DVB-T USB Stick wird nicht erkannt

[toga23]

Das DVB-T USB Stick (Typ WideView WT-220U PenType Receiver (Typhoon/Freecom) gesteckt, aber es passiert nichts. Unter Telnet zeigt der Befehl dmesg. dass ein USB Gerät gesteckt und entfernt wird: usb 1-2: USB disconnect, device number 3, usb 1-2: new high-speed USB device number 4 using ehci-brcm.

Ich habe versucht unter Herunterladbare Plugins/drivers/dvb-usb-dtt200u der Treiber zu laden, aber es kommt dei Meldung:
Collected errors :
* satisfy_dependencies_for: Cannot satisfy the following dependencies for enigma2-plugin-drivers-dvb-usb-dtt200u:
* kernel-module-dvb-usb-dtt200u *
* opkg_install_cmd: cannot install package enigma2-plugin-drivers-dvb-usb-dtt200u.
Ausführung beendet

Zur Info, die updates vom 30.09 und 01.10 sowie Bootloader von 24.09 sind darauf gespielt.

 

[randysoft]

AW: DVB-T USB Stick wird nicht erkannt

Besser wäre das Image neu flashen.

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

Habe das Image vom 01.10 neu geflasht. Keine Änderung.

 

[Daggi_Duck]

AW: DVB-T USB Stick wird nicht erkannt

Meine Frage nach den verwendbaren USB/DVB-T Sticks:

https://www.digital-eliteboard.com/340717-info-agonis-image-4-2-vom-30-09-2014-a-2.html#post2388023

wurde leider auch nicht beantwortet. Die Frage dort ist wohl in dem Durcheinander bei den Firmware-Updates einfach untergegangen.

 

[randysoft]

AW: DVB-T USB Stick wird nicht erkannt

@toga, mach mal update, sollte nun funktionieren.

@daggi, keine Ahnung ich nutze einen Terratec der funktioniert.

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

Update gemacht, keine Änderung.

 

[Daggi_Duck]

AW: DVB-T USB Stick wird nicht erkannt

...
@daggi, keine Ahnung ich nutze einen Terratec der funktioniert.

Welchen Terratec USB/DVB-T Stick denn genau??? Es gibt z.Z. folgende USB/DVB-T Sticks von Terratec:

Artikel-Nr. 10678 TerraTec Cinergy T Stick Dual RC
Artikel-Nr. 145258 TerraTec Cinergy DVB-T Stick
Artikel-Nr. 145259 TerraTec Cinergy Mini Stick HD
Artikel-Nr. 10684 TerraTec T1
Artikel-Nr. 10071 TerraTec Cinergy T²
Artikel-Nr. 10723 TerraTec Cinergy HTC Stick HD
Artikel-Nr. 10629 TerraTec T5
Artikel-Nr. 10631 TerraTec H7

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

@randysoft: welcher Chipset hat dein Stick?

 

[randysoft]

AW: DVB-T USB Stick wird nicht erkannt

Hi, toga es gibt ein neues Image.
Solltest Du nochmal testen.


Mein Stick: TerraTec Cinergy T USB XE

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

Neues Image raufgespielt, keine Änderung.

 

[randysoft]

AW: DVB-T USB Stick wird nicht erkannt

Immer noch gleicher Fehler ?
Funktionierte der den jemals mit Agonis ? Wenn ja mit welchem Image ?

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

Ja, immer noch der gleicher Fehler.

Nein, es hat noch nicht funktioniert.

 

[randysoft]

AW: DVB-T USB Stick wird nicht erkannt

dmesg bitte
Nachdem es eingesteckt wurde.

 

[toga23]

AW: DVB-T USB Stick wird nicht erkannt

dmesg:

