AW: zurück zu Spark , Display zeigt nur noch Load ud Err
So , habe jetzt eine Uboot.bin (512KB) übertragen , immer noch die gleiche Problematik , siehe Log:
Escape habe ich auch mal kurz gedrückt.
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 74 a7
Hit ESC to stop autoboot: 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
** Bad Magic Number 0xffffffff **
## Booting image at 80000000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCC
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 74 a7
Hit ESC to stop autoboot: 5
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force rs232 upgrade u-boot, need 524288 Bytes(512kB)
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
Und hier beide Logs beim anwählen per Auf und Abtaste:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 74 a7
Hit ESC to stop autoboot: 0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
** Bad Magic Number 0xffffffff **
## Booting image at 80000000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
CCCCCCCCCC
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 74 a7
Hit ESC to stop autoboot: 5
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force rs232 upgrade u-boot, need 524288 Bytes(512kB)
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1-g057e7c28 (Oct 21 2011 - 09:58:11) - stm23_0043 - YW 1.0.021 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 07 00 00 74 a7
Hit ESC to stop autoboot: 5
Force command mode:Select boot (current boot system : enigma2):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark default