IPC - problem nach reboot …

[feissmaik]

AW: IPC - problem nach reboot …

Aha wieso hast du denn nen SATA Kartenlesegerät für die CF verbaut?
Es gibt auch CF auf IDE Adapter, weil viel mehr kriegen die CF karten eh nicht hin (ATA133) ... das wäre wohl die bessere wahl gewesen aber Oke, du scheinst kein Problem damit zu haben mehr Geld dafür ausgeben zu müssen...

Und im BIOS "Load Defaults" hattest auch mal gemacht gehabt?



Naja wie gesagt eine genau Meldung vom fehler beim booten wäre interessant....

 

[Cubelles]

Re: AW: IPC - problem nach reboot …

da das board kein ide-anschluss hat nur sata

load defaults hab ich im bios gemacht leider ohne erfolg

wenn du mir sagst in welcher logdate die genaue fehlermeldung gelockt wird, kann ich die hier reinsetzen.


gruß

 

[TommyH99]

AW: IPC - problem nach reboot …

ich kenn nur bootlogd

nano /etc/default/bootlogd

und dann auf YES setzen!

 

[feissmaik]

AW: IPC - problem nach reboot …

...ich wiederhole mich echt mega ungerne...

in welcher logdatei genau das drin steht kann ich dir nicht sagen (bzw ich ich schon?) und ich kenn nichtmals die fehlermeldung aber ein 4.mal werde ich danach nicht fragen!

wo du aber zum beispiel reingucken kannst habe ich dir hier ebenfals schon mind. 2x erklärt....


@TommyH99: Guter Tip.... dann wird der Bootvorgang unter /var/log/boot gespeichert...

 

[Cubelles]

unter /var/log/boot steht das drin ...
Mon Mar 28 18:49:26 2011: Setting preliminary keymap...done.
Mon Mar 28 18:49:26 2011: Activating swap...done.
Mon Mar 28 18:49:26 2011: Checking root file system...fsck from util-linux-ng 2.17.2
Mon Mar 28 18:49:26 2011: /dev/sda1: clean, 22584/217728 files, 189905/870144 blocks
Mon Mar 28 18:49:26 2011: done.
Mon Mar 28 18:49:26 2011: Cleaning up ifupdown....
Mon Mar 28 18:49:26 2011: Loading kernel modules...done.
Mon Mar 28 18:49:26 2011: Setting up networking....
Mon Mar 28 18:49:26 2011: Activating lvm and md swap...done.
Mon Mar 28 18:49:26 2011: Checking file systems...fsck from util-linux-ng 2.17.2
Mon Mar 28 18:49:26 2011: done.
Mon Mar 28 18:49:26 2011: Mounting local filesystems...done.
Mon Mar 28 18:49:26 2011: Activating swapfile swap...done.
Mon Mar 28 18:49:26 2011: Cleaning up temporary files....
Mon Mar 28 18:49:26 2011: Setting kernel variables ...done.
Mon Mar 28 18:49:26 2011: Configuring network interfaces...done.
Mon Mar 28 18:49:26 2011: Starting portmap daemon....
Mon Mar 28 18:49:26 2011: Starting NFS common utilities: statd.
Mon Mar 28 18:49:26 2011: Cleaning up temporary files....
Mon Mar 28 18:49:26 2011: Setting console screen modes and fonts.
Mon Mar 28 18:49:26 2011: ^[]R^[[9;30]^[[14;30]Setting console screen modes.
Mon Mar 28 18:49:26 2011: Skipping font and keymap setup (handled by console-setup).
Mon Mar 28 18:49:26 2011: Setting up console font and keymap...done.
Mon Mar 28 18:49:26 2011: Setting sensors limits.
Mon Mar 28 18:49:26 2011: INIT: Entering runlevel: 2
Mon Mar 28 18:49:26 2011: Using makefile-style concurrent boot in runlevel 2.
Mon Mar 28 18:49:26 2011: Starting portmap daemon...Already running..
Mon Mar 28 18:49:26 2011: Starting NFS common utilities: statd.
Mon Mar 28 18:49:26 2011: Starting enhanced syslogd: rsyslogd.
Mon Mar 28 18:49:26 2011: Starting ACPI services....
Mon Mar 28 18:49:27 2011: Starting web server: apache2.
Mon Mar 28 18:49:27 2011: Starting periodic command scheduler: cron.
Mon Mar 28 18:49:27 2011: Starting ftp server: proftpd.
Mon Mar 28 18:49:28 2011: Starting OpenBSD Secure Shell server: sshd.

