Dream friert immer ein

[Karl-Hein]

AW: Dream friert immer ein

Du solltest auch testen mit: Alle Medien von der Box entfernen, SD Card, HDD, USB Stick und USB Adapter für DVD Laufwerk (intern)
Dann neu flashen und testen !
-------------------------------
Es könnte auch dein Netzteil defekt sein !

 

[gittie]

AW: Dream friert immer ein

Nur warum läuft das mit OE 1.6 ?

 

[Karl-Hein]

AW: Dream friert immer ein

Was du noch machen könntest die Box neu flashen mit:
Link ist nicht mehr aktiv.

Seriell flashen !

Neu flashen mit DreamUP_1_3_3_11 + Bad Sector Repair (unter Extra- DreamUP_1_3_3_11 aktivieren) + Netzwerk (per LAN-Kabel mit dem Router verbinden) !

Wenn du alles richtig gemacht hast öffnet sich der "Flash-Button" in DreamUP_1_3_3_11 !

Jetzt sofort die Box IP ( steht in DreamUP_1_3_3_11 ) in den IE und flashen !

----------------------------------
Box manuell neu booten!
----------------------------

Link ist nicht mehr aktiv.

 

[gittie]

AW: Dream friert immer ein

So hab ich gemacht wie Du vorgeschlagen hast nun schauen wir mal was passiert.

Hab hier noch mal ein Log vom Merlin 2.0, lief gestern bis ich heute morgen da hab ich festgestellte das die Uhr wieder bei 01:43 Uhr stand hat sich also wieder festgefressen.
Anschießend mit Putty ein Bootlog erstellt.

Spoiler

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.09.17 08:30:59 =~=~=~=~=~=~=~=~=~=~=~=

BCM97400
AB
FFFFFFFF

1s
Sync=1
LLMB=1
L2=1
RAC_I=1
RAC_D=1

Copy Code...34TUCV

(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.

Dreambox D M8000
FIRST STAGE 1.10 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)

