( gelöst ) freetz 7430

holli2 schrieb:

Kenne ich dich nicht vom Bpanther Forum war war da mal mit einer Kathrein 910 zugange

Zum Vergrößern anklicken....

Gismotro schrieb:

Wenn der Downgrade über Freetz geht, dann teste bitte das Update auf die aktuelle Version noch mal.

Zum Vergrößern anklicken....

Code:

Firmware extrahieren, Update vorbereiten

Firmware-Archiv extrahieren ...
./var/
./var/tmp/
./var/tmp/filesystem.image
./var/tmp/kernel.image
./var/version
./var/install
./var/.packages
./var/.config
./var/chksum
./var/info.txt
./var/content
./var/regelex
./var/signature


ERLEDIGT

Ausführen des Firmware-Installationsskripts /var/install ...

Code:

install: have Kernel 3.10.73 - set kversion '3.10' and FlashUpdateTool '/lib/modules/3.10.73/kernel/drivers/char/flash_update/flash_update.ko'
install: check and install new firmware ...
OEM=
ANNEX=B
testing acceptance for device Fritz_Box_HW218 ...
korrekt install type: mips34_128MB_vdsl_dect441_4eth_1usb_host_1ab_wlan11n_04371
device has installtype mips34_128MB_vdsl_dect441_4eth_1usb_host_1ab_wlan11n_04371
OK - accept this update for device Fritz_Box_HW218 ...
testing acceptance for device Fritz_Box_HW218 done
curr: 146.06.83  new: xx.07.12
debug: curr: 146.06.83
debug: new: "XX.07.12"
major_currFWver=146
middle_currFWver=6
minor_currFWver=83
middle_newFWver=7
minor_newFWver=12
check Firmware Version: xx.07.12
DEBUG: 7 >= 6
DEBUG: 7 > 6
Accept Firmware Version: xx.07.12
install: 3.10 check files...
read 0x2f81cc83 MACIG 0xc453de23
File already contains the checksum, verifying
[cs_calc_sum] sum 0x2f81cc83
Calculated checksum is 2F81CC83
Saved checksum is 2F81CC83
Checksum validation successful!
chksum for file /var/tmp/filesystem.image ok
size for file /var/tmp/filesystem.image ok
read 0x1e798601 MACIG 0xc453de23
File already contains the checksum, verifying
[cs_calc_sum] sum 0x1e798601
Calculated checksum is 1E798601
Saved checksum is 1E798601
Checksum validation successful!
chksum for file /var/tmp/kernel.image ok
size for file /var/tmp/kernel.image ok
install: 3.10 getting mtds to install...
install: --mtd------------------------------------------------
install: --assert---------------------------------------------
install: --addr+size------------------------------------------
install: kernel_start=0x00440000
install: kernel_size=4194304
install: kernel_image_size=2648840
install: filesystem_start=0x00840000
install: filesystem_size=50331648
install: filesystem_image_size=28208392
install: 3.10 writing commands to install...
install: check for old settings ...
set INFO led to blink (modul=7, state=4)

ERLEDIGT – Rückgabewert des Installationsskripts: 1 (INSTALL_SUCCESS_REBOOT)

Code:

Von /var/post_install generierter Inhalt:

#! /bin/sh
echo $0: start
sleep 1
killall run_clock
if ps | grep -v grep | grep -q telefon ; then killall telefon ; fi
if ps | grep -v grep | grep -q telnetd ; then killall telnetd ; fi
echo skip deleting language from env
echo MODE=update > /dev/avm_power
echo disable > /dev/watchdog
echo still running:
ps
lsmod
sleep 1
update_state=good
echo Erase mtd partitions '0' and '1' ...
/sbin/update_kernel -o /dev/mtd0
/sbin/update_kernel -o /dev/mtd1
echo Copy kernel image...
/sbin/update_kernel -i /var/tmp/kernel.image  -o /dev/mtd0
[ $? -ne 0 ] && echo failed with error "$?" && update_state=bad
echo Clean up kernel image
rm -f /var/tmp/kernel.image
echo Copy filesystem image ...
mkdir -p /var/tmp/fs
mkdir -p /var/tmp/fs_mtd
mount -t squashfs /var/tmp/filesystem.image /var/tmp/fs
mount -t yaffs2 /dev/mtdblock1 /var/tmp/fs_mtd
var_mount_squashfs=`mount | grep "/var/tmp/fs type squashfs"`
if [ -z "$var_mount_squashfs" ] ; then
    echo filesystem.image: cannot mount squashfs, trying ext2 ...
    mount -t ext2 -o loop,offset=256 /var/tmp/filesystem.image /var/tmp/fs
    if ! mount | grep -q "/var/tmp/fs type ext2" 2>/dev/null; then
    dd if=/var/tmp/filesystem.image of=/var/tmp/fsimage.ext2 bs=256 skip=1
    [ "$?" -eq 0 ] && mount -t ext2 /var/tmp/fsimage.ext2 /var/tmp/fs && rm -f /var/tmp/filesystem.image
    fi
    var_mount_ext2=`mount | grep "/var/tmp/fs type ext2"`
    [ -n "$var_mount_ext2" ] && echo filesystem.image: ... mount ext2 done
fi
var_mount_mtd=`mount | grep /dev/mtdblock1`
if [ -z "$var_mount_squashfs" ] && [ -z "$var_mount_ext2" ] ; then echo failed to mount filesystem.image ; update_state=bad; fi
[ -z "$var_mount_mtd" ] && echo failed to mount /dev/mtdblock1 && update_state=bad
if [ "$update_state" = "good" ] ; then
    echo Copy filesystem ...
    cp -R /var/tmp/fs/* /var/tmp/fs_mtd
    [ $? -ne 0 ] && echo failed with error "$?" && update_state=bad
    echo ... Copy filesystem done
fi
if [ "$update_state" = "good" ] ; then
    echo Setting linux_fs_start mirror...
    echo linux_fs_start 0 > /proc/sys/urlader/environment
else
    echo Setting linux_fs_start skipped due to errors...
fi
umount /var/tmp/fs
umount /var/tmp/fs_mtd
rmdir /var/tmp/fs
rmdir /var/tmp/fs_mtd
echo clear_id 95 >/proc/tffs
echo clear_id 96 >/proc/tffs
exit 0

Zum Vergrößern anklicken....