 

[feissmaik]

AW: IPC - problem nach reboot …

ist er da denn auch fehlerfrei hochgefahren?
weil so kann natürlich auch kein fehler zu erkennen sein... wenn kein fehler auftritt kann auch kein fehler gelogged werden...
(und wie die logs bei (re)boots gehandhabt werden sagte ich dir auch scho...)


und was sagt ' dmesg ' ? (5.x danach gefragt nun...)

 

[Cubelles]

Logfile

Spoiler

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-5-686 (Debian 2.6.32-31) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Tue Mar 8 21:36:00 UTC 2011
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000008f000 (usable)
[ 0.000000] BIOS-e820: 000000000008f000 - 0000000000090000 (reserved)
[ 0.000000] BIOS-e820: 0000000000090000 - 000000000009ec00 (usable)
[ 0.000000] BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000cee98000 (usable)
[ 0.000000] BIOS-e820: 00000000cee98000 - 00000000ceebf000 (reserved)
[ 0.000000] BIOS-e820: 00000000ceebf000 - 00000000cef47000 (usable)
[ 0.000000] BIOS-e820: 00000000cef47000 - 00000000cefbf000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000cefbf000 - 00000000ceff1000 (usable)
[ 0.000000] BIOS-e820: 00000000ceff1000 - 00000000cefff000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000cefff000 - 00000000cf000000 (usable)
[ 0.000000] BIOS-e820: 00000000cf000000 - 00000000d0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f8000000 - 00000000fc000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000130000000 (usable)
[ 0.000000] DMI 2.5 present.
[ 0.000000] last_pfn = 0xcf000 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-DFFFF write-protect
[ 0.000000] E0000-FFFFF uncachable
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 base 080000000 mask FC0000000 write-back
[ 0.000000] 2 base 0C0000000 mask FF0000000 write-back
[ 0.000000] 3 base 0CF000000 mask FFF000000 uncachable
[ 0.000000] 4 base 100000000 mask FC0000000 write-back
[ 0.000000] 5 base 0FFFF0000 mask FFFFF0000 write-protect
[ 0.000000] 6 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000373fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037000000 page 2M
[ 0.000000] 0037000000 - 00373fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 373fe000 @ 7000-d000
[ 0.000000] RAMDISK: 377d2000 - 37fefe8a
[ 0.000000] Allocated new RAMDISK: 00100000 - 0091de8a
[ 0.000000] Move RAMDISK from 00000000377d2000 - 0000000037fefe89 to 00100000 - 0091de89
[ 0.000000] ACPI: RSDP 000f2130 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT ceffe120 0004C (v01 INTEL D525MW 00000045 01000013)
[ 0.000000] ACPI: FACP ceffd000 000F4 (v03 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: DSDT ceff9000 03796 (v01 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: FACS cef87000 00040
[ 0.000000] ACPI: APIC ceff8000 00084 (v02 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: MCFG ceff7000 0003C (v01 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: HPET ceff6000 00038 (v01 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: SSDT ceff2000 0377C (v01 INTEL D525MW 00000045 MSFT 0100000D)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 2428MB HIGHMEM available.
[ 0.000000] 883MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 373fe000
[ 0.000000] low ram: 0 - 373fe000
[ 0.000000] node 0 low ram: 00000000 - 373fe000
[ 0.000000] node 0 bootmap 00009000 - 0000fe80
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0001000000 - 00014cabb4] TEXT DATA BSS ==> [0001000000 - 00014cabb4]
[ 0.000000] #4 [000009ec00 - 0000100000] BIOS reserved ==> [000009ec00 - 0000100000]
[ 0.000000] #5 [00014cb000 - 00014d1126] BRK ==> [00014cb000 - 00014d1126]
[ 0.000000] #6 [0000007000 - 0000009000] PGTABLE ==> [0000007000 - 0000009000]
[ 0.000000] #7 [0000100000 - 000091de8a] NEW RAMDISK ==> [0000100000 - 000091de8a]
[ 0.000000] #8 [0000009000 - 0000010000] BOOTMAP ==> [0000009000 - 0000010000]
[ 0.000000] found SMP MP-table at [c00fbe50] fbe50
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000373fe
[ 0.000000] HighMem 0x000373fe -> 0x000cf000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[6] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000008f
[ 0.000000] 0: 0x00000090 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x000cee98
[ 0.000000] 0: 0x000ceebf -> 0x000cef47
[ 0.000000] 0: 0x000cefbf -> 0x000ceff1
[ 0.000000] 0: 0x000cefff -> 0x000cf000
[ 0.000000] On node 0 totalpages: 847600
[ 0.000000] free_area_init_node: node 0, pgdat c13b28a0, node_mem_map c14d3000
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3965 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 4857 pages used for memmap
[ 0.000000] HighMem zone: 616540 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 24
[ 0.000000] PM: Registered nosave memory: 000000000008f000 - 0000000000090000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at d0000000 (gap: d0000000:28000000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 14 pages/cpu @c3000000 s34328 r0 d23016 u1048576
