stocken bei gbox 802 und v13

[schnuffy1de]

Also, ich habe eine Octagon 1018 SF mit dem Image 36 FullUsb.
Schwarze V13 mit der GBox 802.
Die Aussetzer (nur SKY HD und HD+) kommen unregelmäßig, dauern 3-5 Sekunden.
Bild bleibt stehen, Ton ist weg. Anschließend geht es normal weiter.
Ich habe den Eindruck, je länger der Sender drauf ist, desto häufiger kommen diese Aussetzer.


Hier die CWshare:

# allow maximum 06 share level for recieved card data
#I: { 06 }


# 01 repeat EMM's
# 00 consider every EMM only once
# 01 restart pid on overflow
# 1* reset ENX on every channel change
# 2* rezap after start (calling pzapit -rz --pal)
# *1 check/reset ENX freezes on FTA
# *2 check/reset ENX freezes on PayTV
# *3 check/reset ENX freezes on FTA and PayTV
# 00 write nothing in atack.txt
# 01 write into atack.txt: password is wrong
# 02 write into atack.txt: ID unknown
# 04 write into atack.txt: IP is wrong
# 08 write into atack.txt: port is worng
# 10 write into atack.txt: share.stat
# 20 create online.log for online/offline logging
# 3F write everything. (combine bits for other combinations)
# 4000 send ecm again after 4 Seconds if no reply.
# 6000 resync decode after 6 Seconds if net decode failed
#N: { 00 01 03 1F 4000 6000 }
N: { 01 01 10 3F 2700 3000 }
#N: { 00 00 00 00 4000 6000 }


# Send ECM's at maximum 5 cards (please use this as default)
#X: { 05 }


# Send ECM's in any case to these card ID's, even they are more then X:
# some examples ...
#G: { 17020000 1234 }






# For W: please read the cwshare.txt, here only some examples (max. 128 PID)
# use card 1 only for the following pids
#W: { 01 02 02 } 1022 100A 100B 102B 1009 101D 1029 1014 1011 101B
# don't use card 2 for the following pids
#W: { 02 03 03 } 1008 1016


# S: is the same as W:, just using the SID instead of the ECMPID (max. 128 SID)


# cwshare.cfg sharing parameters
# M: { hostname { password }}
# D: { hostname { rx_port tx_port { password { loc_code net_code }}}}
#
# loc_code: bit 7 6 5 4 3 2 1 0
#     0 0 0 0 | | | |
#     +-+-+-+- level
#
# net_code: bit 7 6 5 4 3 2 1 0
#     0 0 0 | | | | |
#     | +-+-+-+- level
#     +--------- drop level zero cards
# example: D: { friend1.homeip.net { 8010 8020 { B142AB11 { 05 15 }}}}

# gbox config file


# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 01 10 } 127.0.0.1 8024


# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 01 }


# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
# 1X show ca access
# 2X use nagra aladin 1801 in betacrypt mode (for UM-I02)
C: { 02 }


# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 00 }


# Auto Update
# 00 is ignored (default)
# 01 enable AU
# 02 Auto AU !!!!! always use this !!!!!
A: { 01 }


# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }


# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }


# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }


# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 } 192.168.0.111


# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 } 127.0.0.1 7025


# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
(in the dbox2 the gbox writes directly the CWs, 00 is the
recommended mode ! No drivers are required) use D* ** ONLY if
you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x* invert CTS detection on com2
#V: { 00 05 } // smargo
V: { F0 30 } // sci0 und sci1
#V: { 00 35 } // sci0 und sci1 und smargo




# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
R: { 00 }


# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
W: { 00 00 } 9600


# ================================================== ===========================
# extra options to override default seting in case you expirience Problems,
# normaly these setings are not required.


# GboxTwin mode
# this options for the 2nd gbox ONLY
# you must have an extra gbox, gbox_cfg and cwshare.cfg running on /tmp,
# all other files can linked to the org. files
#F: { A6 } 5


# cpu, api, cw write method
# 00 auto
# 01 80X86
# 02 MPC823
# 03 IBM STB04xxx
# 00 auto
# 01 ibm
# 02 api2
# 03 api3
# 00 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= use internal routine (only dbox2)
# 01 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= CA_SET_DESCR type1 (dbox2, vdr)
# 02 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= CA_SET_DESCR type2
# 03 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= CA_SET_DESCR type3
# 04 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= 16 byte /proc/bus/gtx
# 05 cw write st[COLOR=red][B]<x>[/B][/COLOR]yle= 4096 byte /proc/bus/gtx, cw offset=0x04D0
# xx write cw in 1st device with index=xx
# yy write cw in 2nd device with index=yy
# 01 means with .index=0 (default)
# 02 means with .index=1
# 03 means with .index=0 and .index=1
# .. any bitwise combination ...
# FF means with all 8 indexes (0-7)
#J: { 00 03 01 00 00 }


