=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.09.17 08:30:59 =~=~=~=~=~=~=~=~=~=~=~=
BCM97400
AB
FFFFFFFF
1s
Sync=1
LLMB=1
L2=1
RAC_I=1
RAC_D=1
Copy Code...34TUCV
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M8000
FIRST STAGE 1.10 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
Configure MEMC1_2........ Done
0.039 - fp init
FP version 7 detected
0.106 - ca init
0.804 - load config
1.384 - config loaded.
* press
to enter setup
1.398 - ide init
OLED found!
lcd: BOOT #84
- NAND PROBE: 2c da 80 95 (normal)
1.754 - main control
- read config file: /boot/secondstage.conf
1.760 - load /boot/secondstage.conf to 833000c0 (max=65535)
detected jffs2 blocksize: 128kb
++++++++++++++++++++++++++++++++++++++++++++++++++++++++
3.869 - jffs2 size: 7168 kb
3.871 - network: 3.873 manual, ip address is 192.168.2.15
3.929 - starting network
3.935 - httpd, telnetd, dreamupd
dreamupd initialized
3.940 - ok. start receiving packets
3.944 - using jffs2
Scanning JFFS2 FS: | / - \ | / - \ | / - \ | . / - \ | / - \ | / - \ | / - done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
4.093 - size: 0
- failed to open /boot/secondstage.conf
4.099 - not entering setup
4.101 - execute script: /cf/autorun.bat
4.105 - load /cf/autorun.bat to 833000c0 (max=65535)
4.109 - size: -1
- failed to open /cf/autorun.bat
4.114 - force boot: -1
4.116 - try boot from 1:
4.119 - execute script: /boot/autoexec.bat
4.123 - load /boot/autoexec.bat to 833000c0 (max=65535)
4.128 - using jffs2
4.130 - size: 152
lcd: /boot/bootlogo-dm8000.elf.gz
4.159 oled: string too long: '/boot/bootlogo-dm8000.elf.gz'
4.182 - load /boot/bootlogo-dm8000.elf.gz to 82000000 (max=16777216)
4.188 - using jffs2
4.203 - size: 263951
4.205 - decompressing elf (compressed: 263951 bytes)
4.268 - decompression ok (uncompressed: 655068 bytes)
4.273 - loading elf image at 88000000
4.469 - jumping to 8044ef80
4.472 - load /boot/bootlogo-dm8000.jpg to a2800000 (max=1048576)
4.477 - using jffs2
4.509 - size: 42664
bootlogo size: 42664
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-3.2-dm8000.gz
5.248 oled: string too long: '/boot/vmlinux-3.2-dm8000.gz'
5.271 - load /boot/vmlinux-3.2-dm8000.gz to 82000000 (max=16777216)
5.277 - using jffs2
5.355 - size: 2835644
5.357 - decompressing elf (compressed: 2835644 bytes)
5.974 - decompression ok (uncompressed: 6044028 bytes)
5.979 - loading elf image at 88000000
6.749 * Quiesce...
6.751 *** Turning off USB
6.753 *** Quiesce network...
6.767 - jumping to 804889b0
[ 0.000000] Linux version 3.2-dm8000 (weazle@toxbox.merlin3.info) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Thu Aug 1 17:14:31 CEST 2013
[ 0.000000] Fetching vars from bootloader...
[ 0.000000] Early serial console at MMIO32 0x10400b00 (options '115200n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
[ 0.000000] Using 256 MB RAM (from straps)
[ 0.000000] Fetch var 'memsize' = '154'
[ 0.000000] CPU revision is: 0002a042 (Brcm4380)
[ 0.000000] FPU revision is: 00130001
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] bmem: adding 148 MB LINUX region at 5 MB (0x0941e000@0x005e2000)
[ 0.000000] bmem: adding 102 MB RESERVED region at 154 MB (0x06600000@0x09a00000)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00010000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00010000
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 8058afc0, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768
[ 0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null debug bmem=102M@154M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.000000] Memory: 149348k/262144k available (4698k kernel code, 112796k reserved, 979k data, 220k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Measuring MIPS counter frequency...
[ 0.000000] Detected MIPS clock frequency: 405 MHz (202.507 MHz counter)
[ 0.000000] Console: colour dummy device 80x25
[ 0.001000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
[ 0.013000] pid_max: default: 32768 minimum: 301
[ 0.014000] Mount-cache hash table entries: 512
[ 0.017000] SMP: Booting CPU1...
[ 0.018000] CPU revision is: 0002a042 (Brcm4380)
[ 0.018000] FPU revision is: 00130001
[ 0.018000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.018000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.029000] SMP: CPU1 is running
[ 0.029000] Brought up 2 CPUs
[ 0.030000] devtmpfs: initialized
[ 0.034000] NET: Registered protocol family 16
[ 0.036000] PCI2.3->SDRAM window: 256 MB
[ 0.043000] bio: create slab <bio-0> at 0
[ 0.045000] SCSI subsystem initialized
[ 0.046000] libata version 3.00 loaded.
