Heute beim einschalten blieb mein Pingu auf "boot" stehen. Ich hab ein paar Minuten gewartet dann über Netzschalter an/ausgeschaltet. Keine Änderung. Flashen startet bei Spark und Enigma, aber bleibt dann bei "5199" stehen. Wenn ich ihn jetzt nur einschalte bleibt er bei "Load" stehen. Ich habe alle erdenklichen spark und enigma versionen inklusive dem 1.29 helppack ausprobiert. Kein Glück.
Hilfe?
Log über Hyperterminal:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0a fb
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
Hat mal jemand eine U-Boot.bin oder eine andere Idee?
So sieht es beim update per Stick aus bis "5199" erscheint:
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0a fb
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading spark/mImage
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.....................
5140251 bytes read
Un-Protect Flash Bank # 1
................................................................................
....................................................... done
................................................................................
................................ done
Erased 112 sectors
Copy to Flash...
Hilfe?
Log über Hyperterminal:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0a fb
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Bad Magic Number
## Ready for binary (ymodem) download to 0x80000000 at 115200 bps...
Hat mal jemand eine U-Boot.bin oder eine andere Idee?
So sieht es beim update per Stick aus bis "5199" erscheint:
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 0a fb
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
Force Factory mode
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
reading spark/mImage
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
................................................................................
.....................
5140251 bytes read
Un-Protect Flash Bank # 1
................................................................................
....................................................... done
................................................................................
................................ done
Erased 112 sectors
Copy to Flash...
Zuletzt bearbeitet von einem Moderator: