Support Audi RMC Boot Loop

[Ahmeda]

Hi Guys, I need help because I bricked RMC Audi A1. I mede something wrong with uart connection and now have boot loop every minute. I have made backup before but i dont know how to recover from this backup? Please help if any budy knows how to fix it?

 

[Nickkkkk18]

Hello,

Anyone here can help with an RMC HW4 in bootloop?

Spoiler

IPL-BOOT1-Start on DDR-Jacinto-MOST platform

IPL: RMC-PA 16bit flash configuration!!!

Please wait while the system comes up ...

Starting flash driver ...
Flash driver started
# Startup bootimage /etc/rc ...

IPL software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
Boot1 software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
Boot2 software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
EMB software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
STDB software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
Application software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
No language partition found
HOME software version: RMC_MOST_Q3-SW AP_20140804.DAB 2014/08/04 09:11:43
TSDriver: JDDR2 board detected [0x90]
++++++++++++++++++++++++++++++++++++++++++++++++++++
+ DSPLink binary info +
++++++++++++++++++++++++++++++++++++++++++++++++++++ ++

• +
• Software label = dsplink160 +
• Build date = Aug 4 2014 +
• Build time = 08:59:56 +
• Type of build = JACINTO DDR FULL +
• DSPLINK = 1.62 +
• +

++++++++++++++++++++++++++++++++++++++++++++++++++++ ++
SD_SIM: SD_Jacinto_Parse_Args ENTER
SD_SIM: SD_Sim_HBA_Pulser_Startup: devb-sd-jacinto-internal.so init card context 0
SD_SIM: [SDCARD 3] card INSERTED
SD_SIM: Card_Init: driver strength set to 8mA
SD_SIM: eMMC in SLC mode
SD_SIM: [SDCARD 3] Write repeat enabled
SD_SIM: SD_Dev_Message_Handler, card (0) ready (path 0)
procman: [pid: 135178] - Logger activated on Thu Jan 1 00:00:02 1970
Group mask = 2, debug level = 0

procman: 1-[1]-I-DT_PM-pm_main_thread.c-611-Procman started, 0, 0:00:02.328
Parsing DSP configuration file: /dsp/dsp.conf
Done parsing the config file
New Loading 3923313 bytes of RAW DSP IMAGE, loading finished.
Reset DSP Done!
Power up DSP Done!
Copy binary to ram. Clear DSP memory area: NO
Done!
Modifying reset vector Done!
Setting start address Done!
Releasing DSP from reset Done!
Connection to DSP established.

vielen dank!

 

[thor222]

Hi Guys, I need help because I bricked RMC Audi A1. I mede something wrong with uart connection and now have boot loop every minute. I have made backup before but i dont know how to recover from this backup? Please help if any budy knows how to fix it?

Do you have an RMC4 HW-H62?