Spoiler

Switching to clocksource upg
cfg80211: Calling CRDA to update world regulatory domain
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.21)
msgmni has been set to 566
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
sata_brcmstb 0000:01:00.0: version 4.0
__clk_enable: sata [1]
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
sata_brcmstb 0000:01:00.0: setting latency timer to 64
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
Broadcom 9xxxx mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
NOR chip too large to fit in mapping. Attempting to cope...
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
Reducing visibility of 8192KiB chip to 2048KiB
Broadcom 9xxxx mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001000
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
Creating 6 MTD partitions on "Broadcom 9xxxx mapped flash":
0x000000000000-0x000000400000 : "avail0"
0x000000400000-0x000000480000 : "cfe"
0x000000480000-0x0000007e0000 : "splash"
0x0000007e0000-0x0000007f0000 : "macadr"
0x0000007f0000-0x000000800000 : "nvram"
0x000000000000-0x000000800000 : "Norcomplete"
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:25:ff:05:5a:92)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver smsc75xx
usbcore: registered new interface driver smsc95xx
usbcore: registered new interface driver gl620a
usbcore: registered new interface driver net1080
usbcore: registered new interface driver plusb
usbcore: registered new interface driver cx82310_eth
usbcore: registered new interface driver cdc_ncm
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8: ST500LM012 HN-M500MBB, 2AR10002, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST500LM012 HN-M5 2AR1 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver btusb
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
sd 0:0:0:0: [sda] 4096-byte physical blocks
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Key type dns_resolver registered
EBI CS1: setting up NAND flash (primary)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000000
B4: NandSelect=50000200, nandConfig=18152300, chipSelect=1
brcmnand_read_id: CS1: dev_id=01d3d195
After: NandSelect=50000200, nandConfig=18152300
Block size=00020000, erase shift=17
NAND Config: Reg=38152300, chipSize=1024 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
timing1 not adjusted: 5363444f
timing2 not adjusted: 00000fc6
eccLevel=15, 1Ksector=0, oob=16
nbrBitsPerCell=2, cellinfo=0, chip->cellinfo=00000000
BrcmNAND mfg 1 d3 SPANSION_S30ML08GP_08 1024MB on CS1

Found NAND on CS1: ACC=d7ff1010, cfg=38152300, flashId=01d3d195, tim1=5363444f, tim2=00000fc6
BrcmNAND version = 0x0302 1024MB @00000000
B4: NandSelect=50000200, nandConfig=38152300, chipSelect=1
brcmnand_read_id: CS1: dev_id=01d3d195
After: NandSelect=50000200, nandConfig=38152300
Found NAND flash on Chip Select 1, chipSize=1024MB, usable size=1024MB, base=0
brcmnand_scan: B4 nand_select = 50000200
brcmnand_scan: After nand_select = 50000200
page_shift=11, bbt_erase_shift=17, chip_shift=30, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 1024MB @00000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0007ffc0, version 0x02 for chip on CS1
Bad block table 1tbB found at page 0007ff80, version 0x02 for chip on CS1
nand_read_bbt: Bad block at 0x23860000
nand_read_bbt: Bad block at 0x239e0000
nand_read_bbt: Bad block at 0x24620000
nand_read_bbt: Bad block at 0x246e0000
nand_read_bbt: Bad block at 0x26cc0000
nand_read_bbt: Bad block at 0x3ff80000
nand_read_bbt: Bad block at 0x3ffa0000
nand_read_bbt: Bad block at 0x3ffc0000
nand_read_bbt: Bad block at 0x3ffe0000
Adjust partition Nandcomplete size from entire device to 3ff80000 to avoid overlap with BBT reserved space
Creating 4 MTD partitions on "brcmnand.0":
0x000000600000-0x00003ff00000 : "rootfs"
0x000000600000-0x00003ff00000 : "rootfs(redundant)"
0x000000000000-0x000000600000 : "kernel"
0x000000000000-0x00003ff80000 : "Nandcomplete"
PM: CP0 COUNT/COMPARE frequency depends on divisor
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
UBI: attaching mtd6 to ubi0
usb 1-1: new high-speed USB device number 2 using ehci-brcm
ata2: SATA link down (SStatus 4 SControl 300)
sda: sda1
sd 0:0:0:0: [sda] Attached SCSI disk
UBI: scanning is finished
UBI: attached mtd6 (name "rootfs", size 1017 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 8131, bad PEBs: 5, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 310272263
UBI: available PEBs: 0, total reserved PEBs: 8131, PEBs reserved for bad PEB handling: 155
ALSA device list:
No soundcards found.
UBI: background thread "ubi_bgt0d" started, PID 49
UBIFS: parse sync
UBIFS: background thread "ubifs_bgt0_0" started, PID 50
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 1010855936 bytes (964 MiB, 7961 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 085DB268-C60B-4414-BD4C-2631AF898966, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 220k freed
EXT4-fs (sda1): recovery complete
EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
core: module_layout: kernel tainted.
Disabling lock debugging due to kernel taint
Creating main VDC heap: SD 10, HD 0, 2HD 8, SD_PIP 0, HD_PIP 0, 2HD_PIP 0
===MODEL[HDE]======
LinuxDVB Driver Date (01/10/14)
LinuxDVB cimax initial completei 41
DVB: registering new adapter (linuxdvb-0)
(NULL device *): DVB: registering adapter 0 frontend 0 (SONY CDX2837 DVB-C/T/T2)...
internaltunerCnt 0 name linuxdvb-0 adapter0
DVB: registering new adapter (linuxdvb-1)
(NULL device *): DVB: registering adapter 1 frontend 1 (SONY CDX2837 DVB-C/T/T2)...
internaltunerCnt 1 name linuxdvb-1 adapter1
DVB: registering new adapter (linuxdvb-2)
DVB: registering new adapter (linuxdvb-3)
DVB: registering new adapter (linuxdvb-4)
input: UBIOX advanced remote control (native)
as /devices/virtual/input/input0
register dbox FP RTC device !
usbcore: registered new interface driver rtl8192cu
NET: Registered protocol family 10
svc: failed to register lockdv1 RPC service (errno 124).
usb 1-2: new high-speed USB device number 3 using ehci-brcm

