oscam.conf
[global]
logfile = /var/log/oscam.log
failbantime = 60
failbancount = 5
cachedelay = 10
nice = -1
preferlocalcards = 1
saveinithistory = 1
dropdups = 1
resolvegethostbyname = 1
[monitor]
nocrypt = 192.168.1.1-192.168.1.254
hideclient_to = 15
monlevel = 4
appendchaninfo = 1
[cccam]
port = XXXXX
reshare = 1
version = 2.1.3
[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = MP
[webif]
httpport = 8080
httphelplang = it
httpuser = XXXXXX
httppwd = XXXXXX
httpscript = path
httprefresh = 15
httpallowed = 0.0.0.0-255.255.255.255
OSCAM.DVBAPI
#
# dvbapi configuration
#
# types:
# P - Priority
# format:
# P: <caid>:[<provider>]:[<srvid>]:[<ecmpid>]
# I - Ignore
# format:
# I: <caid>:[<provider>]:[<srvid>]:[<ecmpid>]
# M - Map
# format:
# M: <caid>:[<provider>]:[<srvid>]:[<ecmpid>] <target caid>:[<target provider>]
# D - Delay
# format:
# D: <caid>:[<provider>]:[<srvid>]:[<ecmpid>] <delay (ms)>
#
#
#P: :::1BCD # prioritize ecm stream with pid 1BCD on any channel
#P: 1722 # prioritize 1722
#P: 1830::EF75 # prioritize 1830 on channel EF75 only
#M: 1830 1830:003411 # map caid 1830 always to provider 003411
#D: 1702 200 # wait 200ms before writing cw on caid 1702
#I: :002000 # ignore provider 002000 on every channel
#I: 0 # ignore every caid that was not handled before
#P: 0500:023800 # prioritize 0500 with provider 023800
I: 1802
I: 1803
I: 1804
P: 1805
# NON TOGLIERLO !! ( da' la precedenza alla card locale)
# P: 093B
# P: 183D
# for new oscam with liboscam-stapi => 0.06
# LIVE
##s: PTI2 pmt.tmp
# TIMESHIFT
##s: PTI pmt1.tmp
# PIP
##s: PTI3 pmt2.tmp
# TERRESTRIAL
# RECORD
#s: PTI pmt.tmp
#s: PTI1 pmt.tmp
#s: PTI2 pmt.tmp
#s: PTI3 pmt.tmp
#s: PTI4 pmt.tmp
#s: PTI pmt1.tmp
#s: PTI1 pmt1.tmp
#s: PTI2 pmt1.tmp
#s: PTI3 pmt1.tmp
#s: PTI4 pmt1.tmp
#s: PTI pmt2.tmp
#s: PTI1 pmt2.tmp
#s: PTI2 pmt2.tmp
#s: PTI3 pmt2.tmp
#s: PTI4 pmt2.tmp
OSCAM.SERVER
# Definisce il reader locale o remoto: device = <device|bus:device|device:slot>|Serial:Reader serial|<ip|hostname>,<port>[,<lport>]|pcsc|<0|1>|constantcw
