Hi,
nachdem ich nach dieser Anleitung vorgegangen bin, Bootschleife.
Serial komme ich auf die Box, nach Abruch mit "CRTL C" des Bootvorganges auch mit FTP und Telnet. Sicherung des Image und "nanddump-mtd1.bin" habe ich.
Wie soll ich weiter vorgehen? Die "nanddump-mtd1.bin" zurückspielen, aber wie?
Hier der Serialdump:
nachdem ich nach dieser Anleitung vorgegangen bin, Bootschleife.
ür diejenigen die gerne ihren Vip1 Vip2 oder Vip1v2 dazu bewegen wollen den kernel aus dem nand booten zu lassen, für die hab ich da mal was vorbereitet
Achtung !!! kein ILTV Boot mehr möglich ohne neu Flashen danach, Achtung !!!
Vorgehensweise :
Um euch das ändern der Bootargs zu ersparen hab ich das anhand eines nand Backups für euch vorbereitet. Bei diesem Backup wird der uboot mit den nötigen änderungen und der kernel in den nand kopiert, beim boot wird dann aus dem nand gebootet, wie ihr ein Kernel Updaten händisch machen könnt schreib ich unten dran !
das zip downloaden und entpacken, die nand-backup.bin peer ftp auf die box nach /media kopieren.
anschliessend in Telnet folgendes
Code:
flash_eraseall /dev/mtd3
dd if=/media/nand-backup.bin of=/dev/mtd3
mv /media/sda1/boot/uImage /media/sda1/boot/_uImage
Das wars, nach nen roboot wird der kernel aus dem nand gebootet
Achtung !!! kein ILTV Boot mehr möglich ohne neu Flashen danach, Achtung !!!
Vorgehensweise :
Um euch das ändern der Bootargs zu ersparen hab ich das anhand eines nand Backups für euch vorbereitet. Bei diesem Backup wird der uboot mit den nötigen änderungen und der kernel in den nand kopiert, beim boot wird dann aus dem nand gebootet, wie ihr ein Kernel Updaten händisch machen könnt schreib ich unten dran !
das zip downloaden und entpacken, die nand-backup.bin peer ftp auf die box nach /media kopieren.
anschliessend in Telnet folgendes
Code:
flash_eraseall /dev/mtd3
dd if=/media/nand-backup.bin of=/dev/mtd3
mv /media/sda1/boot/uImage /media/sda1/boot/_uImage
Das wars, nach nen roboot wird der kernel aus dem nand gebootet
Serial komme ich auf die Box, nach Abruch mit "CRTL C" des Bootvorganges auch mit FTP und Telnet. Sicherung des Image und "nanddump-mtd1.bin" habe ich.
Wie soll ich weiter vorgehen? Die "nanddump-mtd1.bin" zurückspielen, aber wie?
Hier der Serialdump:
[SPOILER ]Board: STb7100-Reference (MB442) [29-bit mode]
U-Boot 1.3.1 (Mar 12 2010 - 15:04:58) - stm23_0043
DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
IdentID : 03 00 08 00 00 44 e6
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
** Unable to read "/boot/uImage" from usb 0:1 **
## Booting image at 00040000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 3652442 Bytes = 3.5 MiB
Load Address: 84001000
Entry Point: 84002000
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw ip=172.100.100.60:172.100.100.10:172.100.100.1:255.255.255.0:SpiderBox:eth0
Linux version 2.6.32.59_stm24_0211 (server@server) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun Dec 13 16:54:42 CET 2015
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: STb7100 Reference board
Node 0: start_pfn = 0x4000, low = 0xc000
Zone PFN ranges:
Normal 0x00004000 -> 0x0000c000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00004000 -> 0x0000c000
Edision Argus Reference board initialisation
STx7109 version 3.x
Chip version 3.4
Setting version to 4.0 to match commercial branding
bpa2: partition 'LMI_VID' created at 0x10800000, size 90112 kB (0x05800000 B)
bpa2: partition 'LMI_SYS' created at 0x0463b000, size 18432 kB (0x01200000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
PVR=04061100 CVR=30480000 PRR=00009300
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 106012k/131072k available (2707k kernel code, 817k data, 1616k init)
Hierarchical RCU implementation.
NR_IRQS:600
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 264.19 BogoMIPS (lpj=528384)
Mount-cache hash table entries: 512
CPU: STx7109
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Generic PHY: Registered new driver (0xffffffff)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 207
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
loop: module loaded
MiPHY driver style MiPHY-DUMMY probed successfully
MiPHY-DUMMY, c0.0 Claimed by sata-stm
scsi0 : sata-stm
ata1: SATA max UDMA/133 irq 170
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash at offset 0x7f0000
No RedBoot partition table detected in physmap-flash
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash":
0x000000000000-0x000000040000 : "Boot (RO)"
0x000000040000-0x0000006a0000 : "jffs2 (RW)"
0x000000700000-0x000000800000 : "NAND-END (RO)"
0x000000000000-0x000000800000 : "Kompletter Nand Flash (RW) - Loeschen ohne neue Firmware - JTAG noetig"
slram: not enough parameters.