# Files, folders, devices
# folder/device comment
#F: { 01 } /var/tmp/pmt.gbx     // pmt file
#F: { 02 } /var/tmp/emm.info     // key update log file
#F: { 03 } /var/tmp/ecm.info     // ecm info file
#F: { 04 } /var/tmp/atack.txt     // atack info file
F: { 08 } 1     // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
F: { 11 } /var/keys     // folder for config files
#F: { 12 } /var/tmp     // folder for temporary file
#F: { 13 } /var/keys     // folder for keyfiles
#F: { 21 } /dev/null     // ca device
#F: { 22 } /dev/null     // dvr device
#F: { 23 } /dev/null     // demux device
#F: { 31 } /dev/null     // second ca device to write cw's (recording)
#F: { 41 } /dev/sci0     // STB04xxx slot1
#F: { 42 } /dev/sci1     // STB04xxx slot1
#F: { 43 } /dev/ttyUSB0     // rs232 com1
#F: { 44 } /dev/ttyUSB1     // rs232 com2


########### change for IRD firmware ################
#F: { 01 } /tmp/pmt2_1.tmp
#F: { 02 } /tmp/emm.info
#F: { 03 } /tmp/ecm.info
#F: { 04 } /tmp/atack.txt
#F: { 12 } /tmp
#F: { 21 } PTI1
#F: { 22 } PTI1
#F: { 23 } PTI1
################################################## #########




# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 02 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
F: { 58 } 06 // nds


# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1


# set stay alive ping time in seconds (default is 300)
F: { A0 } 300


# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
#F: { A1 } 0

Hier die nds --> meine serial habe ich gerade rausgenommen


################################################## ##################
# [CAS] Videoguard Boxkey/Camkey
# UA - card unique address (4 byte)
# BX - boxkey (4 byte)
# CX - hwkey (16 byte)
# DX - ekpair (16 byte)
# EX - aeskey (16 byte)
#
B: { xx xx xx xx{ B0 B1 B2 B3 }}
# old format:
# N UAUAUAUA B0B1B2B3
#
# example Sky V13 -
# N 01234567 00000000
#
# set hwkey and ekpair for overcrypt step dcw = overcrypt(ccw,hwkey,ekpair)
# C: { UA UA UA UA { C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF { D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF }}}
# set aeskey for overcrypt step dcw = overcrypt(ccw,aeskey)
# C: { UA UA UA UA { E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF }}
#

da war jetzt so ein Aussetzer.


DA kommt decode failed und dann noch


entering main loop
Error in bind CW socket
: Address already in use
lost decode, resyncing ... !!!!!!!!!!!!!!!!!!!!!!!!!
ECM: CA ID: 0x1830 Nagravision -> CA PID: 0x1AEC
ECM: CA ID: 0x1843 Nagravision -> CA PID: 0x19EC
*ECM: CA ID: 0x09C4 Videoguard (NDS) -> CA PID: 0x1BEC


mehr konnte ich nicht "einfangen", da das log so schnell weiterläuft!


Hier ist noch einer:


Card response (D3 54):
D1 B3 CC 50 56 FB 4C 9D 00 00 00 C9 00 01 22 02
00 83 0E 02 01 00 0F 04 00 00 00 00 20 04 00 00
00 00 25 11 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 2A 83 98 8D DD E2 5F C8 67 0A 96
A3 E1 3D 7A 58 D7 E8 BE 0C 0B
decode failed
decode failed (4214 ms)
lost decode, resyncing ... !!!!!!!!!!!!!!!!!!!!!!!!!
ECM: CA ID: 0x1833 Nagravision -> CA PID: 0x18BC
ECM: CA ID: 0x1834 Nagravision -> CA PID: 0x1CBC
*ECM: CA ID: 0x09C4 Videoguard (NDS) -> CA PID: 0x1BBC
ECM: CA ID: 0x09C7 Videoguard (NDS) -> CA PID: 0x1DBC
ECM: CA ID: 0x09AF Videoguard (NDS) -> CA PID: 0x1FBC
ECM: CA ID: 0x1861 Nagravision -> CA PID: 0x19BC
**** hashTableECM 1 elements ****
**** hashTableEMM 0 elements ****
-ECM----------------------

in der cwshare.cfg hab ich das auch schon probiert
ist ecm timeout und resent ecm
N: { 01 01 10 3F 2700 3000 }