device = /dev/sci0
# Abilita il reader; default 1 (abilitato)
enable = 1
# reader [de]assignment to service group, default=none
services =
# 1 = ignore caid and ident settings of reader due faulty clients, default:0
disableserverfilter = 0
# Nome del reader
label = premium
# description of reader, default:none
description = Reader interno /dev/sci0 M7P
# 1 = define reader as fallback, standard and fallback reader must have the same group, default:0
fallback = 0
# set cache exchange mode
# 0: disable cache exchange mode (default)
# 1: enable cache exchange pull mode
# 2: enable cache exchange push mode for camd 3.5x and CCcam protocol
# 3: enable reverse cache exchange push mode for camd 3.5x and
# CCcam protocol
# Identical cache exchange modes must be set on local OSCam server and remote OSCam user asccount.
#cacheex = 0
# Definisce il card ID
caid = 1805
# 1 = exclude reader from auto AU, default:0
audisabled = 0
# set provider ID to use the right reader for auto AU example: auprovid = 123456
#auprovid = provider ID
# set valid ECM length per CAID and ident in hex, default:none,ident=000000 example: ecmwhitelist = 10,20,0a,0b ecmwhitelist = 0100:10,20;0200@123456:0a,4b
# In normal operation mode this parameter is not required.
# ecmwhitelist = [CAID[@ident]:]length[,length]...[;[CAID[@ident]:]length[,length]...]...
ecmwhitelist = 1805@000000:91
# status detect of card (NONE = no detection), default:CD
detect = cd
# set standard SC frequency in units of 10 kHz, for Irdeto SC set to 600, refer to OVERCLOCKING, default:357
cardmhz = 368
# set reader frequency in units of 10 kHz, if mhz > cardmhz you are in overclocking mode, refer to OVERCLOCKING, default:357
mhz = 368
# First the SC will be initialized in normal mode. If it fails, the SC will be automatically reverted to deprecated mode,
# so that the SC speed will not be changed and the communication will remain on normal ATR speed of 9600 baud.
# 1 = use deprecated SC mode only, default:0
deprecated = 0
# reader protocol, required
protocol = internal
# set CAID and SC specific ident for reader, = <CAID>:<ident>[,ident]...[;<CAID>:<ident>[,ident]...]...
#ident = 1805:008D11
# reader assingment to groups, default:none, required
group = 1
# set EMM cache of local reader (era 1,1,15)
emmcache = 1,1,31
# number of different SIDs in ECMs allowed for an interval, default:0
#ratelimitecm = count
# number of ECMs until SC reset is performed, 0 = disabled, valid for physical readers only, default:0
#resetcycle = count
# interval for rate limit, default:0
#ratelimitseconds = seconds
# activate ratelimitecm and ratelimitseconds parameters after specified delay for specified duration in seconds, ratelimitecm and ratelimitseconds are required, default:none
#cooldown = delay,duration
# list of EMM-nanos to block (in hex w/o 0x) or all EMM-nanos, valid for physical readers only, default:none
#blocknano = nano[,nano]...|all
# 1 = block unique EMMs, default:0
blockemm-u = 0
# 1 = block shared EMMs, default:0
blockemm-s = 0
# 1 = block global EMMs, default:0
blockemm-g = 0
# 1 = block unknown types of EMMs, default:0
blockemm-unknown = 1
# block all types of EMMs by lenght, maximum 10 values, default:none
#blockemm-bylen = [length,length]...
# 1 = save unique EMMs to log file, default:0
#saveemm-u = 0|1
# 1 = save shared EMMs to log file, default:0
#saveemm-s = 0|1
# 1= save global EMMs to log file, default:0
#saveemm-g = 0|1
# 1 = save unknown types of EMMs to log file, default:0
#saveemm-unknown = 0|1
# list of EMM-nanos to save (in hex w/o 0x) or all EMM-nanos, only valid for physical readers, default:none
#savenano = nano[,nano]....|all (obsolete)
# write file (usually a copy of a file saved by savenano) to your smartcard, if no path is specified, the specified file is searched for in the configuration directory, only valid for physical readers, default:none
#readnano = [path]filename
# 1 = reject bad CWs, send "not found" instead of bad CWs, default:0
#dropbadcws = 0|1
# 1 = disable CRC for CW, default: 0
# In normal operation mode this parameter is not required. Parameter is incompatible with DVB standard.
#disablecrccws = 0|1
# the higher the value the higher the probability for reader selection, default:100, It's an divider for the average responstime.
lb_weight = 100
# RSA key for Nagravision/Tiger SCs / CAM key data for Irdeto SCs (era tiger_rsakey)
rsakey = xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
# read Nagravison records (on NCMED cards only):
# 0 = disabled (default)
# 1 = read all records with expired rights
# 2 = read records with valid rights only
nagra_read = 1
oscam.user
[account]
user = MP
pwd = XXXXXX
group = 1
au = premium
caid = 0662,1805
[account]
user = XXXXXX
pwd = XXXXXX
group = 1
uniq = 3
caid = 0662,1805
cccreshare = 0