STe100p: Registered new driver (0x1c040011)
STe101p: Registered new driver (0x00061c50)
DWMAC100
No HW DMA feature register supported
Normal descriptors
smsc911x: Driver version 2008-10-21.
nwhw_config: (eth0) setting mac address: 00:80:e1:12:06:30
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_48_clk clock not found for stm-usb.0
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
ata1: SATA link down (SStatus 0 SControl 0)
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
i2c /dev entries driver
i2c_st40_pio: ST40 PIO based I2C Driver for STM24
Linux video capture interface: v2.00
usbcore: registered new interface driver ushc
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0000000 size 0x00400000
cop. addr 0x10000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0400000 size 0x00400000
cop. addr 0x10400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac handler (16 channels).
IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7109 cut 4.0 SOC audio subsystem
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 1616k freed
usb 1-1: new high speed USB device using stm-ehci and address 2
---------------- RAMFS Load ---------------------
-------------------------------------------------
Installing Busybox
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: wait 0 seconds on usb port 1
scsi 1:0:0:0: Direct-Access JetFlash Transcend 8GB 8.07 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 15687680 512-byte logical blocks: (8.03 GB/7.48 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda:INIT VFD
Fulan front panel driver
YWPANEL_VFD_DETECT: Frontcontroller I2C: 02:28 @2675
YWPANEL_VFD_DETECT: result=1, vfd_type=2
VfdType = 2
YWPANEL_VFD_Init: YWPANEL_VFD_Initialize(): 0 @2852
CpuType = -2077624828
DisplayInfo = 0
scankeyNum = 176
swMajorVersion = 8
swSubVersion = 193
sda1 sda2 sda3 sda4
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
input: fulan front panel buttons as /devices/virtual/input/input0
aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
aotom_vip1: exports duplicate symbol I2C_bus_add (owned by aotom)
insmod: can't insert '/drvko/aotom_vip1.ko': invalid module format
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA1 OK
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA2 OK
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA4 OK
Mount rootfs /dev/sda1
umount /dev/sda1
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
mount /dev/sda2
EXT2-fs: sda2: couldn't mount because of unsupported optional features (240).
EXT4-fs (sda2): mounted filesystem with ordered data mode
umount: /etc/mtab: No such file or directory
Switch and Load new RootFS
INIT: version 2.86 booting
Nand mount Check
Nand Speicher mounten für E2...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000: 0x0527 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000004: 0x83ea instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000008: 0x6d56 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000000c: 0x3700 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x0084 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000014: 0x0084 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000018: 0x6280 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000001c: 0x0905 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000020: 0x694c instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000024: 0x2d78 instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010000: 0x9ec8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010004: 0xab44 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010008: 0x7d63 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001000c: 0x63cf instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010010: 0x7d16 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010014: 0xf2ef instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010018: 0x39ee instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001001c: 0xffd3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010020: 0x8f77 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010024: 0xaf63 instead
Further such events for this erase block will not be printed
Old JFFS2 bitmask found at 0x0001bb60
You cannot use older JFFS2 filesystems with newer kernels
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020000: 0xfbe7 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020004: 0x3f80 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020008: 0xa477 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002000c: 0x458d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020010: 0x2060 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020014: 0x84b2 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020018: 0xd2bb instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002001c: 0x1231 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020020: 0xa32b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020024: 0xb0de instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030000: 0x9633 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030004: 0xdbc8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030008: 0x9dda instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0003000c: 0x5416 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030010: 0x1bd9 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030014: 0x7843 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030018: 0x85cf instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0003001c: 0x0f1f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030020: 0xe76d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030024: 0x87e2 instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040000: 0xc0e3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040004: 0x5e8e instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040008: 0x0f76 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004000c: 0xbad8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040010: 0xb2b5 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040014: 0x9201 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040018: 0xbf5b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004001c: 0xbeb5 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040020: 0x6874 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040024: 0x390a instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050000: 0x6ef9 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050004: 0x535d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050008: 0x3df0 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0005000c: 0x456f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050010: 0xecea instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050014: 0xe87a instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050018: 0xbf6b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0005001c: 0xe7af instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050020: 0x148b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050024: 0x3c94 instead
Further such events for this erase block will not be printed
bitmask 0x1985 not found at 0x00080014: 0x5bc6 instead
2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b000c: 0x3ee3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0010: 0x8d7b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0014: 0xe27b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0018: 0x5cee instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b001c: 0xd8fb instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0020: 0x1bde instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0024: 0xe3a3 instead
Further such events for this erase block will not be printed
Old JFFS2 bitmask found at 0x00257058
You cannot use older JFFS2 filesystems with newer kernels
Old JFFS2 bitmask found at 0x0025e748
usw...........