[ 0.000000] pcpu-alloc: s34328 r0 d23016 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 840975
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=43619c76-e51f-4972-a8b9-f3f42ad5f356 ro quiet
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (000373fe:000cf000)
[ 0.000000] Memory: 3348408k/3391488k available (2503k kernel code, 40864k reserved, 1321k data, 380k init, 2485588k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffd56000 - 0xfffff000 (2724 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB)
[ 0.000000] .init : 0xc13bd000 - 0xc141c000 ( 380 kB)
[ 0.000000] .data : 0xc1271cc1 - 0xc13bc4c0 (1321 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1271cc1 (2503 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:1280
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1799.785 MHz processor.
[ 0.004008] Calibrating delay loop (skipped), value calculated using timer frequency.. 3599.57 BogoMIPS (lpj=7199140)
[ 0.004037] Security Framework initialized
[ 0.004045] SELinux: Disabled at boot.
[ 0.004058] Mount-cache hash table entries: 512
[ 0.004242] Initializing cgroup subsys ns
[ 0.004249] Initializing cgroup subsys cpuacct
[ 0.004257] Initializing cgroup subsys devices
[ 0.004262] Initializing cgroup subsys freezer
[ 0.004266] Initializing cgroup subsys net_cls
[ 0.004301] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.004306] CPU: L2 cache: 512K
[ 0.004310] CPU: Physical Processor ID: 0
[ 0.004314] CPU: Processor Core ID: 0
[ 0.004320] mce: CPU supports 5 MCE banks
[ 0.004333] CPU0: Thermal monitoring enabled (TM1)
[ 0.004339] using mwait in idle threads.
[ 0.004348] Performance Events: Atom events, Intel PMU driver.
[ 0.004360] ... version: 3
[ 0.004364] ... bit width: 40
[ 0.004368] ... generic registers: 2
[ 0.004371] ... value mask: 000000ffffffffff
[ 0.004376] ... max period: 000000007fffffff
[ 0.004379] ... fixed-purpose events: 3
[ 0.004383] ... event mask: 0000000700000003
[ 0.004390] Checking 'hlt' instruction... OK.
[ 0.021440] ACPI: Core revision 20090903
[ 0.036091] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.036518] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.077295] CPU0: Intel(R) Atom(TM) CPU D525 @ 1.80GHz stepping 0a
[ 0.080001] Booting processor 1 APIC 0x1 ip 0x6000
[ 0.008000] Initializing CPU#1
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.008000] CPU: L2 cache: 512K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 0
[ 0.008000] CPU1: Thermal monitoring enabled (TM1)
[ 0.164137] CPU1: Intel(R) Atom(TM) CPU D525 @ 1.80GHz stepping 0a
[ 0.164152] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.168214] Booting processor 2 APIC 0x2 ip 0x6000
[ 0.008000] Initializing CPU#2
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.008000] CPU: L2 cache: 512K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU2: Thermal monitoring enabled (TM1)
[ 0.256134] CPU2: Intel(R) Atom(TM) CPU D525 @ 1.80GHz stepping 0a
[ 0.256147] checking TSC synchronization [CPU#0 -> CPU#2]: passed.
[ 0.260162] Booting processor 3 APIC 0x3 ip 0x6000
[ 0.008000] Initializing CPU#3
[ 0.008000] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 0.008000] CPU: L2 cache: 512K
[ 0.008000] CPU: Physical Processor ID: 0
[ 0.008000] CPU: Processor Core ID: 1
[ 0.008000] CPU3: Thermal monitoring enabled (TM1)
[ 0.348077] CPU3: Intel(R) Atom(TM) CPU D525 @ 1.80GHz stepping 0a
[ 0.348089] checking TSC synchronization [CPU#0 -> CPU#3]: passed.
[ 0.352059] Brought up 4 CPUs
[ 0.352065] Total of 4 processors activated (14399.72 BogoMIPS).
[ 0.353077] CPU0 attaching sched-domain:
[ 0.353085] domain 0: span 0-1 level SIBLING
[ 0.353090] groups: 0 (cpu_power = 589) 1 (cpu_power = 589)
[ 0.353101] domain 1: span 0-1 level MC
[ 0.353106] groups: 0-1 (cpu_power = 1178)
[ 0.353114] domain 2: span 0-3 level CPU
[ 0.353119] groups: 0-1 (cpu_power = 1178) 2-3 (cpu_power = 1178)
[ 0.353132] CPU1 attaching sched-domain:
[ 0.353137] domain 0: span 0-1 level SIBLING
[ 0.353141] groups: 1 (cpu_power = 589) 0 (cpu_power = 589)
[ 0.353151] domain 1: span 0-1 level MC
[ 0.353156] groups: 0-1 (cpu_power = 1178)
[ 0.353164] domain 2: span 0-3 level CPU
[ 0.353168] groups: 0-1 (cpu_power = 1178) 2-3 (cpu_power = 1178)
[ 0.353179] CPU2 attaching sched-domain:
[ 0.353184] domain 0: span 2-3 level SIBLING
[ 0.353188] groups: 2 (cpu_power = 589) 3 (cpu_power = 589)
[ 0.353198] domain 1: span 2-3 level MC
[ 0.353203] groups: 2-3 (cpu_power = 1178)
[ 0.353211] domain 2: span 0-3 level CPU
[ 0.353215] groups: 2-3 (cpu_power = 1178) 0-1 (cpu_power = 1178)
[ 0.353227] CPU3 attaching sched-domain:
[ 0.353232] domain 0: span 2-3 level SIBLING
[ 0.353236] groups: 3 (cpu_power = 589) 2 (cpu_power = 589)
[ 0.353246] domain 1: span 2-3 level MC
[ 0.353251] groups: 2-3 (cpu_power = 1178)
[ 0.353259] domain 2: span 0-3 level CPU
[ 0.353263] groups: 2-3 (cpu_power = 1178) 0-1 (cpu_power = 1178)
[ 0.353565] devtmpfs: initialized
[ 0.353565] regulator: core version 0.5
[ 0.353565] NET: Registered protocol family 16
[ 0.353565] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.353565] ACPI: bus type pci registered