0.000 - BCM board setup
Configure MEMC1_2........ Done
0.039 - fp init
FP version 7 detected
0.106 - ca init
0.804 - load config
1.384 - config loaded.
* press to enter setup
1.398 - ide init
OLED found!
lcd: BOOT #84
- NAND PROBE: 2c da 80 95 (normal)
1.754 - main control
- read config file: /boot/secondstage.conf
1.760 - load /boot/secondstage.conf to 833000c0 (max=65535)
detected jffs2 blocksize: 128kb
++++++++++++++++++++++++++++++++++++++++++++++++++++++++
3.869 - jffs2 size: 7168 kb
3.871 - network: 3.873 manual, ip address is 192.168.2.15
3.929 - starting network
3.935 - httpd, telnetd, dreamupd
dreamupd initialized
3.940 - ok. start receiving packets
3.944 - using jffs2
Scanning JFFS2 FS: | / - \ | / - \ | / - \ | . / - \ | / - \ | / - \ | / - done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
4.093 - size: 0
- failed to open /boot/secondstage.conf
4.099 - not entering setup
4.101 - execute script: /cf/autorun.bat
4.105 - load /cf/autorun.bat to 833000c0 (max=65535)
4.109 - size: -1
- failed to open /cf/autorun.bat
4.114 - force boot: -1
4.116 - try boot from 1:
4.119 - execute script: /boot/autoexec.bat
4.123 - load /boot/autoexec.bat to 833000c0 (max=65535)
4.128 - using jffs2
4.130 - size: 152
lcd: /boot/bootlogo-dm8000.elf.gz
4.159 oled: string too long: '/boot/bootlogo-dm8000.elf.gz'
4.182 - load /boot/bootlogo-dm8000.elf.gz to 82000000 (max=16777216)
4.188 - using jffs2
4.203 - size: 263951
4.205 - decompressing elf (compressed: 263951 bytes)
4.268 - decompression ok (uncompressed: 655068 bytes)
4.273 - loading elf image at 88000000
4.469 - jumping to 8044ef80
4.472 - load /boot/bootlogo-dm8000.jpg to a2800000 (max=1048576)
4.477 - using jffs2
4.509 - size: 42664
bootlogo size: 42664
no HDMI device detected
no HDMI mode available, reverting to 720p
using 1280x720p (60.00 Hz)
HDMI
using colorspace: 0
create surface 1280 720
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /boot/vmlinux-3.2-dm8000.gz
5.248 oled: string too long: '/boot/vmlinux-3.2-dm8000.gz'
5.271 - load /boot/vmlinux-3.2-dm8000.gz to 82000000 (max=16777216)
5.277 - using jffs2
5.355 - size: 2835644
5.357 - decompressing elf (compressed: 2835644 bytes)
5.974 - decompression ok (uncompressed: 6044028 bytes)
5.979 - loading elf image at 88000000
6.749 * Quiesce...
6.751 *** Turning off USB
6.753 *** Quiesce network...
6.767 - jumping to 804889b0
[ 0.000000] Linux version 3.2-dm8000 (weazle@toxbox.merlin3.info) (gcc version 4.6.4 20120303 (prerelease) (GCC) ) #1 SMP Thu Aug 1 17:14:31 CEST 2013
[ 0.000000] Fetching vars from bootloader...
[ 0.000000] Early serial console at MMIO32 0x10400b00 (options '115200n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Options: sata=1 enet=1 emac_1=0 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
[ 0.000000] Using 256 MB RAM (from straps)
[ 0.000000] Fetch var 'memsize' = '154'
[ 0.000000] CPU revision is: 0002a042 (Brcm4380)
[ 0.000000] FPU revision is: 00130001
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 10000000 @ 00000000 (usable)
[ 0.000000] bmem: adding 148 MB LINUX region at 5 MB (0x0941e000@0x005e2000)
[ 0.000000] bmem: adding 102 MB RESERVED region at 154 MB (0x06600000@0x09a00000)
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00010000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00010000
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] free_area_init_node: node 0, pgdat 8058afc0, node_mem_map 81000000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65024 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @81203000 s5440 r8192 d15040 u32768
[ 0.000000] pcpu-alloc: s5440 r8192 d15040 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
[ 0.000000] Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=null debug bmem=102M@154M
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.000000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.000000] Memory: 149348k/262144k available (4698k kernel code, 112796k reserved, 979k data, 220k init, 0k highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Measuring MIPS counter frequency...
[ 0.000000] Detected MIPS clock frequency: 405 MHz (202.507 MHz counter)
[ 0.000000] Console: colour dummy device 80x25
[ 0.001000] Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
[ 0.013000] pid_max: default: 32768 minimum: 301
[ 0.014000] Mount-cache hash table entries: 512
[ 0.017000] SMP: Booting CPU1...
[ 0.018000] CPU revision is: 0002a042 (Brcm4380)
[ 0.018000] FPU revision is: 00130001
[ 0.018000] Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
[ 0.018000] Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
[ 0.029000] SMP: CPU1 is running
[ 0.029000] Brought up 2 CPUs
[ 0.030000] devtmpfs: initialized
[ 0.034000] NET: Registered protocol family 16
[ 0.036000] PCI2.3->SDRAM window: 256 MB
[ 0.043000] bio: create slab <bio-0> at 0
[ 0.045000] SCSI subsystem initialized
[ 0.046000] libata version 3.00 loaded.
[ 0.047000] usbcore: registered new interface driver usbfs
[ 0.048000] usbcore: registered new interface driver hub
[ 0.049000] usbcore: registered new device driver usb
[ 0.050000] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.051000] pci 0000:00:01.0: [168c:001a] type 0 class 0x000200
[ 0.052000] PCI: found device 168c:001a on PCI2.3 bus, slot 1 (irq 33)
[ 0.053000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x0000ffff]
[ 0.054000] pci 0000:00:01.0: BAR 0: assigned [mem 0xd0000000-0xd000ffff]
[ 0.055000] pci 0000:00:01.0: BAR 0: set to [mem 0xd0000000-0xd000ffff] (PCI address [0xd0000000-0xd000ffff])
[ 0.056000] pci 0000:01:00.0: [14e4:8602] type 0 class 0x000101
[ 0.057000] PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