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370000: 0x7ab7 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370004: 0x7181 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370008: 0x259f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0037000c: 0xeb68 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370010: 0xfdfc instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370014: 0xecb0 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370018: 0xd3e1 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0037001c: 0x0f5b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370020: 0xc057 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370024: 0x6ee7 instead
Further such events for this erase block will not be printed
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 46, bad_blocks 0, c->nr_blocks 102
mount: mounting /dev/mtdblock1 on /media/nand failed: Input/output error
Lade Filesystem Treiber fat vfat ...
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
modprobe: can't load module nls_koi8-ru.ko (/lib/modules/2.6.32.59_stm24_0211/nls_koi8-ru.ko): Invalid argument
Fertig
Mount /dev in tmpfs
Copying device nodes to /dev
Segmentation fault
Starting portmap daemon....
Starting DEBUG Interface
Mounting local filesystems...
EXT2-fs: sda4: couldn't mount because of unsupported optional features (240).
mount: mounting /dev/sdb1 on /media/sdb1 failed: No such device or address
Cleaning /tmpSegmentation fault
Segmentation fault
Segmentation fault
.
Start bootlog!!!
Bootlog woks 120 sec then end
Overclock OFF -- Default
cat: can't open '/var/keys/Benutzerdaten/.system/mac': No such file or directory
init stmfb
Hostname: device probe found 2 display pipelines
ArgusVIP.
starting telnetd
cat: can't open '/etc/enigma2/settings': No such file or directory
HDMI Ausgang Aktviert
Segmentation fault
LOADING MODULES
load a firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
seeking to 0
seeking to 5f00
seeking to 12320
seeking to 1aa20
seeking to 173100
seeking to 173138
seeking to 173170
seeking to 1b9058
seeking to 1b9060
seeking to 1b9068
seeking to 1b9070
seeking to 1d0920
seeking to 1d0a00
load v firmware
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
seeking to 0
seeking to 1277c0
seeking to 1277f8
seeking to 127830
seeking to 14d558
seeking to 14d564
seeking to 14d570
seeking to 17df30
seeking to 180000
Segmentation fault
Segmentation fault
Segmentation fault
init embx
[DETECT] -> Boxdetect for Argus Boxes
[DETECT] -> Boxtype = Vip1v2
[DETECT] -> Tuner = sharp7306
init drivers
Load CI Modul Treiber
cimax loaded
init AVS
AVS Aktiviert -- VIP1v2
[AVS]: A/V switch handling for vip1_avs
[AVS]: init success
init player 191
init frontends
np-PTI Laden...
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 2048, waitMS = 20, camRouting = 0, enableStatistic = 0)
NP- Fertig
Load real TC Code
TC_Data = b9238000, TC_Code = b923c000
Readback TC ... successfull
using videoMem = 385024 (packets = 2048)
pti: pti_buffer_pool_init: allocate 94 pages (385024 bytes)
DMA(0) base = 526b000, top = 52c9000, buffer = 526b000, size 385024
freeBuffer(): free = 1
pti: pti_buffer_pool_init: allocate 94 pages (385024 bytes)
DMA(1) base = 5400000, top = 545e000, buffer = 5400000, size 385024
freeBuffer(): free = 2
pti_task: using 2 dma channel
DVB: registering adapter 0 frontend 0 (Sharp7306 Plug&Play (VIP1v2) )...
Free session: 0
Using session 0
Free session: 1
Using session 1
Free session: 2
Using session 2
player2
player fertig
Device /dev/net/tun nicht erstellt und tun.ko Modul nicht geladen... OpenVPN deaktiviert
Lade Swap /dev
FB Switch Startet first...
Lade Lirc STM-Default Treiber ...
LinuxDVB Test (press 'h' for help)
player_open: Using 0 (and 1)
player_open: Playing /boot/Enigma2.mp4 - Audio Video
StartMp4
StartMp4: 'mdhd' Track 0, TimeScale = 30000, Duration = 473473 (15)
StartMp4: Track 0 type = 'vide'
StartMp4: 'mdhd' Track 1, TimeScale = 44100, Duration = 693217 (15)
StartMp4: Track 1 type = 'soun'
BuildTrackMap: MOV track type 'vide': 472 chunks, 473 samples
BuildTrackMap: TimeScale 30000, Delta 1001
BuildTrackMap: MOV track type 'soun': 471 chunks, 677 samples
BuildTrackMap: TimeScale 44100, Delta 1024
*** Composition Data not present.
BuildTrackMap: TimeScale 44100, Delta 993
*** Composition Data not present.
ObeyCommand: Playback started
PlayH264Mp4File: avcC contents:
profile: 77
profile compatibility: 64
level: 41
nal length bytes: 4
number of sequence param sets: 1
sps 0 has length 22
number of picture param sets: 1
pps 0 has length 4
Starting FTP server: [AVS]: avs_command_kernel (10)
vsftpd.
