( gelöst ) kann gbox vom feed nicht installieren. Fehlermeldung: install failed

# SoftCam EMM Log configuration
#
# Save EMM data
# 00 Don't save anything (default)
# 01 Save processed EMMs (/var/tmp/emmproc.bin)
# 02 Save rejected EMMs (/var/tmp/emmblock.bin)
# 03 Save both EMMs
L: { 00 }

# Check additional OSC Frequency !!! ONLY FOR DBOX2 !!!
# 00 No Check (default)
# >0 Check on, Value in KHz , example 8MHz=08000
# F: { 0000 }

# Check additional Baurate for ATR !!! ONLY FOR DBOX2 !!!
# 00 No Check (default)
# >0 Check on, Value in bit/s, example 81861
# B: { 0000 }

# Enable TPScrypt Support
# *0 TPScrypt off
# *1 TPScrypt on (default)
# 1* don't use PTS on Viaccess cards
# 2* don't use PTS on Cryptoworks cards
# 3* don't use PTS on Viaccess and Cryptoworks cards
# 4* switch IRD to ICE mode and ICE to IRD mode
Y: { 00 }

# Empty RS232 buffer before writing
# 00 No reset
# 01 Reset Buffer (default)
E: { 01 }

# SoftCam Blocker/Filter definition
#
# 00 = Allow EMM (default for all)
# 01 = Block EMM addressed to:
# all card
# | shared address/provider
# | | unique address/hex_serial
# ----------------------------------
I: { 00 00 00 } Irdeto All SA UA
S: { 00 00 00 } Seca - SA UA
V: { 00 00 00 } Via - SA UA
N: { 00 00 00 } Nagra All SA UA
C: { 00 00 00 } Crypto All SA UA
O: { 00 00 00 } Conax - SA UA
D: { 00 00 00 } NDS All SA UA

# Timeout Definitions AND com1/com2 delays, all delays to be entered in decimal !
#T: { 00 02 02 } ATR timeout (normalX), instruction timeout (normalX)
T: { 00 02 01 } ATR timeout (normalX), instruction timeout (normalX)

# com1/com2 delays, all delays to be entered in decimal !
#
# Do NOT touch !!!!!!!!!!!!!!!!!!
# all timings should be 0, change only if you have problems.
T: { 01 00000 000 } Irdeto : byte delay (1e-6 s), instruction delay (1e-3 s)
T: { 02 00000 000 } Seca
T: { 03 00000 000 } Viaccess
T: { 04 00000 000 } Nagra
# T: { 04 00002 000 } Nagra
T: { 05 00000 000 } CryptoWorks
T: { 06 00000 000 } Geldkarte
T: { 07 00000 000 } Conax
T: { 08 00000 000 } NDS
# T: { 09 00000 000 } Dreamcrypt/Firecrypt

# Use Crypto card bug to decode any CW, no matter of chid
#
# Cxxx configuration (is aktiv for the provider only if a config line is present)
# (ECM sample to be used to get the cw's with Cxxx)
#
# Provider provider chid - that is present on the card for that provider
# || || || ||
# Digiturk
# 8: { C1 } A4 4C 00 00 31 28 00 2E 83 01 C1 8C 03 89 19 19 8E 02 00 00 8F 01 A9 91 01 55 DB 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DF 08 00 00 00 00 00 00 00 00

# Use constant CW's for
# caid pid CW0 ... CW1 ...
# 0: { 26 00 10 44 { AA AA BB 0F BB CC CC 53 AA AA BB 0F BB CC CC 53 }} #BBC ONE (27W)
# 0: { 26 00 00 03 { 15 9A CD 7C EB F6 14 F5 15 9A CD 7C EB F6 14 F5 }} #MGM ME (10E)
# 0: { 26 00 1a f6 { 12 34 56 9C 78 9A BC CE 12 34 56 9C 78 9A BC CE }}