[ 0.353565] PCI: MCFG configuration 0: base f8000000 segment 0 buses 0 - 63
[ 0.353565] PCI: MCFG area at f8000000 reserved in E820
[ 0.353565] PCI: Using MMCONFIG for extended config space
[ 0.353565] PCI: Using configuration type 1 for base access
[ 0.353565] mtrr: your CPUs had inconsistent variable MTRR settings
[ 0.353565] mtrr: probably your BIOS does not setup all CPUs.
[ 0.353565] mtrr: corrected configuration.
[ 0.353565] bio: create slab <bio-0> at 0
[ 0.356783] ACPI: EC: Look up EC in DSDT
[ 0.368688] ACPI: BIOS _OSI(Linux) query ignored
[ 0.369627] ACPI: Interpreter enabled
[ 0.369634] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.369678] ACPI: Using IOAPIC for interrupt routing
[ 0.376653] ACPI: No dock devices found.
[ 0.376965] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.377081] pci 0000:00:02.0: reg 10 32bit mmio: [0xe0200000-0xe027ffff]
[ 0.377090] pci 0000:00:02.0: reg 14 io port: [0x20c0-0x20c7]
[ 0.377098] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xd0000000-0xdfffffff]
[ 0.377106] pci 0000:00:02.0: reg 1c 32bit mmio: [0xe0100000-0xe01fffff]
[ 0.377233] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.377241] pci 0000:00:1c.0: PME# disabled
[ 0.377327] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.377334] pci 0000:00:1c.1: PME# disabled
[ 0.377420] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.377427] pci 0000:00:1c.2: PME# disabled
[ 0.377511] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.377519] pci 0000:00:1c.3: PME# disabled
[ 0.377607] pci 0000:00:1d.0: reg 20 io port: [0x2080-0x209f]
[ 0.377704] pci 0000:00:1d.1: reg 20 io port: [0x2060-0x207f]
[ 0.377801] pci 0000:00:1d.2: reg 20 io port: [0x2040-0x205f]
[ 0.377889] pci 0000:00:1d.3: reg 20 io port: [0x2020-0x203f]
[ 0.377968] pci 0000:00:1d.7: reg 10 32bit mmio: [0xe0280400-0xe02807ff]
[ 0.378031] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.378039] pci 0000:00:1d.7: PME# disabled
[ 0.378195] pci 0000:00:1f.0: [Firmware Bug]: TigerPoint LPC.BM_STS cleared
[ 0.378259] pci 0000:00:1f.2: reg 10 io port: [0x20b8-0x20bf]
[ 0.378269] pci 0000:00:1f.2: reg 14 io port: [0x20cc-0x20cf]
[ 0.378280] pci 0000:00:1f.2: reg 18 io port: [0x20b0-0x20b7]
[ 0.378290] pci 0000:00:1f.2: reg 1c io port: [0x20c8-0x20cb]
[ 0.378300] pci 0000:00:1f.2: reg 20 io port: [0x20a0-0x20af]
[ 0.378310] pci 0000:00:1f.2: reg 24 32bit mmio: [0xe0280000-0xe02803ff]
[ 0.378339] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.378347] pci 0000:00:1f.2: PME# disabled
[ 0.378410] pci 0000:00:1f.3: reg 20 io port: [0x2000-0x201f]
[ 0.378508] pci 0000:01:00.0: reg 10 io port: [0x1000-0x10ff]
[ 0.378537] pci 0000:01:00.0: reg 18 64bit mmio pref: [0xe0004000-0xe0004fff]
[ 0.378557] pci 0000:01:00.0: reg 20 64bit mmio pref: [0xe0000000-0xe0003fff]
[ 0.378618] pci 0000:01:00.0: supports D1 D2
[ 0.378622] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.378631] pci 0000:01:00.0: PME# disabled
[ 0.378724] pci 0000:00:1c.0: bridge io port: [0x1000-0x1fff]
[ 0.378737] pci 0000:00:1c.0: bridge 64bit mmio pref: [0xe0000000-0xe00fffff]
[ 0.378979] pci 0000:00:1e.0: transparent bridge
[ 0.379019] pci_bus 0000:00: on NUMA node 0
[ 0.379027] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.379309] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
[ 0.379486] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 0.379605] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 0.379723] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
[ 0.379840] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
[ 0.386736] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.386919] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.387101] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.387281] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.387459] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.387641] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.387823] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.388020] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12)
[ 0.388191] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.388208] vgaarb: loaded
[ 0.388249] PCI: Using ACPI for IRQ routing
[ 0.388320] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.388330] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.388340] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.400023] Switching to clocksource tsc
[ 0.402014] pnp: PnP ACPI init
[ 0.402050] ACPI: bus type pnp registered
[ 0.405449] pnp: PnP ACPI: found 13 devices
[ 0.405455] ACPI: ACPI bus type pnp unregistered
[ 0.405461] PnPBIOS: Disabled by ACPI PNP
[ 0.405482] system 00:01: iomem range 0xf8000000-0xfbffffff has been reserved
[ 0.405489] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.405496] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.405503] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.405510] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.405517] system 00:01: iomem range 0xc0000-0xdffff could not be reserved
