Vu_duo

[bibo1]

hallo,

meine vu duo läuft nicht mehr hoch der Stick macht alles fein bis zum Ende. der Start läuft aber nicht durch, bleibt beim Starting hänge mit folgendem Hyperterminal Mitschnitt:

Spoiler

BCM73350010
012
Shmoo Version=1.9

MEMC-00000000 RW=0000000E WW=00000045 G=00000001 R=00000009 W=0000001C
MEMC-00000001 RW=0000000F WW=00000047 G=00000001 R=00000009 W=00000007 #$
3
COPY CODE
A567

BCM97335B0 CFE v2.17, CFE core v2.12, Endian Mode: Little
Build Date: Thu Sep 29 12:01:32 2011 (shcheong@ncsh)
Copyright (C) Broadcom Corporation.

writing vfd

DDR Freq: 395MHz
CPU speed: 405MHz
Memory Config: 32+16 non-UMA
Device Tech: 1Gb
Total memory: 384MB
Boot Device: NAND
ECC: Hamming
Total flash: 128MB

Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub

CFE initialized.

checking usb
Loader:elf Filesys:raw Dev:flash0.kernel File: Options:rootfstype=jffs2 root=/de
v/mtdblock0 rw mem=0x8000000 bcmrac=3
Loading: 0x80001000/6641920 0x80656900/137936 Entry address is 0x804d6470
TP1 Entry Address at 0x80000ffc = 804d6470
Starting program at 0x804d6470

Linux version 3.9.6 (plnick@build-plnick) (gcc version 4.6.4 20120303 (prereleas
e) (GCC) ) #1 SMP Mon Mar 30 19:26:57 CEST 2015
Fetching vars from bootloader... found 11 vars.
Early serial console at MMIO32 0x10400b00 (options '115200n')
bootconsole [uart0] enabled
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 pci=1 smp=1 moca=0 usb=1
Using 256 MB + 128 MB RAM (from CFE)
bootconsole [early0] enabled
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
bmem: adding 118 MB RESERVED region at 138 MB (0x07600000@0x08a00000)
Zone ranges:
Normal [mem 0x00000000-0x0fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x0fffffff]
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
PERCPU: Embedded 7 pages/cpu @81204000 s6400 r8192 d14080 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: bmem=118M ubi.mtd=0 root=ubi0:rootfs rootfstype=ubifs rw ro
otflags=sync
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
__ex_table already sorted, skipping sort
Memory: 132356k/262144k available (4989k kernel code, 129788k reserved, 1257k da
ta, 276k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Detected MIPS clock frequency: 404 MHz (202.497 MHz counter)
Calibrating delay loop... 403.45 BogoMIPS (lpj=201728)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
SMP: Booting CPU1...
CPU revision is: 0002a044 (Brcm4380)
FPU revision is: 00130001
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
SMP: CPU1 is running
Brought up 2 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
USB0: power enable is active high; overcurrent is active low
PCI2.3->SDRAM window: 512 MB
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xd0000000-0xefffffff]
pci_bus 0000:00: root bus resource [io 0x0400-0x83ff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0x10510000-0x1051ffff]
pci_bus 0000:01: root bus resource [io 0x8400-0x87ff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
PCI: found device 14e4:8602 on SATA bus, slot 0 (irq 42)
pci 0000:01:00.0: BAR 5: assigned [mem 0x10510000-0x10510fff]
pci 0000:01:00.0: BAR 6: assigned [mem 0x10511000-0x105117ff pref]
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource upg
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
msgmni has been set to 258
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x10400b00 (irq = 22) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
serial8250.0: ttyS1 at MMIO 0x10400b40 (irq = 66) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10400b80 (irq = 67) is a 16550A
loop: module loaded
PCI: Enabling device 0000:01:00.0 (0000 -> 0003)
scsi0 : sata_brcmstb
scsi1 : sata_brcmstb
ata1: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510000 irq 42
ata2: SATA max UDMA7 mmio m4096@0x10510000 port 0x10510100 irq 42
Broadcom STB NAND controller (BrcmNand Controller)
bcmemac: Broadcom STB 10/100 EMAC driver v3.0
bcmemac: registered interface #0 at 0x10080000 as 'eth0' (00:1d:ec:02:b9:03)
bcmemac: not registering interface #1 at 0x10090000 (no PHY detected)
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 62, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 3
ohci-brcm ohci-brcm.0: irq 63, io mem 0x10480400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 4
ohci-brcm ohci-brcm.1: irq 64, io mem 0x10480600
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Key type dns_resolver registered
EBI CS0: setting up NAND flash (primary)
ata1: SATA link down (SStatus 4 SControl 300)
mtd->oobsize=0, mtd->eccOobSize=0
NAND_CS_NAND_XOR=00000001
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Block size=00020000, erase shift=17
NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB on CS0