Deconfiguring network interfaces... ifdown: interface eth0 not configured
done.
Starting dhcp
Starting DHCP client: udhcpcudhcpc (v1.21.0) started
eth0: device MAC address 00:80:e1:12:06:30
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
StopMp4:
Player: Terminating 1
CheckKey: Attempting to shut down
End of file (1): Running time = 17 seconds
Linux DVB Test terminating
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
failed...
No lease, failing
already running.
Overclock OFF -- Default
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... LOADING E2
starting e2->
rcS.user loaded
Autonews Aktiv ...
Samba Menu einstellungen nicht Aktiv...OFF
OpenVPN Autostart einstellungen nicht Aktiv...OFF
UPNP Autostart einstellungen nicht Aktiv...OFF
wget: bad address 'online.spdns.org'
Kartenslots Aktivieren ...
Boxtype: Vip1vcc = 5 -> Set ClassASetting clock to: 3.57Mhz
vcc = 5 -> Set ClassASetting clock to: 3.57Mhz
Registering device 'sc', major '169'
Version of smartcard driver: [1.0.1]
udhcpc (v1.21.0) started
Sending discover...
PYTHONPATH: /usr/lib/enigma2/python
chmod: /tmp/news.cfg: No such file or directory
/var/config/tools/autonews.sh: source: line 64: can't open '/tmp/news.cfg'
Sending discover...
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
STMFB accel interface available
+ (9) GFBDC
12288k total video mem
4188k usable video mem
2568kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) gLCDDC
eDBoxLCD::eDBoxLCD >
Error: No matching USB device found!
config -> (w 320, h 240)
lcd buffer 0x2aa4a008 153600 bytes, stride 640
eDBoxLCD::eDBoxLCD (w 320, h 240, depth 16)<
LCD resolution: 320 x 240 x 16 (stride: 640)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
couldnt open /dev/rfmod0!!!!
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "fulan front panel buttons" is a remotecontrol
Input device "TDT RC event driver" is a remotecontrol
failed to open /dev/input/event2
Input device "" is a remotecontrol
failed to open /dev/input/event3
Input device "" is a remotecontrol
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
CI Slot 0: reset requested
CI Slot 1: reset requested
CI Slot 0 setSource(0)
CI Slot 1 setSource(0)
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
cannot open /proc/stb/tsmux/input2
cannot open /proc/stb/tsmux/input3
done, found 2 common interface slots
+ (35) CA handler
+ (36) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
can't open /etc/enigma2/lamedb: No such file or directory
scanning for frontends..
opening frontend 0
close frontend 0
found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 13
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait5.png
found 4 spinner!
executing main
setIoPrio best-effort level 3 ok
resolveFilename: Couldn't create /etc/enigma2/
no profile data available
resolveFilename: Couldn't create /etc/enigma2/
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 5, in <module>
from Tools.Profile import profile, profile_final
File "/usr/lib/enigma2/python/Tools/Profile.py", line 27, in <module>
profile_file = open(resolveFilename(SCOPE_CONFIG, "profile"), "w")
TypeError: coercing to Unicode: need string or buffer, NoneType found
---- saving lame channel db
FATAL: couldn't save lame channel db!
Sending discover...
main thread is non-idle! display spinner!
FONT 'Regular' MISSING!
FONT 'Regular' MISSING!
main thread is non-idle! display spinner!
failed...
No lease, failing
done.
Emu Autostart ...
Emu Autostart ... FERTIG
RAM Leeren ...
RAM Leeren ... FERTIG
cat: can't open '/var/emu/setemu': No such file or directory
cat: can't open '/var/emu/setemu2': No such file or directory
kein Emu gesetzt
kein 2 Emu
Emu Watchdog Inaktiv
ENIGMA2 Running...
wget: bad address 'online.spdns.org'
Öffne Sources.list
/var/config/system/updatecheck.sh: source: line 45: can't open '/tmp/sources.list'
Killed
e2 ended <- RTV: 137
*
cat: can't open '/ram/switch': No such file or directory
ERROR
DONE
starting e2->
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
Sending all processes the TERM signal...done.
Sending all processes the KILL signal...done.
Deactivating swap...done.
Unmounting local filesystems...umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: ramfs buumount: sending ioctl 4c01 to a partition!
sy - remounted rumount: sending ioctl 4c01 to a partition!
ead-only
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
done.
INIT: Sending processes the TERM signal
Rebooting... Restarting system.
Board: STb7100-Reference (MB442) [29-bit mode]
U-Boot 1.3.1 (Mar 12 2010 - 15:04:58) - stm23_0043
DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
IdentID : 03 00 08 00 00 44 e6
Hit any key to stop autoboot: 0
(Re)start USB...
