Hallo.
Ich nutze Neutrino auf meiner UFS 910 Box.(Sh4)
Als Gbox Version nutze ich die 8.06 Git mit Smargo Support.
Der Smargoreader ist von Argolis und die Einstellungen stehen auf Auto.
Ich habe das Problem (speziell bei Hd+,seltener auch bei Sky) das der Ton häufiger stockt. Manchmal auch das Bild. Ich vermute das es an Emms liegt.
Aufhänger der Box sind auch schon ein paar Mal passiert. Man kann dann nicht mehr zappen und der letzte Kanal bleibt im Display stehen.
Ausschliessen wollte ich mal die Configdatei von Gbox.
Der Emu soll als Programm für die Skykarte und als eigentlicher Emu benutzt werden.
Funktionieren tut das zwar (so einigermaßen) mit der Config aber könnte bitte jemand mal drüber schauen ?
Für Hilfe wäre ich Dankbar.
Gruss
Breeza
Ich nutze Neutrino auf meiner UFS 910 Box.(Sh4)
Als Gbox Version nutze ich die 8.06 Git mit Smargo Support.
Der Smargoreader ist von Argolis und die Einstellungen stehen auf Auto.
Ich habe das Problem (speziell bei Hd+,seltener auch bei Sky) das der Ton häufiger stockt. Manchmal auch das Bild. Ich vermute das es an Emms liegt.
Aufhänger der Box sind auch schon ein paar Mal passiert. Man kann dann nicht mehr zappen und der letzte Kanal bleibt im Display stehen.
Ausschliessen wollte ich mal die Configdatei von Gbox.
Der Emu soll als Programm für die Skykarte und als eigentlicher Emu benutzt werden.
Funktionieren tut das zwar (so einigermaßen) mit der Config aber könnte bitte jemand mal drüber schauen ?
Für Hilfe wäre ich Dankbar.
