Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

[fussballgotttt]

Hallo NeroZ.

Hübsche Anleitung. Leider ist es sehr sehr lange her, als ich das letzte mal eine derartige prozedur durchgemacht habe. Im Grunde ist es ganz simpel doch die Praxis sagt oftmals was anderes. Habe bspw. das Problem mit einem potenzielllen Client. Er nutzt eine Openbox S5 HD mit mgcamd. Ich saß gestern bestimmt 4 Stunden dran, damit er sich zu meinem Oscam Server verbinden konnte. Bis auf die Tatsache, dass er laut meinem Log irgendwann mal verbunden war, ging nichts. D.h. er bekam keinen Kanal hell.
Du hast ja oben diesen Link gepostet.

- Welche mgcamd nehme ich denn für die Openbox?
- Was ist denn nun richtig: "cccam.list oder cccamd.list"? Findet man häufig sowohl als auch. :fie:

Hier mal die essentiellen Sachen.

cccamd.list

C: xxxxxx.no-ip.org 47111 test usertest

mg_cfg

Spoiler

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 }0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 00

# network ecm timeout in seconds
K: { 02 }

# newcamd dead routes connect retry, sec
Q: { 10 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 newcamd, camd3, radegast, cccamd, gbox
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 03 } root

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 000.000.000.000 514 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 02 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-******
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 12 stapi/octagon
B: { 05 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

priority.list

# use this caid first
X: { 17 02 }
X: { 18 33 }
X: { 09 c4 }

oscam.config

Spoiler

#[newcamd]
#key = 0102030405060708091011121314
#port = 11111@09C4:000000
#keepalive = 1
#mgclient = 0

[cccam]
port = 47111
forward_origin_card = 1
version = 2.3.0
minimizecards = 1
keepconnected = 1
stealth = 0
reshare = 1
reshare_mode = 0
ignorereshare = 1
updateinterval = 240

newcamd disabled. würde es gerne nur über c-line regeln.

oscam.user

Spoiler

[account]
user = test
pwd = usertest
group = 1,2,3,4
au =
services = Sky_S02,Sky_V13_HDplus,!Sky_S02_Select_&_BlueMovie
caid = 1702,1833,09C4
betatunnel = 1833.FFFF:1702
#hostname = #dyn des users
cccmaxhops = 2
cccreshare = 0
cccignorereshare = 0

oscam.services

Spoiler

#################### Stand 12.08.2012 ###########################

# Alle SKY 1702 + 1833 SID's außer Sky-Select, BlueMovie
[Sky_S02]
caid = 1702,1833
provid = 000000
srvid = 0008,0009,000A,000B,000C,000D,000E,0010,0012,0013,0014,0015,0016,0017,0018,0019,001A,001B,001C,001D,0021,0022,0023,0024,0025,0026,0027,0029,002A,002B,0032,0034,001E,0037,0038,0039,003A,003B,003C,003D,003E,003F,0040,0041,0042,0043,0044,0046,0075,0077,007A,007B,007C,007D,007E,007F,0080,0081,0082,0083,0084,0096,0097,0098,0099,009A,009B,009C,00A8,00DD,00DE,00DF,00FC,00FD,0106,0107,0110,0111,011A,011B,0124,0125,012E,012F,0138,0139,0142,0143,014C,014D,0156,0160,016B,0175,0203,0204,0206,07FF,2EFE,3331,4461,4462,6FF1,7001,7009,700A,0071,006A,006B,0072,0070,006F,0069,007C,0076,0074,6FB8,6FB7,006E,007B,007A,00F1,00F2

[Sky_S02_Select_&_BlueMovie]
caid = 1702,1833
provid = 000000
srvid = 00FB,00FE,0105,0108,010F,0119,0123,012D,0137,0141,014B,0078,0201,0159,0163,016D,0079

######################################################################################

# Alle SKY 09C4 + 1833 SID's außer Sky-Select, BlueMovie
[Sky_V13]
caid = 09C4,1833
provid = 000000
srvid = 0008,0009,000A,000B,000C,000D,000E,0010,0012,0013,0014,0015,0016,0017,0018,0019,001A,001B,001C,001D,0021,0022,0023,0024,0025,0026,0027,0029,002A,002B,0032,0034,001E,0037,0038,0039,003A,003B,003C,003D,003E,003F,0040,0041,0042,0043,0044,0046,0075,0077,007A,007B,007C,007D,007E,007F,0080,0081,0082,0083,0084,0096,0097,0098,0099,009A,009B,009C,00A8,00DD,00DE,00DF,00FC,00FD,0106,0107,0110,0111,011A,011B,0124,0125,012E,012F,0138,0139,0142,0143,014C,014D,0156,0160,016B,0175,0203,0204,0206,07FF,2EFE,3331,4461,4462,6FF1,7001,7009,700A,0071,006A,006B,0072,0070,006F,0069,007C,0076,0074,6FB8,6FB7,006E,007B,007A,00F1,00F2