[ 0.047000] usbcore: registered new interface driver usbfs
[ 0.048000] usbcore: registered new interface driver hub
[ 0.049000] usbcore: registered new device driver usb
[ 0.050000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.051000] pci 0000:00:01.0: [168c:001a] type 0 class 0x000200
[ 0.052000] PCI: found device 168c:001a on PCI2.3 bus, slot 1 (irq 33)
[ 0.053000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.054000] pci 0000:00:01.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff]
[ 0.055000] pci 0000:00:01.0: BAR 0: set to [mem 0xd0000000-0xd000ffff] (PCI address [0xd0000000-0xd000ffff])
[ 0.056000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
[ 0.057000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
[ 0.058000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
[ 0.059000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
[ 0.060000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
[ 0.061000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
[ 0.062000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
[ 0.063000] Switching to clocksource upg
[ 0.075000] NET: Registered protocol family 2
[ 0.080000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.087000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.095000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.102000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.109000] TCP reno registered
[ 0.112000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.118000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.125000] NET: Registered protocol family 1
[ 0.130000] RPC: Registered named UNIX socket transport module.
[ 0.136000] RPC: Registered udp transport module.
[ 0.141000] RPC: Registered tcp transport module.
[ 0.146000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.153000] PCI: CLS 0 bytes, default 64
[ 0.160000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.168000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 0.178000] msgmni has been set to 291
[ 0.183000] io scheduler noop registered
[ 0.187000] io scheduler cfq registered (default)
[ 0.192000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.220000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
[ 0.229000] loop: module loaded
[ 0.233000] sata_brcmstb 0000:01:00.0: version 4.0
[ 0.238000] brcm-pm: enabling sata clocks
[ 0.242000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
[ 0.248000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 0.451000] scsi0 : sata_brcmstb
[ 0.455000] scsi1 : sata_brcmstb
[ 0.459000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
[ 0.466000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
[ 0.704000] 4366 kb/s
[ 0.706000] - NAND PROBE: 2c da 80 95
[ 0.710000] ONFI flash detected
[ 0.713000] ONFI param page 0 valid
[ 0.717000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD)
[ 0.725000] Scanning device for bad blocks
[ 0.800000] ata1: SATA link down (SStatus 4 SControl 300)
[ 0.901000] Creating 4 MTD partitions on "MT29F2G08AAD":
[ 0.907000] 0x000000000000-0x000010000000 : "complete"
[ 0.914000] 0x000000000000-0x000000100000 : "loader"
[ 0.920000] 0x000000100000-0x000000800000 : "boot"
[ 0.926000] 0x000000800000-0x000010000000 : "root"
[ 0.933000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
[ 0.942000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:1c:5a:19)
[ 0.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.957000] brcm-pm: enabling usb clocks
[ 0.961000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.966000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 1.005000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[ 1.016000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 1.022000] hub 1-0:1.0: USB hub found
[ 1.026000] hub 1-0:1.0: 2 ports detected
[ 1.031000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 1.036000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 1.075000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
[ 1.086000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 1.092000] hub 2-0:1.0: USB hub found
[ 1.096000] hub 2-0:1.0: 2 ports detected
[ 1.101000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.107000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 1.111000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.119000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
[ 1.126000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[ 1.132000] ata2.00: ATA-8: SAMSUNG HD105SI, 1AJ100E4, max UDMA/133
[ 1.139000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.165000] ata2.00: configured for UDMA/133
[ 1.170000] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD105SI 1AJ1 PQ: 0 ANSI: 5
[ 1.179000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.187000] sd 1:0:0:0: [sda] Write Protect is off
[ 1.192000] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.202000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.202000] hub 3-0:1.0: USB hub found
[ 1.202000] hub 3-0:1.0: 2 ports detected
[ 1.202000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 1.202000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
[ 1.202000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
[ 1.257000] hub 4-0:1.0: USB hub found
[ 1.259000] sda: sda1
[ 1.264000] hub 4-0:1.0: 2 ports detected
[ 1.268000] I
anschließend hab ich per Telnet init 4 um den gui zu beenden eingegeben und dann enigma2 dann kam folgendes:
opendreambox 2.0.0 dm8000
dm8000 login: root
.-------------------------------------------------------.
| _____ .__ .__ ________ |
| / \ ___________| | |__| ____ \_____ \ |
| / \ / \_/ __ \_ __ \ | | |/ \ _(__ < |
| / Y \ ___/| | \/ |_| | | \ / \ |
| \____|__ /\___ >__| |____/__|___| / /______ / |
| \/ \/ \/ \/ |
|
Sie müssen registriert sein, um Links zu sehen.
|
+-------------------------------------------------------+
type 'help' for a list of commands
root@dm8000:~# init4
-sh: init4: not found
root@dm8000:~# init 4
root@dm8000:~# enigma 2
-sh: enigma: not found
root@dm8000:~# enigma2
enigma2: error while loading shared libraries: /lib/librt.so.1: ELF file data en coding not little-endian
root@dm8000:~#