DM500HD "card initializing error" nach OSCAM update

[elminator]

Hallo zusammen,

ich habe ein OSCAM update gemacht und jetzt kann meine Karte nicht mehr initialisieren.

oscam.conf:

Spoiler

[global]
nice = -1
waitforcards = 1
logfile = /etc/tuxbox/config/oscam.log
maxlogsize = 1024


[newcamd]
key = XXXX
port = 54321@09c4:000000


[webif]
httpport = 54320
httpuser = user
httppwd = pass
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255


[monitor]
port = 54323

oscam.server

Spoiler

[reader]
label = v13
protocol = internal
device = /dev/sci0
caid = 09C4
boxid = 596C3056
detect = cd
mhz = 357
cardmhz = 357
ident = 09C4:000000
group = 1
emmcache = 1,3,2
enable = 1

Jetzt hänge ich noch mal die verschiedenen logs an:

Spoiler

OSCAM-1.00.5471
2014/05/01 21:36:09 77FE3000 s services reloaded: 0 services freed, 1 services loaded
2014/05/01 21:36:09 77FE3000 s userdb reloaded: 8 accounts loaded, 0 expired, 0 disabled
2014/05/01 21:36:09 77FE3000 s signal handling initialized (type=sysv)
2014/05/01 21:36:09 77FE3000 s 1432 service-id's loaded in 23ms
2014/05/01 21:36:09 77FE3000 s 37 tier-id's loaded
2014/05/01 21:36:09 77FE3000 s 912 provid's loaded
2014/05/01 21:36:09 77FE3000 s monitor: initialized (fd=7, port=54323)
2014/05/01 21:36:09 77FE3000 s camd33: disabled
2014/05/01 21:36:09 77FE3000 s camd35: disabled
2014/05/01 21:36:09 77FE3000 s cs378x: disabled
2014/05/01 21:36:09 77FE3000 s newcamd: initialized (fd=8, port=54321, crypted)
2014/05/01 21:36:09 77FE3000 s CAID: 09C4
2014/05/01 21:36:09 77FE3000 s provid #0: 000000
2014/05/01 21:36:09 77FE3000 s radegast: disabled
2014/05/01 21:36:09 77FE3000 s http thread started
2014/05/01 21:36:09 77FE3000 s creating thread for device /dev/sci0
2014/05/01 21:36:09 7641F4B0 r reader thread started (thread=7641F4B0, label=v13, device=/dev/sci0, detect=cd, mhz=500, cardmhz=500)
2014/05/01 21:36:09 77FE3000 s loadbalancer: can't read from file /tmp/.oscam/stat
2014/05/01 21:36:09 77FE3000 s waiting for local card init
2014/05/01 21:36:09 76C1F4B0 h HTTP Server listening on port 54320
2014/05/01 21:36:10 7641F4B0 r v13 card detected
2014/05/01 21:36:11 7641F4B0 r ATR: 3F FF 11 25 03 10 80 41 B0 07 69 FF 4A 50 70 00 00 50 31 01 00 11
2014/05/01 21:36:12 7641F4B0 r Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] parental lock setting: FF FF FF FF
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] type: VideoGuard Sky Germany, caid: 09C4
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] serial: 000FE909, BoxID: 12345678, baseyear: 1997
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] ready for requests
2014/05/01 21:36:14 7641F4B0 r found cardsystem videoguard2
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] v13 card detected
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] type: VideoGuard Sky Germany
2014/05/01 21:36:14 7641F4B0 r [videoguard2-reader] tier: 1389, expiry date: 2002/02/01-00:01:16
2014/05/01 21:36:15 77FE3000 s init for all local cards done

