found
Pogoplug:/tmp$ format /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: format: command not found
Pogoplug:/tmp$ /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: /dev/mtd2: Permission denied
Pogoplug:/tmp$ su /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: su: command not found
Pogoplug:/tmp$ /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: /dev/mtd2: Permission denied
Pogoplug:/tmp$ cd
Pogoplug:~$ /dev/mtd2 -s 512 -f rootfs-mtd2.img -y
-bash: /dev/mtd2: Permission denied
<e 'setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts'
-bash: fw_setenv: command not found
<n set_bootargs_rescue; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000'
-bash: fw_setenv: command not found
Pogoplug:~$ fw_setenv bootcmd_pogo 'run bootcmd_rescue'
-bash: fw_setenv: command not found
Pogoplug:~$ fw_setenv rescue_installed 1
-bash: fw_setenv: command not found
Pogoplug:~$ cd /tmp
Pogoplug:/tmp$ mkdir usb
mkdir: cannot create directory 'usb': File exists
Pogoplug:/tmp$ mount /dev/sda1 /tmp/usb
Pogoplug:/tmp$ wget

Sie müssen registriert sein, um Links zu sehen.

Connecting to mehl.co (162.210.102.211:80)
wget: can't open 'nanddump': File exists
Pogoplug:/tmp$ chmod +x nanddump
Pogoplug:/tmp$ ./nanddump -nf /dev/mtd0 usb/mtd0.oob
MEMGETINFO: Inappropriate ioctl for device
Pogoplug:/tmp$

Danach habe ich versucht den dump wieder einzuspielen. Hat aber nicht geklappt. Dann habe ich leicht sinnig den Stecker gezogen!
Über SSH komme ich nicht mehr rein und die LED vorne bleiben auch aus.
Was kann ich jetzt tun?Brauche eure Hilfe.

Edit: Hab mir sicherheitshalber schon mal ein USB zu TTL-Konverter bestellt, falls ich damit die Pogo wieder zum laufen bringe.

Sie müssen registriert sein, um Links zu sehen.

 

[Deleted member 130877]

AW: Erweiterte Modifzierung des Pogoplug E02 und Debian

So Leute,

mit dieser Anleitung klappt das nicht. Ist mein uboot defekt?

Sie müssen registriert sein, um Links zu sehen.

Hab diesen TTL Connector:

Sie müssen registriert sein, um Links zu sehen.

Was mache ich falsch?

edit:
scheint ein Wackelkontakt zu geben:

Spoiler

done.find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Block device usb 0 not supported


** Invalid boot device **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
** Block device usb 0 not supported
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
** Block device usb 0 not supported
** Block device usb 0 not supported
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: read_nand_cached: error reading nand off 0x560000 size 8192 bytes done.
find_inode failed for name=uboot-original-mtd0.kwb
load: Failed to find inode
### JFFS2 LOAD ERROR<0> for uboot-original-mtd0.kwb!
resetting ...




U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02


SoC: Kirkwood 88F6281_A0
DRAM: 256 MiB
WARNING: Caches not enabled
NAND: 128 MiB
In: serial
Out: serial
Err: serial
Net: egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for device 2

Was muss ich jetzt machen?
edit: u-boot>> printenv

Spoiler

u-boot>> printenv
arcNumber=3542
baudrate=115200
bootcmd=usb start; run force_rescue_bootcmd; run ubifs_bootcmd; run usb_bootcmd; usb stop; run rescue_bootcmd; run pogo_bootcmd; reset
bootdelay=3
console=ttyS0,115200
ethact=egiga0
ethaddr=00:25:31:04:9C:75
force_rescue=0
force_rescue_bootcmd=if test $force_rescue -eq 1 || ext2load usb 0:1 0x1700000 /rescueme 1 || fatload usb 0:1 0x1700000 /rescueme.txt 1; then run rescue_bootcmd; fi
led_error=orange blinking
led_exit=green off
led_init=green blinking
machid=dd6
mainlineLinux=yes
mtdids=nand0=orion_nand
mtdparts=mtdparts=orion_nand:1M(u-boot),4M(uImage),32M(rootfs),-(data)
partition=nand0,2
pogo_bootcmd=if fsload uboot-original-mtd0.kwb; then go 0x800200; fi
rescue_bootcmd=if test $rescue_installed -eq 1; then run rescue_set_bootargs; nand read.e 0x800000 0x100000 0x400000; bootm 0x800000; else run pogo_bootcmd; fi
rescue_installed=0
rescue_set_bootargs=setenv bootargs console=$console ubi.mtd=2 root=ubi0:rootfs ro rootfstype=ubifs $mtdparts $rescue_custom_params
stderr=serial
stdin=serial
stdout=serial
ubifs_bootcmd=run ubifs_set_bootargs; if ubi part data && ubifsmount rootfs && ubifsload 0x800000 /boot/uImage && ubifsload 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; fi
ubifs_mtd=3
ubifs_set_bootargs=setenv bootargs console=$console ubi.mtd=$ubifs_mtd root=ubi0:rootfs rootfstype=ubifs $mtdparts $ubifs_custom_params
usb_boot=mw 0x800000 0 1; ext2load usb $usb_device 0x800000 /boot/uImage; if ext2load usb $usb_device 0x1100000 /boot/uInitrd; then bootm 0x800000 0x1100000; else bootm 0x800000; fi
usb_bootcmd=run usb_init; run usb_set_bootargs; run usb_boot
usb_device=0:1
usb_init=run usb_scan
usb_root=/dev/sda1
usb_rootdelay=10
usb_rootfstype=ext3
usb_scan=usb_scan_done=0;for scan in $usb_scan_list; do run usb_scan_$scan; if test $usb_scan_done -eq 0 && ext2load usb $usb 0x800000 /boot/uImage 1; then usb_scan_done=1; echo "Found bootable drive on usb $usb"; setenv usb_device $usb; setenv usb_root /dev/$dev; fi; done
usb_scan_1=usb=0:1 dev=sda1
usb_scan_2=usb=1:1 dev=sdb1
usb_scan_3=usb=2:1 dev=sdc1
usb_scan_4=usb=3:1 dev=sdd1
usb_scan_list=1 2 3 4
usb_set_bootargs=setenv bootargs console=$console root=$usb_root rootdelay=$usb_rootdelay rootfstype=$usb_rootfstype $mtdparts $usb_custom_params


Environment size: 2355/131068 bytes

 

[tcash]

Hallo Community,



ich versuche ein Rescue System auf einen aktuellen (3.16.0-kirkwood-tld-2) Pogoplug zu bringen.



Leider schlägt der Flash Befehl immer fehl, weil er kein mtd2 Device findet

root@debian:~# flash_eraseall /dev/mtd2

flash_eraseall: /dev/mtd2: No such file or directory



Bei cat /proc/mtd bekomme ich nur nachfolgende Devices angezeigt.

dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 07f00000 00020000 "rootfs"

Bei einem Pogo vom Bekannten bekomme ich nach dem Aufruf von cat /proc/mtd nachfolgende Ausgabe.

dev: size erasesize name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00400000 00020000 "uImage"
mtd2: 02000000 00020000 "rootfs"
mtd3: 05b00000 00020000 "data"

Über etwas Hilfestellung wäre ich sehr erfreut.