[Sky_V13_HDplus]
caid = 09C4
provid = 000000
srvid = 5273,1519,EF10,EF11,EF,14,EF15,EF74,EF75,EF76,EF77,5274,2E9A,151A,277E

[Sky_V13_Select_&_BlueMovie]
caid = 09C4,1833
provid = 000000
srvid = 00FB,00FE,0105,0108,010F,0119,0123,012D,0137,0141,014B,0078,0201,0159,0163,016D,0079

Vielen Dank vorab

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

moin,

- Welche mgcamd nehme ich denn für die Openbox?

das kann ich dir leider auch nicht sagen

cccamd.list
C: xxxxxx.no-ip.org 47111 test usertest

also ich habe cccamd bei mir drin und es funkt
mit cccam.list läuft nichts
deine C-line sieht gut aus

mg_cfg

G: { 32 } # kannste umstellen, mußte aber nicht

oscam.user

alles unnötige zum testen raus nehmen

Spoiler

[account]
user = test
pwd = usertest
group = 1,2,3,4
betatunnel = 1833.FFFF:1702
cccmaxhops = 2
cccreshare = -1
cccignorereshare = -1

oscam.config

alles unnötige zum testen raus nehmen

Spoiler

[cccam]
port = 47111
version = 2.3.0
reshare = 0

eigendlich ist ja alles so weit ganz gut.
das wichtigste ist: mgcamd nach jeder änderung neu zu starten.
oder sogar enigma neu zu starten

 

[fussballgotttt]

Moin.

Wollte nochmals ein kurzes Feedback geben. Es läuft nun endlich.

Hier mal die configs. Vlt. brauchts ja mal einer.

CLIENT: OPENBOX (S5/S6/S7) mit MgCamd 1.35 ------> SERVER: FritzBox mit Oscam

oscam.config

Spoiler

#Siehe Eintrag " version". Hier stand vorher 2.3.0 und oscam/cccam meldete sich auch als solche.
#Dies funktionierte auch ohne weiteres, nur halt nicht für den MgCamd-Client.
#Abhilfe schafft hier den Server als version 2.0.11 melden zu lassen.

[cccam]
port = 47111
forward_origin_card = 1
version = 2.0.11
minimizecards = 1
keepconnected = 1
stealth = 0
reshare = 1
reshare_mode = 1
ignorereshare = 1
updateinterval = 240

oscam.user

Spoiler

[account]
user = test
pwd = test2
group = 3,4,5
au =
services = SKY_UM,UMBasic,UMHDOption,UMHighlights,UMHighlightsHD,UMAllstars,UMAllstarsHD,UMRussland
caid = 1722,1831,1835,1838
#hostname = #dyn des users
cccmaxhops = 2
cccreshare = 1
cccignorereshare = 0

mg_cfg

Spoiler

#Siehe: Line: B

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 32 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 8080

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

#Hier gab es ebenfalls einen Konflikt. D.h. der Client konte keine Verbindung zu meinem Server aufbauen.
#Weder " autodetect", "openbox", "stapi/openbox" halfen hier. Letztendlich bringt B: { 12 } an dieser Stelle den gewünschten Effekt.

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-******
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 12 }

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

cccamd.list

Spoiler

C: xxxxxxxx.no-ip.org 47111 test test2

Die rechte für cccamd.list und mg_cfg auf 755 setzen.

MfG fussballgotttt

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

moin,

#Siehe Eintrag " version". Hier stand vorher 2.3.0 und oscam/cccam meldete sich auch als solche.
#Dies funktionierte auch ohne weiteres, nur halt nicht für den MgCamd-Client.
#Abhilfe schafft hier den Server als version 2.0.11 melden zu lassen.

kann eigendlich nur an der mgcamd 1.35 liegen
bei mir (1.38) connected er ohne probleme mit oscam/cccam 2.3.0

deine info mit box type und den rechten werde ich auf alle fälle noch in die faq einfügen

 

[Soaport]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

Hallo,

versuche seit ein paar Tage Mgcamd als Client in eine Azbox Premium+ mit mein Oscamserver zu verbinden,
bisher leider ohne Erfolg.