[ 0.405524] system 00:01: iomem range 0xe0000-0xfffff could not be reserved
[ 0.405531] system 00:01: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.405546] system 00:06: ioport range 0x500-0x53f has been reserved
[ 0.405553] system 00:06: ioport range 0x400-0x47f has been reserved
[ 0.405559] system 00:06: ioport range 0x680-0x6ff has been reserved
[ 0.405567] system 00:06: ioport range 0x295-0x296 has been reserved
[ 0.440671] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01
[ 0.440679] pci 0000:00:1c.0: IO window: 0x1000-0x1fff
[ 0.440688] pci 0000:00:1c.0: MEM window: 0xe0300000-0xe06fffff
[ 0.440697] pci 0000:00:1c.0: PREFETCH window: 0x000000e0000000-0x000000e00fffff
[ 0.440707] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
[ 0.440714] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.440722] pci 0000:00:1c.1: MEM window: 0xe0700000-0xe08fffff
[ 0.440730] pci 0000:00:1c.1: PREFETCH window: 0x000000e0900000-0x000000e0afffff
[ 0.440741] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:03
[ 0.440747] pci 0000:00:1c.2: IO window: 0x4000-0x4fff
[ 0.440755] pci 0000:00:1c.2: MEM window: 0xe0b00000-0xe0cfffff
[ 0.440762] pci 0000:00:1c.2: PREFETCH window: 0x000000e0d00000-0x000000e0efffff
[ 0.440773] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:04
[ 0.440779] pci 0000:00:1c.3: IO window: 0x5000-0x5fff
[ 0.440787] pci 0000:00:1c.3: MEM window: 0xe0f00000-0xe10fffff
[ 0.440795] pci 0000:00:1c.3: PREFETCH window: 0x000000e1100000-0x000000e12fffff
[ 0.440805] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.440809] pci 0000:00:1e.0: IO window: disabled
[ 0.440816] pci 0000:00:1e.0: MEM window: disabled
[ 0.440823] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.440850] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.440859] pci 0000:00:1c.0: setting latency timer to 64
[ 0.440873] pci 0000:00:1c.1: enabling device (0000 -> 0003)
[ 0.440883] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.440892] pci 0000:00:1c.1: setting latency timer to 64
[ 0.440904] pci 0000:00:1c.2: enabling device (0000 -> 0003)
[ 0.440914] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.440923] pci 0000:00:1c.2: setting latency timer to 64
[ 0.440936] pci 0000:00:1c.3: enabling device (0000 -> 0003)
[ 0.440946] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.440954] pci 0000:00:1c.3: setting latency timer to 64
[ 0.440967] pci 0000:00:1e.0: setting latency timer to 64
[ 0.440976] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.440982] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.440988] pci_bus 0000:01: resource 0 io: [0x1000-0x1fff]
[ 0.440994] pci_bus 0000:01: resource 1 mem: [0xe0300000-0xe06fffff]
[ 0.440999] pci_bus 0000:01: resource 2 pref mem [0xe0000000-0xe00fffff]
[ 0.441005] pci_bus 0000:02: resource 0 io: [0x3000-0x3fff]
[ 0.441011] pci_bus 0000:02: resource 1 mem: [0xe0700000-0xe08fffff]
[ 0.441017] pci_bus 0000:02: resource 2 pref mem [0xe0900000-0xe0afffff]
[ 0.441023] pci_bus 0000:03: resource 0 io: [0x4000-0x4fff]
[ 0.441028] pci_bus 0000:03: resource 1 mem: [0xe0b00000-0xe0cfffff]
[ 0.441034] pci_bus 0000:03: resource 2 pref mem [0xe0d00000-0xe0efffff]
[ 0.441040] pci_bus 0000:04: resource 0 io: [0x5000-0x5fff]
[ 0.441046] pci_bus 0000:04: resource 1 mem: [0xe0f00000-0xe10fffff]
[ 0.441052] pci_bus 0000:04: resource 2 pref mem [0xe1100000-0xe12fffff]
[ 0.441058] pci_bus 0000:05: resource 3 io: [0x00-0xffff]
[ 0.441063] pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
[ 0.441130] NET: Registered protocol family 2
[ 0.441323] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.441891] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.442752] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.443152] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.443158] TCP reno registered
[ 0.443328] NET: Registered protocol family 1
[ 0.443366] pci 0000:00:02.0: Boot video device
[ 0.459976] Unpacking initramfs...
[ 0.811404] Freeing initrd memory: 8311k freed
[ 0.817544] audit: initializing netlink socket (disabled)
[ 0.817563] type=2000 audit(1301401554.815:1): initialized
[ 0.822832] highmem bounce pool size: 64 pages
[ 0.822842] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.825926] VFS: Disk quotas dquot_6.5.2
[ 0.826038] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.826172] msgmni has been set to 1703
[ 0.826624] alg: No test for stdrng (krng)
[ 0.826728] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.826734] io scheduler noop registered
[ 0.826738] io scheduler anticipatory registered
[ 0.826742] io scheduler deadline registered
[ 0.826814] io scheduler cfq registered (default)
[ 0.827004] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X
[ 0.827019] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.827210] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X
[ 0.827224] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.827408] pcieport 0000:00:1c.2: irq 26 for MSI/MSI-X