U-Boot 1.3.1 (Mar 12 2010 - 15:04:58) - stm23_0043
DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
IdentID : 03 00 08 00 00 44 e6
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
** Unable to read "/boot/uImage" from usb 0:1 **
## Booting image at 00040000 ...
Image Name: Linux-2.6.32.59_stm24_0211
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 3652442 Bytes = 3.5 MiB
Load Address: 84001000
Entry Point: 84002000
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/sda1 rw ip=172.100.100.60:172.100.100.10:172.100.100.1:255.255.255.0:SpiderBox:eth0
Linux version 2.6.32.59_stm24_0211 (server@server) (gcc version 4.6.3 20120613 (STMicroelectronics/Linux Base 4.6.3-111) (GCC) ) #1 PREEMPT Sun Dec 13 16:54:42 CET 2015
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: STb7100 Reference board
Node 0: start_pfn = 0x4000, low = 0xc000
Zone PFN ranges:
Normal 0x00004000 -> 0x0000c000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00004000 -> 0x0000c000
Edision Argus Reference board initialisation
STx7109 version 3.x
Chip version 3.4
Setting version to 4.0 to match commercial branding
bpa2: partition 'LMI_VID' created at 0x10800000, size 90112 kB (0x05800000 B)
bpa2: partition 'LMI_SYS' created at 0x0463b000, size 18432 kB (0x01200000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyAS0,115200 root=/dev/sda1 rw mem=128m bigpysarea=4000 coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:00:80:E1:12:06:30 init=/bin/devinit printk
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
PVR=04061100 CVR=30480000 PRR=00009300
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 106012k/131072k available (2707k kernel code, 817k data, 1616k init)
Hierarchical RCU implementation.
NR_IRQS:600
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 264.19 BogoMIPS (lpj=528384)
Mount-cache hash table entries: 512
CPU: STx7109
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
Generic PHY: Registered new driver (0xffffffff)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
NET: Registered protocol family 8
NET: Registered protocol family 20
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 207
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0x18032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0x18033000 (irq = 120) is a stm-asc
loop: module loaded
MiPHY driver style MiPHY-DUMMY probed successfully
MiPHY-DUMMY, c0.0 Claimed by sata-stm
scsi0 : sata-stm
ata1: SATA max UDMA/133 irq 170
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Searching for RedBoot partition table in physmap-flash at offset 0x7f0000
No RedBoot partition table detected in physmap-flash
Using physmap partition information
Creating 4 MTD partitions on "physmap-flash":
0x000000000000-0x000000040000 : "Boot (RO)"
0x000000040000-0x0000006a0000 : "jffs2 (RW)"
0x000000700000-0x000000800000 : "NAND-END (RO)"
0x000000000000-0x000000800000 : "Kompletter Nand Flash (RW) - Loeschen ohne neue Firmware - JTAG noetig"
slram: not enough parameters.
STe100p: Registered new driver (0x1c040011)
STe101p: Registered new driver (0x00061c50)
DWMAC100
No HW DMA feature register supported
Normal descriptors
smsc911x: Driver version 2008-10-21.
nwhw_config: (eth0) setting mac address: 00:80:e1:12:06:30
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_48_clk clock not found for stm-usb.0
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
ata1: SATA link down (SStatus 0 SControl 0)
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0x191ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0x191ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
i2c /dev entries driver
i2c_st40_pio: ST40 PIO based I2C Driver for STM24
Linux video capture interface: v2.00
usbcore: registered new interface driver ushc
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0000000 size 0x00400000
cop. addr 0x10000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xb0400000 size 0x00400000
cop. addr 0x10400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac handler (16 channels).
IRQ 140/fdma_dmac: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma: firmware: using built-in firmware fdma_STx7109_0.elf
platform fdma_dmac: SLIM hw 0.0, FDMA fw 4.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7109 cut 4.0 SOC audio subsystem
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 1616k freed
usb 1-1: new high speed USB device using stm-ehci and address 2
---------------- RAMFS Load ---------------------
-------------------------------------------------
Installing Busybox
usb 1-1: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: wait 0 seconds on usb port 1
scsi 1:0:0:0: Direct-Access JetFlash Transcend 8GB 8.07 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 15687680 512-byte logical blocks: (8.03 GB/7.48 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda:INIT VFD
Fulan front panel driver
YWPANEL_VFD_DETECT: Frontcontroller I2C: 02:28 @2675
YWPANEL_VFD_DETECT: result=1, vfd_type=2
VfdType = 2
YWPANEL_VFD_Init: YWPANEL_VFD_Initialize(): 0 @2852
CpuType = -2077624828
DisplayInfo = 0
scankeyNum = 176
swMajorVersion = 8
swSubVersion = 193
sda1 sda2 sda3 sda4
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI removable disk
input: fulan front panel buttons as /devices/virtual/input/input0
aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
aotom_vip1: exports duplicate symbol I2C_bus_add (owned by aotom)
insmod: can't insert '/drvko/aotom_vip1.ko': invalid module format
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA1 OK
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA2 OK
tune2fs: sending ioctl 127c to a partition!
tune2fs: sending ioctl 127c to a partition!
