Serials beginning with XAJ1
XAJ1003100 (and above) -
Patched
Serials beginning with XAW4
XAW400110 (and lower) -
Not Patched
XAW400120 - Possibly patched
XAW400300 (and above) -
Patched
Serials beginning with XAW1:
XAW100780 (and lower) -
Not Patched
XAW100790 - Possibly patched
XAW1009XX (and above) -
Patched
Serials beginning with XAW7:
XAW70017XXXXXX (and lower) -
Not Patched
XAW70018XXXXXX - Possibly patched
XAW70019XXXXXX (and above) -
Patched
Serials beginning with XAJ4:
XAJ40050XXXXXX (and lower) -
Not Patched
XAJ40051XXXXXX - Possibly patched
XAJ4006XXXXXXX (and above) -
Patched
Serials beginning with XAJ7:
XAJ70043300XXX (and lower) -
Not Patched
XAJ700434XXXXX - Possibly patched
XAJ7005XXXXXXX (and above) -
Patched
so kannst du es testen
Anleitung englisch
So what if your serial is "Possibly Patched" or "Patched"?
Here is what you can do before you purchase the TX SX Pro or a license for SX OS to see if it will work for your Nintendo Switch.
This is how to test
FOR SURE if your switch has been patched.
You will need the following:
Download
Sie müssen registriert sein, um Links zu sehen.
GUI and
Sie müssen registriert sein, um Links zu sehen.
You will also need a USB-C to USB-A cable and a method of entering RCM mode.
There are many different DIY solutions for entering Rcm mode, so find the option that works best for you.
Steps:
1. Enter Rcm Mode on your switch
Insert jig (or use any DIY method of shorting pin 10 in the right joycon rail)
Hold Vol+
Press Power button
Your switch should have booted a black screen. If you see the Nintendo logo, you need to power the switch completely off and try again. If you pressed power and your screen still appears to be off... do not worry, you may have entered Rcm successfully.
2. On your PC, you will need to launch TegraRcm GUI and install the APX driver.
Launch TegraRcm GUI
Go to Settings tab
click "Install Driver"
Du musst angemeldet sein, um Bilder zu sehen.
If you see the APX driver not found dialogue, click "Yes"
Du musst angemeldet sein, um Bilder zu sehen.
3. Plug your switch into your PC with the USB C to USB A cable.
You should see the "RCM O.K." message
Du musst angemeldet sein, um Bilder zu sehen.
4. CLOSE the TegraRcm GUI
5. Now you must copy biskeydump.bin into your TegraRCMGUI directory.
Du musst angemeldet sein, um Bilder zu sehen.
6. Open the command prompt and navigate to your TegraRcm GUI directory
Here is an example
Du musst angemeldet sein, um Bilder zu sehen.
7. Now you must run the following command:
TegraRcmSmash.exe -w biskeydump.bin BOOT:0x0
Now check the resulting output. There are two possible outcomes.
1. The switch will accept and execute the payload displaying 0x7000 and a QR code will display on your switch. This indicates your Switch is
NOT PATCHED! If this is your result, then
the TX SX Pro dongle and SX OS will work on your switch!
Du musst angemeldet sein, um Bilder zu sehen.
2. The switch will accept the payload, but does not execute displaying 0x0000. This indicates your switch IS PATCHED and is currently not expoitable. The current version of the TX SX Pro dongle and SX OS will NOT work on your switch. If this is your situation, please keep checking the TX front page and user forums for news as Team Xecuter is currently investigating a solution. No ETA is available at this time...
Du musst angemeldet sein, um Bilder zu sehen.
Credit: screen shots used in this guide are from
Sie müssen registriert sein, um Links zu sehen.
(thank you
Sie müssen registriert sein, um Links zu sehen.
)
