./push_firmware 5690Pro_07.90.all-rev114928_inhaus_freetz-ng-24274M-1321b9453_ssl_3_0_x_masterbox.image -prg ftp -afu
* Analyzing '5690Pro_07.90.all-rev114928_inhaus_freetz-ng-24274M-1321b9453_ssl_3_0_x_masterbox.image' ...
* Product: Fritz_Box_HW279 (FRITZ!Box 5690 Pro)
* Using dos2unix binary: /usr/bin/dos2unix
* Using tar binary: /usr/bin/tar
* Using ftp binary: /usr/bin/tnftp
* Target host: 192.168.178.1
* Outgoing IP: 192.168.178.13
* Flash mode: fit-boot
* Allowed memory size: 1024 MB
* Designated linux_fs_start: <other>
!!! WARNING !!! WARNING !!! WARNING !!! WARNING !!! WARNING !!!
!!! THERE IS NO WARRANTY AT ALL !!! USE AT YOUR OWN RISK !!!
* Are you sure, that you want to flash this file to the device?
5690Pro_07.90.all-rev114928_inhaus_freetz-ng-24274M-1321b9453_ssl_3_0_x_masterbox.image
Proceed? (y/[n]) y
* You should now reboot your box (192.168.178.1). Waiting for shut down.
Switch off, if reboot is not detected because it happens too quickly.
Some newer bootloader versions allow to flash on power-cycle only.
* No reply from box, assuming switch-off or restart. Trying to re-detect box.
Waiting ..... found!
* Reading 'env' file to /tmp/freetz_env_XvA
Connected to 192.168.178.1.
220 ADAM2 FTP Server ready
331 Password required for adam2
230 User adam2 successfully logged in
Remote system type is AVM.
Debugging on (debug=1).
---> TYPE I
200 Type set to BINARY
---> SYST
215 AVM EVA Version 1.12588 0x0 0x4C6409
---> MEDIA SDRAM
200 Media set to MEDIA_SDRAM
local: /tmp/freetz_env_XvA remote: env
---> SIZE env
502 Command not implemented
ftp: setsockopt SO_DEBUG (ignored): Keine Berechtigung
---> EPSV
502 Command not implemented
disabling epsv4 for this connection
---> PASV
227 Entering Passive Mode (192,168,178,1,39,10)
---> RETR env
150 Opening BINARY data connection
Timeout!!!!!!!!!!!!!!!!!!
ProductID: Fritz_Box_HW279
HWRevision: 279
HWSubRevision: 3
memsize: 0x80000000
linux_fs_start: 1
* MAPSTART=0x40000000
* FULLSIZE=0x40000000 (1024 MB)
* MAPLIMIT=0x80000000
* FILESIZE=0x03772e3b (~55 MB)
* ALIBYTES=0x0000d1c5 (~52 kB)
* FREESIZE=0x3c880000 (~968 MB)
* MTDSTART=0x7c880000
* Box is back up again, initiating transfer.
Connected to 192.168.178.1.
220 ADAM2 FTP Server ready
331 Password required for adam2
230 User adam2 successfully logged in
Remote system type is AVM.
Debugging on (debug=1).
---> TYPE I
200 Type set to BINARY
---> MEDIA SDRAM
200 Media set to MEDIA_SDRAM
---> SETENV memsize 0x3c880000
200 SETENV command successful
---> SETENV kernel_args_tmp "mtdram1=0x7c880000,0x80000000 mtdparts_ext=update-image.0:0x3772e3b@0x0(fit-image)"
200 SETENV command successful
local: /tmp/freetz_cV9/fitboot.flash remote: 0x7c880000 0x80000000
ftp: setsockopt SO_DEBUG (ignored): Keine Berechtigung
---> EPSV
502 Command not implemented
disabling epsv4 for this connection
---> PASV
227 Entering Passive Mode (192,168,178,1,20,28)
---> STOR 0x7c880000 0x80000000
150 Opening BINARY data connection
100% |***********************************| 56779 KiB 22.75 MiB/s 00:00 ETA
226 Transfer complete
58142267 bytes sent in 00:28 (1.92 MiB/s)
---> QUIT
221 Thank you for using the FTP service on ADAM2
done