SDA4 OK
Mount rootfs /dev/sda1
umount /dev/sda1
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
mount /dev/sda2
EXT2-fs: sda2: couldn't mount because of unsupported optional features (240).
EXT4-fs (sda2): mounted filesystem with ordered data mode
umount: /etc/mtab: No such file or directory
Switch and Load new RootFS
INIT: version 2.86 booting
Nand mount Check
Nand Speicher mounten für E2...
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000000: 0x0527 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000004: 0x83ea instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000008: 0x6d56 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000000c: 0x3700 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000010: 0x0084 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000014: 0x0084 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000018: 0x6280 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0000001c: 0x0905 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000020: 0x694c instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00000024: 0x2d78 instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010000: 0x9ec8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010004: 0xab44 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010008: 0x7d63 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001000c: 0x63cf instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010010: 0x7d16 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010014: 0xf2ef instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010018: 0x39ee instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0001001c: 0xffd3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010020: 0x8f77 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00010024: 0xaf63 instead
Further such events for this erase block will not be printed
Old JFFS2 bitmask found at 0x0001bb60
You cannot use older JFFS2 filesystems with newer kernels
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020000: 0xfbe7 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020004: 0x3f80 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020008: 0xa477 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002000c: 0x458d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020010: 0x2060 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020014: 0x84b2 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020018: 0xd2bb instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0002001c: 0x1231 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020020: 0xa32b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00020024: 0xb0de instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030000: 0x9633 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030004: 0xdbc8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030008: 0x9dda instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0003000c: 0x5416 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030010: 0x1bd9 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030014: 0x7843 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030018: 0x85cf instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0003001c: 0x0f1f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030020: 0xe76d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00030024: 0x87e2 instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040000: 0xc0e3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040004: 0x5e8e instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040008: 0x0f76 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004000c: 0xbad8 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040010: 0xb2b5 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040014: 0x9201 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040018: 0xbf5b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0004001c: 0xbeb5 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040020: 0x6874 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00040024: 0x390a instead
Further such events for this erase block will not be printed
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050000: 0x6ef9 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050004: 0x535d instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050008: 0x3df0 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0005000c: 0x456f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050010: 0xecea instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050014: 0xe87a instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050018: 0xbf6b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0005001c: 0xe7af instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050020: 0x148b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00050024: 0x3c94 instead
Further such events for this erase block will not be printed
bitmask 0x1985 not found at 0x00080014: 0x5bc6 instead
2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b000c: 0x3ee3 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0010: 0x8d7b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0014: 0xe27b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0018: 0x5cee instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b001c: 0xd8fb instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0020: 0x1bde instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x000b0024: 0xe3a3 instead
Further such events for this erase block will not be printed
Old JFFS2 bitmask found at 0x00257058
You cannot use older JFFS2 filesystems with newer kernels
Old JFFS2 bitmask found at 0x0025e748
usw...........
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370000: 0x7ab7 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370004: 0x7181 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370008: 0x259f instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0037000c: 0xeb68 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370010: 0xfdfc instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370014: 0xecb0 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370018: 0xd3e1 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x0037001c: 0x0f5b instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370020: 0xc057 instead
jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x00370024: 0x6ee7 instead
Further such events for this erase block will not be printed
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 46, bad_blocks 0, c->nr_blocks 102
mount: mounting /dev/mtdblock1 on /media/nand failed: Input/output error
Lade Filesystem Treiber fat vfat ...
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
Segmentation fault
modprobe: can't load module nls_koi8-ru.ko (/lib/modules/2.6.32.59_stm24_0211/nls_koi8-ru.ko): Invalid argument
Fertig
Mount /dev in tmpfs
Copying device nodes to /dev
Segmentation fault
Starting portmap daemon....
Starting DEBUG Interface
Mounting local filesystems...
EXT2-fs: sda4: couldn't mount because of unsupported optional features (240).
mount: mounting /dev/sdb1 on /media/sdb1 failed: No such device or address
Cleaning /tmpSegmentation fault
Segmentation fault
Segmentation fault
.
Start bootlog!!!