[ 0.827421] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.827611] pcieport 0000:00:1c.3: irq 27 for MSI/MSI-X
[ 0.827625] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.827912] isapnp: Scanning for PnP cards...
[ 1.181438] isapnp: No Plug & Play device found
[ 1.184155] Linux agpgart interface v0.103
[ 1.184283] agpgart-intel 0000:00:00.0: Intel IGD Chipset
[ 1.184598] agpgart-intel 0000:00:00.0: detected 8188K stolen memory
[ 1.195373] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
[ 1.195490] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.195629] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.195792] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.196278] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.196483] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.196759] PNP: No PS/2 controller found. Probing ports directly.
[ 1.199299] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.199312] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.199439] mice: PS/2 mouse device common for all mice
[ 1.199504] rtc_cmos 00:03: RTC can wake from S4
[ 1.199577] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.199614] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.199638] cpuidle: using governor ladder
[ 1.199642] cpuidle: using governor menu
[ 1.199650] No iBFT detected.
[ 1.200370] TCP cubic registered
[ 1.200644] NET: Registered protocol family 10
[ 1.202166] Mobile IPv6
[ 1.202172] NET: Registered protocol family 17
[ 1.202199] Using IPI No-Shortcut mode
[ 1.202347] PM: Resume from disk failed.
[ 1.202371] registered taskstats version 1
[ 1.202814] rtc_cmos 00:03: setting system clock to 2011-03-29 12:25:56 UTC (1301401556)
[ 1.202916] Initalizing network drop monitor service
[ 1.202962] Freeing unused kernel memory: 380k freed
[ 1.203202] Write protecting the kernel text: 2504k
[ 1.203240] Write protecting the kernel read-only data: 920k
[ 1.232842] udev[76]: starting version 164
[ 1.360549] usbcore: registered new interface driver usbfs
[ 1.360605] usbcore: registered new interface driver hub
[ 1.360706] usbcore: registered new device driver usb
[ 1.401927] SCSI subsystem initialized
[ 1.457174] libata version 3.00 loaded.
[ 1.462950] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.464583] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.464618] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 1.464627] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 1.464674] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 1.464718] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 1.464737] ehci_hcd 0000:00:1d.7: debug port 1
[ 1.468618] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 1.468650] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe0280400
[ 1.470839] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.470870] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 1.470935] r8169 0000:01:00.0: setting latency timer to 64
[ 1.470945] r8169 0000:01:00.0: unknown MAC, using family default
[ 1.471032] r8169 0000:01:00.0: irq 28 for MSI/MSI-X
[ 1.472736] eth0: RTL8168b/8111b at 0xf7f76000, 70:71:bc:bd:ce:5c, XID 0c200000 IRQ 28
[ 1.484523] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.484576] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.484584] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.484591] usb usb1: Product: EHCI Host Controller
[ 1.484597] usb usb1: Manufacturer: Linux 2.6.32-5-686 ehci_hcd
[ 1.484603] usb usb1: SerialNumber: 0000:00:1d.7
[ 1.484781] usb usb1: configuration #1 chosen from 1 choice
[ 1.484855] hub 1-0:1.0: USB hub found
[ 1.484873] hub 1-0:1.0: 8 ports detected
[ 1.485006] ata_piix 0000:00:1f.2: version 2.13
[ 1.485044] ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.485057] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 1.486341] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.637534] ata_piix 0000:00:1f.2: setting latency timer to 64
[ 1.637654] scsi0 : ata_piix
[ 1.637864] scsi1 : ata_piix
[ 1.638214] ata1: SATA max UDMA/133 cmd 0x20b8 ctl 0x20cc bmdma 0x20a0 irq 18
[ 1.638221] ata2: SATA max UDMA/133 cmd 0x20b0 ctl 0x20c8 bmdma 0x20a8 irq 18
[ 1.638279] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 1.638317] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 1.638327] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.638363] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.638421] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00002080
[ 1.638512] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.638522] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.638529] usb usb2: Product: UHCI Host Controller
[ 1.638535] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.638542] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.638743] usb usb2: configuration #1 chosen from 1 choice
[ 1.638821] hub 2-0:1.0: USB hub found
[ 1.638843] hub 2-0:1.0: 2 ports detected