Eventuell kann hier mir jemand helfen.

Habe folgende Konstellation:

Oscamserver auf ein Igel-ThinClient mit Debian.
zur zeit läuft es mit Cccam 2.3.0 als Client mit dem OpenRSI Image Kernel 2.xxx ohne Probleme.
Sobald ich aber das neue Image mit dem neuen Kernel 3.4.4 installiere habe ich bei der Sky-Hd-Sender Probleme, soll angeblich am Cccam liegen.
Mit Mgcamd soll es besser laufen.

Hier Meine Config´s

Oscam.conf.

Spoiler

[global]
usrfile = /var/log/cw
logfile = /var/log/oscam.log
pidfile = /var/run/oscam.pid
WaitForCards = 1
clienttimeout = 2000
fallbacktimeout = 1000
unlockparental = 1
nice = -10
serialreadertimeout = 800
maxlogsize = 256
preferlocalcards = 1
saveinithistory = 1

[monitor]

port = 16000
nocrypt = 127.0.0.1,192.168.2.1-192.168.2.255
aulow = 30
hideclient_to = 0
monlevel = 4
appendchaninfo = 0

[cccam]

port = 40000
reshare = 0
ignorereshare = 0
version = 2.3.0
updateinterval = 240
minimizecards = 0
keepconnected = 1
stealth = 0
reshare_mode = 0

[webif]

httpport = 8888
httpuser = xxxxxxxx
httppwd = xxxxxxxx
httprefresh = 0
httpallowed = 127.0.0.1,192.168.2.1-192.168.2.255
httphideidleclients = 0
httpreadonly = 0
httpsavefullcfg = 0

[newcamd]
port = 32000@09C4:000000
key = 0102030405060708091011121314
allowed = 192.168.2.1-192.168.2.255

Oscam.server

Spoiler

# oscam.server generated automatically by Streamboard OSCAM 1.20-unstable_svn build #7315
# Read more:

Sie müssen registriert sein, um Links zu sehen.

[reader]
label = v13
enable = 1
protocol = mouse
device = /dev/ttyUSB1
caid = 09C4
boxid = 12345678
ins7e11 = 15
detect = cd
mhz = 357
cardmhz = 357
ident = 09C4:000000
group = 1
emmcache = 1,3,2

Oscam.user

Spoiler

[account]

user = monitor
pwd = xxxxxxx
group = 1

[account]
user = xxxxx
pwd = xxxxx
group = 1
monlevel = 0
au = 1
#services = skyall,HD+
cccmaxhops = 5
cccreshare = 3

[account]
user = xxxxx
pwd = xxxxx
group = 1
au = 1
#services = skyall,HD+
cccmaxhops = 5
cccreshare = 3

#( Newcamd )
[account]
User = xxxxxx
Pwd = xxxxxx
CAID = 09C4
ident = 09C4:000000
au = 1
Group = 1
MonLevel = 4
Uniq = 0

mg_cfg

Spoiler

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /usr/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 33 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-******
# 04 relook
# 05 openbox
B: { 06 }

F: { 00 }

newcamd.list

Spoiler

CWS_KEEPALIVE = yes
CWS = 192.168.xxx.xxx 32000 User passw 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS_INCOMING_PORT = 12001

cccam.list

Spoiler

C: 192.168.2.200 32000 User passw.

Vielen Dank!

Gruß, Soaport

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

hi,

welche mgcamd hast du ?

oscam.conf

Spoiler

[cccam]
port = 40000
reshare = 1
version = 2.3.0
keepconnected = 1
stealth = 0

[newcamd]
port = 32000@09C4:000000
key = 0102030405060708091011121314
keepalive = 1
allowed = 192.168.2.1-192.168.2.255

oscam.user

Spoiler

[account]
User = xxxxxx
Pwd = xxxxxx
description = newcamd
au = 1
Group = 1

mg_cfg

Spoiler

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 } # auch bei E2

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 } # benutzt cccamd und newcamd netclients

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 00 # ????

# network ecm timeout in seconds
K: { 02 }

# newcamd dead routes connect retry, sec
Q: { 10 }

# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80 # ????