OSCAM-1.20.9693
Status Live Log Config Readers Users Services Files Failban CacheEX Scripts Restart
2014/05/01 21:51:38 0 s >> OSCam << cardserver started, version 1.20-unstable_svn, build r9693 (mipsel-unknown-linux-gnu)
2014/05/01 21:51:38 0 s creating pidfile /tmp/.oscam/oscam.pid with pid 5023
2014/05/01 21:51:38 0 s services reloaded: 0 services freed, 1 services loaded, rejected 0
2014/05/01 21:51:38 0 s userdb reloaded: 8 accounts loaded, 0 expired, 0 disabled
2014/05/01 21:51:38 0 s signal handling initialized
2014/05/01 21:51:38 0 s 1432 service-id's loaded in 25ms
2014/05/01 21:51:38 0 s 37 tier-id's loaded
2014/05/01 21:51:38 0 s 912 provid's loaded
2014/05/01 21:51:38 0 s monitor: initialized (fd=5, port=54323)
2014/05/01 21:51:38 0 s newcamd: initialized (fd=6, port=54321)
2014/05/01 21:51:38 0 s -> CAID: 09C4 PROVID: 000000
2014/05/01 21:51:38 0 s v13 [internal] creating thread for device /dev/sci0
2014/05/01 21:51:38 0 s loadbalancer: can't read from file /tmp/.oscam/stat
2014/05/01 21:51:38 0 s waiting for local card init
2014/05/01 21:51:38 77100CB8 r v13 [internal] Reader initialized (device=/dev/sci0, detect=cd, mhz=500, cardmhz=500)
2014/05/01 21:51:38 77100CB8 r v13 [internal] card detected
2014/05/01 21:51:38 ADC4E0 h webif: decompressed 152212 bytes back into 371000 bytes
2014/05/01 21:51:38 ADC4E0 h HTTP Server running. ip=0.0.0.0 port=54320
2014/05/01 21:51:39 77100CB8 r v13 [internal] ATR: 3F FF 11 25 03 10 80 41 B0 07 69 FF 4A 50 70 00 00 50 31 01 00 11
2014/05/01 21:51:39 77100CB8 r v13 [internal] Init card protocol T0, FI=1, F=372, D=1, N=3
2014/05/01 21:51:39 77100CB8 r v13 [internal] Calculated work ETU is 74.40 us reader mhz = 500
2014/05/01 21:51:39 77100CB8 r v13 [internal] ATR Fsmax is 5 MHz, clocking card to 5.00 (specified in reader->mhz)
2014/05/01 21:51:42 77100CB8 r v13 [internal] card system not supported
2014/05/01 21:51:42 77100CB8 r v13 [internal] Normal mode failed, reverting to Deprecated Mode
2014/05/01 21:51:43 77100CB8 r v13 [internal] ATR: 3F FF 11 25 03 10 80 41 B0 07 69 FF 4A 50 70 00 00 50 31 01 00 11
2014/05/01 21:51:43 77100CB8 r v13 [internal] Init card protocol T0, FI=1, F=372, D=1, N=3
2014/05/01 21:51:43 77100CB8 r v13 [internal] Calculated work ETU is 74.40 us reader mhz = 500
2014/05/01 21:51:43 77100CB8 r v13 [internal] ATR Fsmax is 5 MHz, clocking card to 5.00 (specified in reader->mhz)
2014/05/01 21:51:45 77100CB8 r v13 [internal] card system not supported
2014/05/01 21:51:45 77100CB8 r v13 [internal] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2014/05/01 21:51:45 77100CB8 r v13 [internal] card initializing error
2014/05/01 21:51:46 0 s init for all local cards done
2014/05/01 21:51:46 0 s anti cascading disabled

Vielleicht hat jemand noch eine idee?



DANKE

 

[Bodo-1]

AW: DM500HD "card initializing error" nach OSCAM update

Versuchmal in der oscam server so bitte :

cardmhz = 2700
mhz = 357 #(369/450/500) musst mal testen. Gegebenenfalls kannst du auch den Parameter komplett aus kommentieren bzw weglassen, dann musst du aber

autospeed = 1 setzen .

Dann reboot ....... und testen

gruss Bodo

Edit ; falls sie dann erkannt wird solltest du noch den fastmode einschalten !

in den oscam.server dann zusätzlich noch

ins7e11=15 kannst auch mit 13 oder 14 erstmal testen , weiss nicht wieviel mit der DM500 geht
ndsversion=2

 

[elminator]

AW: DM500HD "card initializing error" nach OSCAM update

Hi Bodo,

funktioniert!

Danke für die schnelle Antwort. GENIAL!

Gruß
Elminator