[ 1.638978] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.638996] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 1.639004] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 1.639023] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 1.639072] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00002060
[ 1.639137] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.639143] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.639148] usb usb3: Product: UHCI Host Controller
[ 1.639153] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.639157] usb usb3: SerialNumber: 0000:00:1d.1
[ 1.639292] usb usb3: configuration #1 chosen from 1 choice
[ 1.639374] hub 3-0:1.0: USB hub found
[ 1.639393] hub 3-0:1.0: 2 ports detected
[ 1.639508] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 1.639521] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 1.639527] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 1.639543] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 1.639578] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002040
[ 1.639641] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.639647] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.639652] usb usb4: Product: UHCI Host Controller
[ 1.639656] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.639661] usb usb4: SerialNumber: 0000:00:1d.2
[ 1.639794] usb usb4: configuration #1 chosen from 1 choice
[ 1.639874] hub 4-0:1.0: USB hub found
[ 1.639893] hub 4-0:1.0: 2 ports detected
[ 1.640015] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 1.640027] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 1.640033] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 1.640052] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 1.640100] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00002020
[ 1.640167] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.640173] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.640178] usb usb5: Product: UHCI Host Controller
[ 1.640182] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.640187] usb usb5: SerialNumber: 0000:00:1d.3
[ 1.640321] usb usb5: configuration #1 chosen from 1 choice
[ 1.640400] hub 5-0:1.0: USB hub found
[ 1.640420] hub 5-0:1.0: 2 ports detected
[ 1.792286] ata2.01: NODEV after polling detection
[ 1.800598] ata1.00: CFA: CF CARD 4GB, Ver3.01K, max UDMA/100
[ 1.800614] ata2.00: ATAPI: TSSTcorpCD/DVDW SH-S183A, SB02, max UDMA/33
[ 1.800630] ata1.00: 7372512 sectors, multi 1: LBA
[ 1.800644] ata2.00: applying bridge limits
[ 1.808396] ata1.00: configured for UDMA/100
[ 1.808603] scsi 0:0:0:0: Direct-Access ATA CF CARD 4GB Ver3 PQ: 0 ANSI: 5
[ 1.816874] ata2.00: configured for UDMA/33
[ 1.818385] scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S183A SB02 PQ: 0 ANSI: 5
[ 1.844405] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.844414] Uniform CD-ROM driver Revision: 3.20
[ 1.844985] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.847091] sd 0:0:0:0: [sda] 7372512 512-byte logical blocks: (3.77 GB/3.51 GiB)
[ 1.847246] sd 0:0:0:0: [sda] Write Protect is off
[ 1.847255] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.847340] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 1.847836] sda: sda1 sda2 < sda5 >
[ 1.850545] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.856581] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.856671] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.994156] PM: Starting manual resume from disk
[ 1.994164] PM: Resume from partition 8:5
[ 1.994167] PM: Checking hibernation image.
[ 1.994685] PM: Error -22 checking image file
[ 1.994689] PM: Resume from disk failed.
[ 2.029093] kjournald starting. Commit interval 5 seconds
[ 2.029112] EXT3-fs: mounted filesystem with ordered data mode.
[ 2.450005] udev[361]: starting version 164
[ 2.614334] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 2.614359] ACPI: Sleep Button [SLPB]
[ 2.615852] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 2.619588] Monitor-Mwait will be used to enter C-1 state
[ 2.619713] processor LNXCPU:00: registered as cooling_device0
[ 2.619991] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 2.620010] ACPI: Power Button [PWRF]
[ 2.637707] processor LNXCPU:01: registered as cooling_device1
[ 2.642426] processor LNXCPU:02: registered as cooling_device2
[ 2.650663] processor LNXCPU:03: registered as cooling_device3
[ 2.798616] [drm] Initialized drm 1.1.0 20060810
[ 2.818048] parport_pc 00:08: reported by Plug and Play ACPI
[ 2.818119] parport0: PC-style at 0x378, irq 7 [PCSPP]
[ 2.821954] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.917854] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 2.917864] pci 0000:00:02.0: setting latency timer to 64
[ 2.933446] pci 0000:00:02.0: irq 29 for MSI/MSI-X
[ 2.933577] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2.958648] Error: Driver 'pcspkr' is already registered, aborting...
[ 3.253183] Adding 202744k swap on /dev/sda5. Priority:-1 extents:1 across:202744k
[ 3.332433] EXT3 FS on sda1, internal journal
[ 3.370556] loop: module loaded
[ 3.895109] r8169: eth0: link up
[ 3.895121] r8169: eth0: link up