Bootlog woks 120 sec then end
Overclock OFF -- Default
cat: can't open '/var/keys/Benutzerdaten/.system/mac': No such file or directory
init stmfb
Hostname: device probe found 2 display pipelines
ArgusVIP.
starting telnetd
cat: can't open '/etc/enigma2/settings': No such file or directory
HDMI Ausgang Aktviert
Segmentation fault
LOADING MODULES
load a firmware
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
seeking to 0
seeking to 5f00
seeking to 12320
seeking to 1aa20
seeking to 173100
seeking to 173138
seeking to 173170
seeking to 1b9058
seeking to 1b9060
seeking to 1b9068
seeking to 1b9070
seeking to 1d0920
seeking to 1d0a00
load v firmware
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
seeking to 0
seeking to 1277c0
seeking to 1277f8
seeking to 127830
seeking to 14d558
seeking to 14d564
seeking to 14d570
seeking to 17df30
seeking to 180000
Segmentation fault
Segmentation fault
Segmentation fault
init embx
[DETECT] -> Boxdetect for Argus Boxes
[DETECT] -> Boxtype = Vip1v2
[DETECT] -> Tuner = sharp7306
init drivers
Load CI Modul Treiber
cimax loaded
init AVS
AVS Aktiviert -- VIP1v2
[AVS]: A/V switch handling for vip1_avs
[AVS]: init success
init player 191
init frontends
np-PTI Laden...
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 2048, waitMS = 20, camRouting = 0, enableStatistic = 0)
NP- Fertig
Load real TC Code
TC_Data = b9238000, TC_Code = b923c000
Readback TC ... successfull
using videoMem = 385024 (packets = 2048)
pti: pti_buffer_pool_init: allocate 94 pages (385024 bytes)
DMA(0) base = 526b000, top = 52c9000, buffer = 526b000, size 385024
freeBuffer(): free = 1
pti: pti_buffer_pool_init: allocate 94 pages (385024 bytes)
DMA(1) base = 5400000, top = 545e000, buffer = 5400000, size 385024
freeBuffer(): free = 2
pti_task: using 2 dma channel
DVB: registering adapter 0 frontend 0 (Sharp7306 Plug&Play (VIP1v2) )...
Free session: 0
Using session 0
Free session: 1
Using session 1
Free session: 2
Using session 2
player2
player fertig
Device /dev/net/tun nicht erstellt und tun.ko Modul nicht geladen... OpenVPN deaktiviert
Lade Swap /dev
FB Switch Startet first...
Lade Lirc STM-Default Treiber ...
LinuxDVB Test (press 'h' for help)
player_open: Using 0 (and 1)
player_open: Playing /boot/Enigma2.mp4 - Audio Video
StartMp4
StartMp4: 'mdhd' Track 0, TimeScale = 30000, Duration = 473473 (15)
StartMp4: Track 0 type = 'vide'
StartMp4: 'mdhd' Track 1, TimeScale = 44100, Duration = 693217 (15)
StartMp4: Track 1 type = 'soun'
BuildTrackMap: MOV track type 'vide': 472 chunks, 473 samples
BuildTrackMap: TimeScale 30000, Delta 1001
BuildTrackMap: MOV track type 'soun': 471 chunks, 677 samples
BuildTrackMap: TimeScale 44100, Delta 1024
*** Composition Data not present.
BuildTrackMap: TimeScale 44100, Delta 993
*** Composition Data not present.
ObeyCommand: Playback started
PlayH264Mp4File: avcC contents:
profile: 77
profile compatibility: 64
level: 41
nal length bytes: 4
number of sequence param sets: 1
sps 0 has length 22
number of picture param sets: 1
pps 0 has length 4
Starting FTP server: [AVS]: avs_command_kernel (10)
vsftpd.
Deconfiguring network interfaces... ifdown: interface eth0 not configured
done.
Starting dhcp
Starting DHCP client: udhcpcudhcpc (v1.21.0) started
eth0: device MAC address 00:80:e1:12:06:30
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
StopMp4:
Player: Terminating 1
CheckKey: Attempting to shut down
End of file (1): Running time = 17 seconds
Linux DVB Test terminating
Sending discover...
Sending discover...
Sending discover...
Sending discover...
Sending discover...
failed...
No lease, failing
already running.
Overclock OFF -- Default
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... LOADING E2
starting e2->
rcS.user loaded
Autonews Aktiv ...
Samba Menu einstellungen nicht Aktiv...OFF
OpenVPN Autostart einstellungen nicht Aktiv...OFF
UPNP Autostart einstellungen nicht Aktiv...OFF
wget: bad address 'online.spdns.org'
Kartenslots Aktivieren ...
Boxtype: Vip1vcc = 5 -> Set ClassASetting clock to: 3.57Mhz
vcc = 5 -> Set ClassASetting clock to: 3.57Mhz
Registering device 'sc', major '169'
Version of smartcard driver: [1.0.1]
udhcpc (v1.21.0) started
Sending discover...
PYTHONPATH: /usr/lib/enigma2/python
chmod: /tmp/news.cfg: No such file or directory
/var/config/tools/autonews.sh: source: line 64: can't open '/tmp/news.cfg'
Sending discover...
+ (1) Background File Eraser
+ (5) Tuxtxt
+ (8) graphics acceleration manager
STMFB accel interface available
+ (9) GFBDC
12288k total video mem
4188k usable video mem
2568kB available for acceleration surfaces.
resolution: 720 x 576 x 32 (stride: 2880)
+ (9) gLCDDC
eDBoxLCD::eDBoxLCD >
Error: No matching USB device found!
config -> (w 320, h 240)
lcd buffer 0x2aa4a008 153600 bytes, stride 640
eDBoxLCD::eDBoxLCD (w 320, h 240, depth 16)<
LCD resolution: 320 x 240 x 16 (stride: 640)
+ (9) Font Render Class
[FONT] initializing lib...