[ 0.058000] pci 0000:01:00.0: reg 24: [mem 0x00000000-0x00000fff]
[ 0.059000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x000007ff pref]
[ 0.060000] pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
[ 0.061000] pci 0000:01:00.0: BAR 5: set to [mem 0x10510000-0x10510fff] (PCI address [0x10510000-0x10510fff])
[ 0.062000] pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
[ 0.063000] Switching to clocksource upg
[ 0.075000] NET: Registered protocol family 2
[ 0.080000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.087000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.095000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.102000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.109000] TCP reno registered
[ 0.112000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[ 0.118000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[ 0.125000] NET: Registered protocol family 1
[ 0.130000] RPC: Registered named UNIX socket transport module.
[ 0.136000] RPC: Registered udp transport module.
[ 0.141000] RPC: Registered tcp transport module.
[ 0.146000] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.153000] PCI: CLS 0 bytes, default 64
[ 0.160000] JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 0.168000] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 0.178000] msgmni has been set to 291
[ 0.183000] io scheduler noop registered
[ 0.187000] io scheduler cfq registered (default)
[ 0.192000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.220000] serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
[ 0.229000] loop: module loaded
[ 0.233000] sata_brcmstb 0000:01:00.0: version 4.0
[ 0.238000] brcm-pm: enabling sata clocks
[ 0.242000] PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
[ 0.248000] PCI: Setting latency timer of device 0000:01:00.0 to 64
[ 0.451000] scsi0 : sata_brcmstb
[ 0.455000] scsi1 : sata_brcmstb
[ 0.459000] ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
[ 0.466000] ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
[ 0.704000] 4366 kb/s
[ 0.706000] - NAND PROBE: 2c da 80 95
[ 0.710000] ONFI flash detected
[ 0.713000] ONFI param page 0 valid
[ 0.717000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD)
[ 0.725000] Scanning device for bad blocks
[ 0.800000] ata1: SATA link down (SStatus 4 SControl 300)
[ 0.901000] Creating 4 MTD partitions on "MT29F2G08AAD":
[ 0.907000] 0x000000000000-0x000010000000 : "complete"
[ 0.914000] 0x000000000000-0x000000100000 : "loader"
[ 0.920000] 0x000000100000-0x000000800000 : "boot"
[ 0.926000] 0x000000800000-0x000010000000 : "root"
[ 0.933000] bcmemac: Broadcom STB 10/100 EMAC driver v3.0
[ 0.942000] bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:09:34:1c:5a:19)
[ 0.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.957000] brcm-pm: enabling usb clocks
[ 0.961000] ehci-brcm ehci-brcm.0: Broadcom STB EHCI
[ 0.966000] ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
[ 1.005000] ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
[ 1.016000] ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
[ 1.022000] hub 1-0:1.0: USB hub found
[ 1.026000] hub 1-0:1.0: 2 ports detected
[ 1.031000] ehci-brcm ehci-brcm.1: Broadcom STB EHCI
[ 1.036000] ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
[ 1.075000] ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
[ 1.086000] ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
[ 1.092000] hub 2-0:1.0: USB hub found
[ 1.096000] hub 2-0:1.0: 2 ports detected
[ 1.101000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.107000] ohci-brcm ohci-brcm.0: Broadcom STB OHCI
[ 1.111000] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.119000] ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
[ 1.126000] ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
[ 1.132000] ata2.00: ATA-8: SAMSUNG HD105SI, 1AJ100E4, max UDMA/133
[ 1.139000] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 1.165000] ata2.00: configured for UDMA/133
[ 1.170000] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD105SI 1AJ1 PQ: 0 ANSI: 5
[ 1.179000] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 1.187000] sd 1:0:0:0: [sda] Write Protect is off
[ 1.192000] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.202000] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.202000] hub 3-0:1.0: USB hub found
[ 1.202000] hub 3-0:1.0: 2 ports detected
[ 1.202000] ohci-brcm ohci-brcm.1: Broadcom STB OHCI
[ 1.202000] ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
[ 1.202000] ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
[ 1.257000] hub 4-0:1.0: USB hub found
[ 1.259000] sda: sda1
[ 1.264000] hub 4-0:1.0: 2 ports detected
[ 1.268000] I

anschließend hab ich per Telnet init 4 um den gui zu beenden eingegeben und dann enigma2 dann kam folgendes:
opendreambox 2.0.0 dm8000


dm8000 login: root
.-------------------------------------------------------.
| _____ .__ .__ ________ |
| / \ ___________| | |__| ____ \_____ \ |
| / \ / \_/ __ \_ __ \ | | |/ \ _(__ < |
| / Y \ ___/| | \/ |_| | | \ / \ |
| \____|__ /\___ >__| |____/__|___| / /______ / |
| \/ \/ \/ \/ |
|

Sie müssen registriert sein, um Links zu sehen.

|
+-------------------------------------------------------+
type 'help' for a list of commands
root@dm8000:~# init4
-sh: init4: not found
root@dm8000:~# init 4
root@dm8000:~# enigma 2
-sh: enigma: not found
root@dm8000:~# enigma2
enigma2: error while loading shared libraries: /lib/librt.so.1: ELF file data en coding not little-endian
root@dm8000:~#

Bis dahin fuhr sie hoch dann blieb der Balken bei ungefähr der Hälfte stehen und dann ging nichts mehr.