# gbox config file
# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 00 00 }
# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }
# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
# 1X show ca access
# 2X use nagra aladin 1801 in betacrypt mode (for UM-I02)
C: { 00 }
# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 00 }
# Auto Update
# 00 is ignored (default)
# 01 enable AU
# 02 Auto AU !!!!! always use this !!!!!
# 03 enable AU with ua,sa and ga filter !!!!! always use this !!!!! (not working on coolstream)
A: { 03 }
# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }
# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }
# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 }
# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 }
# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
#(in the dbox2 the gbox writes directly the CWs, 00 is the
#recommended mode ! No drivers are required) use D* ** ONLY if
# you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x* invert CTS detection on com2
V: { 00 05 } // smargo
#V: { F0 30 } // sci0 und sci1
#V: { 00 35 } // sci0 und sci1 und smargo
# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
R: { 00 }
# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
W: { 00 00 } 9600
# ================================================== ===========================
# extra options to override default seting in case you expirience Problems,
# normaly these setings are not required.
# GboxTwin mode
# this options for the 2nd gbox ONLY
# you must have an extra gbox, gbox_cfg and cwshare.cfg running on /tmp,
# all other files can linked to the org. files
#F: { A6 } 5
# cpu, api, cw write method
# 00 auto
# 01 80X86
# 02 MPC823
# 03 IBM STB04xxx
# 00 auto
# 01 ibm
# 02 api2
# 03 api3
# 00 cw write st<x>yle= use internal routine (only dbox2)
# 01 cw write st<x>yle= CA_SET_DESCR type1 (dbox2, vdr)
# 02 cw write st<x>yle= CA_SET_DESCR type2
# 03 cw write st<x>yle= CA_SET_DESCR type3
# 04 cw write st<x>yle= 16 byte /proc/bus/gtx
# 05 cw write st<x>yle= 4096 byte /proc/bus/gtx, cw offset=0x04D0
# xx write cw in 1st device with index=xx
# yy write cw in 2nd device with index=yy
# 01 means with .index=0 (default)
# 02 means with .index=1
# 03 means with .index=0 and .index=1
# .. any bitwise combination ...
# FF means with all 8 indexes (0-7)
#J: { 00 00 02 00 00 }
# Files, folders, devices
# folder/device comment
#F: { 01 } /var/tmp/pmt.gbx // pmt file
#F: { 02 } /var/tmp/emm.info // key update log file
#F: { 03 } /var/tmp/ecm.info // ecm info file
#F: { 04 } /var/tmp/atack.txt // atack info file
#F: { 08 } 1 // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
F: { 11 } /var/keys // folder for config files
#F: { 12 } /var/tmp // folder for temporary file
F: { 13 } /var/keys // folder for keyfiles
#F: { 21 } /dev/null // ca device
#F: { 22 } /dev/null // dvr device
#F: { 23 } /dev/null // demux device
#F: { 31 } /dev/null // second ca device to write cw's (recording)
#F: { 41 } /dev/sci0 // STB04xxx slot1
#F: { 42 } /dev/sci1 // STB04xxx slot1
F: { 43 } /dev/ttyUSB0 // rs232 com1
#F: { 44 } /dev/ttyUSB1 // rs232 com2
########### change for IRD firmware ################
#F: { 01 } /tmp/pmt2_1.tmp
#F: { 02 } /tmp/emm.info
#F: { 03 } /tmp/ecm.info
#F: { 04 } /tmp/atack.txt
#F: { 12 } /tmp
#F: { 21 } PTI1
#F: { 22 } PTI1
#F: { 23 } PTI1
################################################## #########
# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 02 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
F: { 58 } 03 // nds
# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1
# set stay alive ping time in seconds (default is 300)
F: { A0 } 300
# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
#F: { A1 } 0
# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 00 00 }
# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }
# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
# 1X show ca access
# 2X use nagra aladin 1801 in betacrypt mode (for UM-I02)
C: { 00 }
# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 00 }
# Auto Update
# 00 is ignored (default)
# 01 enable AU
# 02 Auto AU !!!!! always use this !!!!!
# 03 enable AU with ua,sa and ga filter !!!!! always use this !!!!! (not working on coolstream)
A: { 03 }
# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }
# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }
# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 }
# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 }
# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
#(in the dbox2 the gbox writes directly the CWs, 00 is the
#recommended mode ! No drivers are required) use D* ** ONLY if
# you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x* invert CTS detection on com2
V: { 00 05 } // smargo
#V: { F0 30 } // sci0 und sci1
#V: { 00 35 } // sci0 und sci1 und smargo
# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
R: { 00 }
# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
W: { 00 00 } 9600
# ================================================== ===========================
# extra options to override default seting in case you expirience Problems,
# normaly these setings are not required.
# GboxTwin mode
# this options for the 2nd gbox ONLY
# you must have an extra gbox, gbox_cfg and cwshare.cfg running on /tmp,
# all other files can linked to the org. files
#F: { A6 } 5
# cpu, api, cw write method
# 00 auto
# 01 80X86
# 02 MPC823
# 03 IBM STB04xxx
# 00 auto
# 01 ibm
# 02 api2
# 03 api3
# 00 cw write st<x>yle= use internal routine (only dbox2)
# 01 cw write st<x>yle= CA_SET_DESCR type1 (dbox2, vdr)
# 02 cw write st<x>yle= CA_SET_DESCR type2
# 03 cw write st<x>yle= CA_SET_DESCR type3
# 04 cw write st<x>yle= 16 byte /proc/bus/gtx
# 05 cw write st<x>yle= 4096 byte /proc/bus/gtx, cw offset=0x04D0
# xx write cw in 1st device with index=xx
# yy write cw in 2nd device with index=yy
# 01 means with .index=0 (default)
# 02 means with .index=1
# 03 means with .index=0 and .index=1
# .. any bitwise combination ...
# FF means with all 8 indexes (0-7)
#J: { 00 00 02 00 00 }
# Files, folders, devices
# folder/device comment
#F: { 01 } /var/tmp/pmt.gbx // pmt file
#F: { 02 } /var/tmp/emm.info // key update log file
#F: { 03 } /var/tmp/ecm.info // ecm info file
#F: { 04 } /var/tmp/atack.txt // atack info file
#F: { 08 } 1 // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
F: { 11 } /var/keys // folder for config files
#F: { 12 } /var/tmp // folder for temporary file
F: { 13 } /var/keys // folder for keyfiles
#F: { 21 } /dev/null // ca device
#F: { 22 } /dev/null // dvr device
#F: { 23 } /dev/null // demux device
#F: { 31 } /dev/null // second ca device to write cw's (recording)
#F: { 41 } /dev/sci0 // STB04xxx slot1
#F: { 42 } /dev/sci1 // STB04xxx slot1
F: { 43 } /dev/ttyUSB0 // rs232 com1
#F: { 44 } /dev/ttyUSB1 // rs232 com2
########### change for IRD firmware ################
#F: { 01 } /tmp/pmt2_1.tmp
#F: { 02 } /tmp/emm.info
#F: { 03 } /tmp/ecm.info
#F: { 04 } /tmp/atack.txt
#F: { 12 } /tmp
#F: { 21 } PTI1
#F: { 22 } PTI1
#F: { 23 } PTI1
################################################## #########
# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 02 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
F: { 58 } 03 // nds
# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1
# set stay alive ping time in seconds (default is 300)
F: { A0 } 300
# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
#F: { A1 } 0
Gruss
Breeza
