DM 800 HD se Bootet nur bis " 192.168.2.105 Hilfe.

[pera457]

AW: DM 800 HD se Bootet nur bis " 192.168.2.105 Hilfe.

Ja habe ich mit Dreamup gemacht. Er verbindet zwar mit der Dreambox und lädt auf Rahm und bleibst stehen geht nicht weiter

 

[Bodo-1]

AW: DM 800 HD se Bootet nur bis " 192.168.2.105 Hilfe.

warum nimmst nicht die Lan Kabel und verbindest alles ?

 

[pera457]

AW: DM 800 HD se Bootet nur bis " 192.168.2.105 Hilfe.

Das Lankabel ist bereits mit der Dreambox verbunden. Und Dreambox ist verbunden mit dem Router

 

[pera457]

AW: DM 800 HD se Bootet nur bis " 192.168.2.105 Hilfe.

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.01.13 23:29:32 =~=~=~=~=~=~=~=~=~=~=~=

Spoiler

BCM74130011
012
K1
K2

K3

K4

K5

Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000005
WC1=00000012
RC2=00000018
WC2=00000036
RC3=0000000E
WC3=FFFFFFEE
RC4=0000000E
WC4=00000037
NWC=00000012
RC5=00000006
WC5=00000012
RC6=00000018
WC6=00000012
NRC=0000000F
RW=00000013
WW=0000004A
G=00000000 R=0000000F W=00000012
BL=00000000
RC1=00000002
RC2=00000015

BL=00000001
RC1=00000002
RC2=00000018

BL=00000002
RC1=00000006
RC2=00000014

BL=00000003
RC1=00000007
RC2=00000018

BL=00000004
RC1=00000006
RC2=00000014

BL=00000005
RC1=00000004
RC2=00000018

BL=00000006
RC1=00000005
RC2=00000019

BL=00000007
RC1=00000009
RC2=00000019
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.

Dreambox D M800SE

FIRST STAGE 1.0/400 {BO23456}
[m

2ND STAGE OK, build #84 (2011-09-01)

0.000 - BCM board setup
0.000 - fp init
0.000 - ca init
0.520 - load config
0.546 - config loaded.
* press to enter setup
OLED found!
color oled reset
lcd: BOOT #84
P23 detected!
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . | / - \ | / - \ | / - \ done.

find_inode failed for name=secondstage.conf

load: Failed to find inode

- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 315426
Supported modes: NTSC !NTSC_J !NTSC_443 !PAL_B !PAL_B1 !PAL_D !PAL_D1 PAL_G !PAL_H !PAL_K !PAL_I !PAL_M !PAL_N !PAL_NC !PAL_60 !SECAM_L !SECAM_B !SECAM_G !SECAM_D !SECAM_K !SECAM_H 1080i 720p 480p 1080i_50Hz !1250i_50Hz 720p_50Hz 576p_50Hz DVI_640x480p !DVI_640x480p_CVT !DVI_1280x720p_50Hz !DVI_1280x720p !DVI_1280x720p_Red !DVI_640x480p_66Hz !DVI_640x480p_70Hz !DVI_640x480p_72Hz !DVI_640x480p_75Hz !DVI_640x480p_85Hz !DVI_1280x720p_70Hz !DVI_1280x720p_72Hz !DVI_1280x720p_75Hz !DVI_1280x720p_85Hz
best supported mode is 25
using 1920x1080i (50.00 Hz)
HDMI
using colorspace: 1
create surface 1920 1080
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
parsing JPEG header..
Virtual FB Size: 1280x720
lcd: /flash/vmlinux.gz
executing '/flash/vmlinux.gz' returned: -2
waiting for link...
waiting for DHCP...
no server address given
using dhcp address
no tftp server address was specified, neither manually nor via dhcp. aborting tftp.
lcd: /boot/zImage.elf
find_inode failed for name=zImage.elf

load: Failed to find inode

no valid boot source found. press any key to enter setup.
lcd: *** STOP ***