 

[TommyH99]

AW: IPC - problem nach reboot …

kannst du bitte einen SPOILER machen ... grrr

danke

 

[feissmaik]

AW: IPC - problem nach reboot …

oke das war also die ausgabe von ' dmesg ' ?
was für logs hast du denn noch? -> ls -la /var/log/

weil wie gesagt - wenn der rechner sauber hochfährt also ohne fehlermeldung, wird in den aktuellen logs auch keine fehlermeldung zu finden sein...


wie gesagt², werden bei einem standard linuxsystem die alten logdateiein umbenannt und später sogar gepackt etc - also nur du kannst herrausfinden in welcher dieser datein ein fehler stehen könnte weil nur du weisst wieviel reboots du seit dem letzten fehler hattest o.ä....

 

[Cubelles]

-> ls -la /var/log/

 

[feissmaik]

AW: IPC - problem nach reboot …

Ja guck... da sehe ich doch schomal ne dmesg.0 von 14:07... und die anderen wurden schon gepackt... -> cp /var/log/dmesg.3.gz /tmp ; cd /tmp ; gunzip -d dmesg.3.gz ; cat dmesg.3

 

[Cubelles]

dmesg.RAR !

 

[feissmaik]

AW: IPC - problem nach reboot …

Anhand der dmesg logs erkennt man leider nichts - die Frage wäre dabei immernoch ob da überhaupt ein Log dabei ist, wo er beim Booten stehen geblieben ist - diese Tatsache kannst immernoch nur Du feststellen oder eben so oft rebooten bis der fehler wieder auftritt etc aber ich wiederhole mich schon wieder....

also wirds langsam auch egal - verbau deine SSD und gut is...

 

[Cubelles]

Re: AW: IPC - problem nach reboot …

also wirds langsam auch egal - verbau deine SSD und gut is...

hast ja recht ...

was würdest du denn empfehlen Ubuntu oder Debian ?


gruß

 

[feissmaik]

AW: IPC - problem nach reboot …

auf jedenfall Debian....

Sie müssen registriert sein, um Links zu sehen.

ist ne Abwandlung von Debian also basiert ebenfals darauf aber wurde nochmals speziel für Benutzeroberflächen (KDE/GNOME) optimiert - und das ist für CS eigentlich völlig unnötig... Wenn du Linux als Windoof Ersatz kennenlernen willst, dann installier dir lieber was über ne VM an deinem richtigen PC oder boote da ne LiveCD o.ä.....