Found NAND on CS0: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=4232222d,
tim2=00000d94
BrcmNAND version = 0x0201 128MB @00000000
B4: NandSelect=40000101, nandConfig=55042200, chipSelect=0
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=55042200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 2.1 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Creating 7 MTD partitions on "brcmnand.0":
0x000000000000-0x000007600000 : "rootfs"
0x000007600000-0x000007a00000 : "kernel"
0x000007a00000-0x000007c00000 : "boot"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
PM: CP0 COUNT/COMPARE frequency depends on divisor
UBI: attaching mtd0 to ubi0
ata2: SATA link down (SStatus 4 SControl 300)
UBI: scanning is finished
UBI: attached mtd0 (name "rootfs", size 118 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 944, bad PEBs: 0, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 181
5153527
UBI: available PEBs: 0, total reserved PEBs: 944, PEBs reserved for bad PEB hand
ling: 20
ALSA device list:
UBI: background thread "ubi_bgt0d" started, PID 47
No soundcards found.
UBIFS: parse sync
UBIFS: background thread "ubifs_bgt0_0" started, PID 48
UBIFS: recovery needed
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"(null)
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/20
48 bytes
UBIFS: FS size: 115421184 bytes (110 MiB, 909 LEBs), journal size 9023488 bytes
(8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 1776E467-14E7-48DC-B7D5-59374
1C9A08A, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:10.
devtmpfs: mounted
Freeing unused kernel memory: 276k freed
INIT: version 2.88 booting
procmk_init
dvb_bcm7335: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (bm750)
bcm7335: hotplug_callback():
Hotplug - status.connected 1
bcm7335: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
CPU 0 Unable to handle kernel paging request at virtual address e0717100, epc ==
e0717100, ra == 80076464
Oops[#1]:
Cpu 0
$ 0 : 00000000 10008300 e0717100 00060000
$ 4 : 0000000b e0b82904 00000000 000000fb
$ 8 : 10008700 1000001f 0000000b fffffff4
$12 : 806198c8 0000000a ffffffff 004c0000
$16 : 86dfd900 0000000b 00000000 00000000
$20 : 0000000b 805d8dc0 805e0000 80620000
$24 : 004b8514 77f0be2c
$28 : 87c0a000 87c0bb98 80573288 80076464
Hi : 00000000
Lo : 00000000
epc : e0717100 0xe0717100
Tainted: P O
ra : 80076464 handle_irq_event_percpu+0x78/0x288
Status: 10008302 KERNEL EXL
Cause : 00800008
BadVA : e0717100
PrId : 0002a044 (Brcm4380)
Modules linked in: procmk(O)
Process modprobe (pid: 69, threadinfo=87c0a000, task=885ba0f8, tls=77fc5490)
Stack : 3b9aca00 00000000 805d8644 00000100 805d8640 0000000a 00000000 00000000
805d8dc0 0000000b 00000001 00000020 00001400 fffff7ff ffffffbf 87c0be6
0
81111940 800766c4 00000001 00000004 00000000 00000002 00000003 0000000
1
805d8dc0 80079f30 887b27e4 00000000 0000000b 00000001 00000000 80075a7
c
00000068 00000000 00000002 80002ac8 00000000 800077b4 00000000 0000000
1
...
Call Trace:
[<800766c4>] handle_irq_event+0x50/0x8c
[<80079f30>] handle_level_irq+0xd4/0x14c
[<80075a7c>] generic_handle_irq+0x3c/0x5c
[<80002ac8>] plat_irq_dispatch+0xa8/0x104
[<800077b4>] do_IRQ+0x18/0x24
[<80002890>] brcm_intc_dispatch.isra.0+0x90/0x220
[<80005a44>] ret_from_irq+0x0/0x4
[<80079f38>] handle_level_irq+0xdc/0x14c
[<80002ae8>] plat_irq_dispatch+0xc8/0x104
[<80005a44>] ret_from_irq+0x0/0x4
[<804e0000>] __kprobes_text_end+0xf78/0x1400
[<800b4080>] page_remove_rmap+0xd4/0xdc
[<8009f8bc>] __dec_zone_state+0x84/0x18c
[<800b4080>] page_remove_rmap+0xd4/0xdc
[<800a6824>] __tlb_remove_page+0xb0/0xe8
[<800a8a08>] unmap_single_vma+0x4f0/0x768
[<8005281c>] __wake_up+0x40/0x60
[<800a98b0>] unmap_vmas+0x68/0x90
[<800930d4>] lru_add_drain+0x10/0x1c
[<800adf08>] unmap_region+0x84/0xf0
[<800afff0>] do_munmap+0x270/0x3c0
[<804de844>] __down_write_nested+0xcc/0xe8
[<800b0180>] vm_munmap+0x40/0x68
[<8000e13c>] stack_done+0x20/0x40
[<802436d8>] __bzero+0xbc/0x164


Code: (Bad address in epc)

---[ end trace b4b20a36ab4aaa9b ]---
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 180 seconds..

kann jemand etwas dzu sagen und mir vielleicht helfen?

Gesagt sei noch, dass ich die Box mittels CY7C...mini board und BBS (rote Led) wieder zurück ins Leben zurück geholt habe ( jedoch nicht so ganz).

Grüsse
bibo1