[FONT] loading fonts...
[FONT] Intializing font cache, using max. 4MB...
+ (10) gRC
RC thread created successfully
+ (15) eWindowStyleManager
+ (20) DVB-CI UI
+ (20) UHF Modulator
couldnt open /dev/rfmod0!!!!
+ (20) RC Input layer
+ (20) misc options
+ (20) AVSwitch Driver
couldnt open /dev/dbox/fp0 to monitor vcr scart slow blanking changed!
+ (21) input device driver
Input device "fulan front panel buttons" is a remotecontrol
Input device "TDT RC event driver" is a remotecontrol
failed to open /dev/input/event2
Input device "" is a remotecontrol
failed to open /dev/input/event3
Input device "" is a remotecontrol
Found 4 input devices.
+ (22) Hdmi CEC driver
+ (30) eActionMap
+ (35) CI Slots
scanning for common interfaces..
CI Slot 0: reset requested
CI Slot 1: reset requested
CI Slot 0 setSource(0)
CI Slot 1 setSource(0)
eDVBCIInterfaces->setInputSource(0, 0)
eDVBCIInterfaces->setInputSource(1, 1)
cannot open /proc/stb/tsmux/input2
cannot open /proc/stb/tsmux/input3
done, found 2 common interface slots
+ (35) CA handler
+ (36) Stream server
[SERVERSOCKET] ERROR on bind() (Address already in use)
+ (40) eServiceCenter
settings instance.
+ (41) eServiceFactoryDVD
+ (41) eServiceFactoryM2TS
+ (41) eServiceFactoryMP3
+ (41) eServiceFactoryFS
+ (41) eServiceFactoryDVB
reached rl 70
---- opening lame channel db
can't open /etc/enigma2/lamedb: No such file or directory
scanning for frontends..
opening frontend 0
close frontend 0
found 1 adapter, 1 frontends(1 sim) and 3 demux, boxtype 13
RTC not ready... wait for transponder time
[EPGC] Initialized EPGCache (wait for setCacheFile call now)
Loading spinners...
[ePNG] couldn't open /usr/local/share/enigma2/skin_default/spinner/wait5.png
found 4 spinner!
executing main
setIoPrio best-effort level 3 ok
resolveFilename: Couldn't create /etc/enigma2/
no profile data available
resolveFilename: Couldn't create /etc/enigma2/
Traceback (most recent call last):
File "/usr/lib/enigma2/python/mytest.py", line 5, in <module>
from Tools.Profile import profile, profile_final
File "/usr/lib/enigma2/python/Tools/Profile.py", line 27, in <module>
profile_file = open(resolveFilename(SCOPE_CONFIG, "profile"), "w")
TypeError: coercing to Unicode: need string or buffer, NoneType found
---- saving lame channel db
FATAL: couldn't save lame channel db!
Sending discover...
main thread is non-idle! display spinner!
FONT 'Regular' MISSING!
FONT 'Regular' MISSING!
main thread is non-idle! display spinner!
failed...
No lease, failing
done.
Emu Autostart ...
Emu Autostart ... FERTIG
RAM Leeren ...
RAM Leeren ... FERTIG
cat: can't open '/var/emu/setemu': No such file or directory
cat: can't open '/var/emu/setemu2': No such file or directory
kein Emu gesetzt
kein 2 Emu
Emu Watchdog Inaktiv
ENIGMA2 Running...
wget: bad address 'online.spdns.org'
Öffne Sources.list
/var/config/system/updatecheck.sh: source: line 45: can't open '/tmp/sources.list'
Killed
e2 ended <- RTV: 137
*
cat: can't open '/ram/switch': No such file or directory
ERROR
DONE
starting e2->
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
Sending all processes the TERM signal...done.
Sending all processes the KILL signal...done.
Deactivating swap...done.
Unmounting local filesystems...umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
umount: ramfs buumount: sending ioctl 4c01 to a partition!
sy - remounted rumount: sending ioctl 4c01 to a partition!
ead-only
umount: sending ioctl 4c01 to a partition!
umount: sending ioctl 4c01 to a partition!
done.
INIT: Sending processes the TERM signal
Rebooting... Restarting system.
Board: STb7100-Reference (MB442) [29-bit mode]
U-Boot 1.3.1 (Mar 12 2010 - 15:04:58) - stm23_0043
DRAM: 128 MiB
NOR: 8 MiB
In: serial
Out: serial
Err: serial
IdentID : 03 00 08 00 00 44 e6
Hit any key to stop autoboot: 0
(Re)start USB...
Zuletzt bearbeitet: