AW: Dreambox 800 Hd und Smargo läuft nicht
Ich kriegs einfach nicht hin
Welcome to CCcam 2.1.1 server
card reader /dev/sci0handled 7(7) ecms and 9(9) emmsCaid 1702 Betacrypt ACS 900 GERCardserial xxxxxxx (7f0f34)Chid 0107 - date 0xeef valid 0x2Chid 0108 - date 0xeef valid 0x2Chid 7D2B - date 0xeef valid 0x2Chid 7D24 - date 0xeef valid 0x2Chid 7D23 - date 0xeef valid 0xfeChid 61BD - date 0xeef valid 0x2Chid 04BA - date 0xeef valid 0x2Chid 04C4 - date 0xeef valid 0xfeChid 7D2C - date 0xeef valid 0x2Chid 7D2D - date 0xeef valid 0x2card reader /dev/ttsUSB0no or unknown card insertedcard reader /dev/ttsUSB1no or unknown card insertedcard reader /dev/ttsUSB2no or unknown card insertedcard reader /dev/ttsUSB3no or unknown card insertedcard reader /dev/ttsUSB4no or unknown card insertedcard reader /dev/ttsUSB5no or unknown card insertedcard reader /dev/ttsUSB6no or unknown card insertedcard reader /dev/ttsUSB7no or unknown card inserted
die config sieht so aus
# Serial reader config. Add as many as you have attached too your system
# replaces old name 'PHOENIX READER PATH', but still works.
# default is none
# optionally add readertype : phoenix,mouse,uniprog,sc8in1,
smartreader+
# (when non readertype given defaults to uniprog (e.g. for mastera))
#
# SERIAL READER : <device> <type>
#
# example
#
#SERIAL READER : /dev/tts/0
SERIAL READER : /dev/ttsUSB0
smartreader+
SERIAL READER : /dev/ttsUSB1
smartreader+
SERIAL READER : /dev/ttsUSB2
smartreader+
SERIAL READER : /dev/ttsUSB3
smartreader+
SERIAL READER : /dev/ttsUSB4
smartreader+
SERIAL READER : /dev/ttsUSB5
smartreader+
SERIAL READER : /dev/ttsUSB6
smartreader+
SERIAL READER : /dev/ttsUSB7
smartreader+
# Serial reader smartcard write delay.
# Setting to finetune smartcard write speed, optimal setting depends on speed of system, and
# speed of card. Default value is calculated, but can overrule by setting.
# Use number of microseconds delay between bytes, 0 = no delay, -1 = calculated default
# Note: huge difference between values 0 and 1, because of schedular overhead
#
# SMARTCARD WRITE DELAY : <device> <delay>
#
# example, 10ms write delay on smartcard in reader attached to /dev/ttyUSB0
#
#SMARTCARD WRITE DELAY: /dev/ttyUSB0 10000
#
# NOTE on sc8in1; because 8 smartcards are used on the same devicename, use
# devicename_0 .. devicename_7 for settings which require devicename to make
# settings per smartcard. example /dev/ttyS0_0, /dev/ttyS0_1 ..
# example, 8ms write delay between bytes to smartcard on last sc8in1 channel, attached to /dev/tts/0
#
#SMARTCARD WRITE DELAY: /dev/tts/0_7 8000
# Smartcard clock speed override
# Setting override specified speed for smartcard.
# Don't add setting unless you're sure what you're doing.
# In 99% of the cases the reader selects the optimal speed.
# Adding this setting either slows your card down, or might destroy it.
#
# SMARTCARD CLOCK FREQUENCY : <device> <freq>
#
# example
#
#SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 5500000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB0 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB1 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB2 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB3 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB4 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB5 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB6 6000000
SMARTCARD CLOCK FREQUENCY: /dev/ttsUSB7 6000000
# if timing should be shown in OSD and debug output
# default is no (turned off)
#
#SHOW TIMING : yes
# enables mini OSD which shows server(type), cardreader, keys or fta only
# default is no (turned off)
#
#MINI OSD : yes
# turns debugging on and off
# default is no (turned off)
#
#DEBUG : yes
# should CCcam try to read and parse newcamd.conf for server connections
# default is no (turned off)
#
#NEWCAMD CONF : yes
Das müsste do passenoder ich bin am verzweifeln