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 02 } 192.168.1.3 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E: ) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 02 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-******
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
# 12 OPENBOX (S5/S6/S7)
B: { 00 }
#falls das nicht läuft, einmal durch testen und bescheid geben

# map all 180x nagra caids to 1801
# default is 01
F: { 00 }

newcamd.list

Spoiler

CWS_KEEPALIVE = yes
CWS = 192.168.xxx.xxx 32000 User passw 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS_INCOMING_PORT = 12001 #raus nehmen da du die box nur als client nutzt

cccamd.list # das d vergessen

Spoiler

C: 192.168.2.200 32000 User passw
falscher port, sollte 40000 sein

wenn möglich die 1.38 nutzen
die mg_cfg dann komplett kopieren

falls du die mgcamd 1.35 nutzt unter oscam.conf bei cccam bitte auf:
version = 2.0.11 wechseln

wichtig, nach jeder änderung mgcamd und auch oscam neu starten

 

[Soaport]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

Hallo NeroZ,

erstmal Danke für die schnelle Antwort.

Mgcamd 1.38

Funzt leider immer noch nicht.

Ich bekomme mit mgcamd einfach keine Verbindung zum Oscamserver.

Oscam.log
2012/09/16 18:53:36 0 s starting thread log_list_thread
2012/09/16 18:53:36 0 s log_list_thread thread started
2012/09/16 18:53:36 0 s >> OSCam << cardserver started, version 1.20-unstable_svn, build #7315 (i486-linux-gnu)
2012/09/16 18:53:36 0 s version=1.20-unstable_svn, build #7315, system=i486-linux-gnu, nice=-10
2012/09/16 18:53:36 0 s client max. idle=120 sec, debug level=0, filter_sensitive=1
2012/09/16 18:53:36 0 s max. logsize=256 Kb, loghistorysize=4096 bytes
2012/09/16 18:53:36 0 s client timeout=2000 ms, fallback timeout=1000 ms, cache delay=0 ms
2012/09/16 18:53:36 0 s Cannot open file "/usr/local/etc/oscam.services" (errno=2 No such file or directory)
2012/09/16 18:53:36 0 s userdb reloaded: 4 accounts loaded, 0 expired, 0 disabled
2012/09/16 18:53:36 0 s signal handling initialized (type=sysv)
2012/09/16 18:53:36 0 s can't open file "/usr/local/etc/oscam.srvid" (err=2 No such file or directory), no service-id's loaded
2012/09/16 18:53:36 0 s can't open file "/usr/local/etc/oscam.tiers" (err=2 No such file or directory), no tier-id's loaded
2012/09/16 18:53:36 0 s can't open file "/usr/local/etc/oscam.provid" (err=2 No such file or directory), no provids's loaded
2012/09/16 18:53:36 0 s can't open file "/usr/local/etc/oscam.ird" (errno=2 No such file or directory) irdeto guessing not loaded
2012/09/16 18:53:36 0 s can't open whitelist file /usr/local/etc/oscam.whitelist
2012/09/16 18:53:36 0 s can't open cacheex-matcher file /usr/local/etc/oscam.cacheex
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s monitor: initialized (fd=6, port=16000)
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s camd35: disabled
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s cs378x: disabled
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s newcamd: initialized (fd=7, port=32000, crypted)
2012/09/16 18:53:36 0 s -> CAID: 09C4 PROVID: 000000
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s cccam: initialized (fd=8, port=40000, crypted)
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s pandora: disabled
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s csp: disabled
2012/09/16 18:53:36 0 s Starting listener 0
2012/09/16 18:53:36 0 s radegast: disabled
2012/09/16 18:53:36 0 s starting thread http
2012/09/16 18:53:36 0 s http thread started
2012/09/16 18:53:36 0 s starting thread reader check
2012/09/16 18:53:36 0 s reader check thread started
2012/09/16 18:53:36 0 s starting thread check
2012/09/16 18:53:36 0 s check thread started
2012/09/16 18:53:36 0 s v13 [mouse] creating thread for device /dev/ttyUSB1
2012/09/16 18:53:36 0 s loadbalancer: can't read from file /tmp/.oscam/stat
2012/09/16 18:53:36 0 s waiting for local card init
2012/09/16 18:53:36 9AECDF0 h HTTP Server listening on port 8888
2012/09/16 18:53:38 9AEB390 r v13 [mouse] Reader initialized (device=/dev/ttyUSB1, detect=cd, mhz=357, cardmhz=357)
2012/09/16 18:53:39 9AEB390 r v13 [mouse] card detected.