lsusb:

Spoiler

Bus 001 Device 002: ID 0bda:8178
Bus 001 Device 003: ID 14aa:0225
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001

Stick ist Device 003

dmesg Auschnitt von mein Notebook mit stick gesteckt:

Spoiler

[ 3290.079077] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 3290.197414] usb 1-1: New USB device found, idVendor=14aa, idProduct=0225
[ 3290.197422] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 3291.061118] dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in cold state, will try to load a firmware
[ 3291.166436] dvb-usb: downloading firmware from file 'dvb-usb-wt220u-fc03.fw'
[ 3291.252596] usbcore: registered new interface driver dvb_usb_dtt200u
[ 3292.612119] usb 1-1: USB disconnect, device number 2
[ 3292.612162] dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
[ 3293.698045] usb 1-1: new high-speed USB device number 3 using ehci-pci
[ 3293.812990] usb 1-1: New USB device found, idVendor=14aa, idProduct=0226
[ 3293.813000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3293.813037] usb 1-1: Product: Digital TV Receiver
[ 3293.813040] usb 1-1: Manufacturer: Digital TV Receiver
[ 3293.813042] usb 1-1: SerialNumber: 20060503
[ 3293.814284] dvb-usb: found a 'WideView WT-220U PenType Receiver (Typhoon/Freecom)' in warm state.
[ 3293.814375] dvb-usb: will use the device's hardware PID filter (table count: 15).
[ 3293.814505] DVB: registering new adapter (WideView WT-220U PenType Receiver (Typhoon/Freecom))
[ 3293.815691] usb 1-1: DVB: registering adapter 0 frontend 0 (WideView USB DVB-T)...
[ 3293.816091] input: IR-receiver inside an USB DVB receiver as /devices/pci0000:00/0000:00:13.5/usb1/1-1/input/input9
[ 3293.816207] dvb-usb: schedule remote query interval to 300 msecs.
[ 3293.816213] dvb-usb: WideView WT-220U PenType Receiver (Typhoon/Freecom) successfully initialized and connected.
[ 3296.117226] dvb-usb: recv bulk message failed: -110
[ 3303.817274] hid-generic 0003:14AA:0226.0001: timeout initializing reports
[ 3303.817430] input: Digital TV Receiver Digital TV Receiver as /devices/pci0000:00/0000:00:13.5/usb1/1-1/1-1:1.1/input/input10
[ 3303.817721] hid-generic 0003:14AA:0226.0001: input,hidraw0: USB HID v1.10 Keyboard [Digital TV Receiver Digital TV Receiver] on usb-0000:00:13.5-1/input1

 

[Daggi_Duck]

AW: DVB-T USB Stick wird nicht erkannt

...
Mein Stick: TerraTec Cinergy T USB XE

Von dem Stick gab es zwei verschiedene Revisionen. Die ursprüngliche Revision hatte den AF9005 Chip und die Revision 2 hat den neueren AF9015 Chip. Bleibt die Frage, welche Revision dein Stick ist.