Newcamd wird wie man sieht Inizialisiert.

Sobald ich auf Cccam wechsle dann geht alles keine Ahnung woran es liegen kann.

Gruß, Soaport

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

ist doch bis jetzt alles ok, aber wie geht der log weiter

 

[fussballgotttt]

Re: AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

moin,

kann eigendlich nur an der mgcamd 1.35 liegen

Jap. Musste schließlich diese Version nutzen, da die 1.38 auf der S5 zum verrecken nicht rennen wollte.

 

[Soaport]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

2012/09/16 19:12:49 9AEB390 r v13 [videoguard2] type: VideoGuard Sky Germany (09C4) FastMode
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 0046, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 005a, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 007b, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 007d, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 0081, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00c0, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00c7, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00c8, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00c9, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00ca, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00cb, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00f3, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:50 9AEB390 r v13 [videoguard2] tier: 00fa, expiry date: 2012/10/29-00:01:00
2012/09/16 19:12:54 0 s init for all local cards done
2012/09/16 19:12:54 0 s anti cascading disabled
2012/09/16 19:12:54 9AF87B0 c anonymous disconnected from 192.168.2.101
2012/09/16 19:12:54 9AF9FF0 c encrypted cccam-client 192.168.2.101 granted (AZMe, au=auto (1 reader))

Log geht bis hier und dann nicht weiter, die letzte Zeile ist die AZbox-Me (läuft mit Cccam-client)

Sobald ich auf Cccam wechsle sieht die Log so aus:

2012/09/16 19:15:22 9AF87B0 c encrypted cccam-client 192.168.2.105 granted (AZPre, au=auto (1 reader))
2012/09/16 19:15:24 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:1D5E): found (117 ms) by v13
2012/09/16 19:15:26 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:B41F): found (93 ms) by v13
2012/09/16 19:15:33 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:2151): found (92 ms) by v13
2012/09/16 19:15:40 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:AC4A): found (91 ms) by v13
2012/09/16 19:15:47 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:83C1): found (91 ms) by v13
2012/09/16 19:15:54 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:EB29): found (94 ms) by v13
2012/09/16 19:16:01 9AF87B0 c AZPre (09C4&000000/0000/EF75/58:7A3F): found (93 ms) by v13

Gruß, Soaport

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

du hast hier 2 verschiedene ip adressen
2012/09/16 19:12:54 9AF9FF0 c encrypted cccam-client 192.168.2.101 granted (AZMe, au=auto (1 reader))
2012/09/16 19:15:22 9AF87B0 c encrypted cccam-client 192.168.2.105 granted (AZPre, au=auto (1 reader))
EDIT:
und davor kommt
2012/09/16 19:12:54 9AF87B0 c anonymous disconnected from 192.168.2.101


du hast bei der newcamd.list
CWS = 192.168.xxx.xxx 32000 user passw 01 02 03 04 05 06 07 08 09 10 11 12 13 14

und in der oscam.user nur xxxxx
[account]
User = user
Pwd = passw
description = newcamd
au = 1
Group = 1

trag mal beide sachen ganau so ein

hast du die komplette mg_cfg neu eingetragen ?

 

[Soaport]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

Die 2 IP Adressen gehören zu den Boxen ... 101 ist die Me, ....105 ist die Prem.+.

die Zeile davor kommt wenn eine Box gerade nicht aktiv ist (AZbox-Me ist gerade in standby)

Bei der newcamd.list ist die IP-Adresse vom Server, port, user und password wie bei oscam.user eingetragen.

Die mg_cfg habe ich 1 zu 1 kopiert gespeichert und Oscamserver sowie Newcamd auf der Box neugestartet.

Gruß

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

die frage ist jetzt ob mgcamd auch läuft

bei der cccamd.list hast du auch eine line eingetragen
wie gesagt cccamd.list
probier mal ob die läuft (c line port auf 40000 ändern)

 

[Soaport]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

Damit wir uns nicht falsch vertehen.
Der Server ist kein Cccamserver sondern ein reiner Ocamserver.
cccam.list wahr ein Schreibfehler, in der cccamd.list habe ich bereits den port geändert.

Wie kann ich prüfen ob die C line läuft?

Gruß

 

[NeroZ]

AW: Laberthread: MGcamd mit oscam/cccam/newcamd verbinden

hab dich schon verstanden, so solls ja auch sein

verbindet sich den mgcamd jetzt mit deinem oscam server über die c-line ?