Code:
# CAS settings (NEW)
#
#[generic]
#reset_rs232_buffer = 0 ; (default: 1) empty RS232 buffer before writing
#
#[slot-n] ; slot section with n=1..18
#include = /foo/slot.cfg ; looking for section parameters in user defined configuration file, only outside of a section defined parameters will be used
#initialization = basic ; (default: basic) [basic,extended] init card in basic or extended mode
#disable_pts = 0 ; (default: 0) enable/disable protocol type selection (PTS) handshake
#enable_ice = 0 ; (default: 0) enable (ICE-IRD)/disable (ICE-CRW) irdeto cryptoworks enveloped support
#enable_onionmode = 0 ; (default: 0) enable/disable irdeto/nagra aladin onion mode (1833(1702)1833)
#alternative_frequency = 0 ; (default: 0) check additional osc frequency, value in kHz, example 8MHz=8000000
#alternative_baudrate = 0 ; (default: 0) check additional baudrate for atr, value in bit/s, example 81861
#byte_delay = 0 ; (default: 0) unit (1e-6 s)
#instruction_delay = 0 ; (default: 0) unit (1e-3 s)
#cwcrcmode = 0 ; (default: 1) 0 - disable, 1 - crc mode 1
#nuid = <4 byte> ; STB chipset nuid - (ex. A1A2A3A4)
#cwpk = [0-7]:<16 byte key data> ; STB chipset cwpk data - (ex. 0:E0E1E2E3E4E5E6E7E8E9EAEBECEDEEEF)
#camid = <4 byte>
#camctrl = <4 byte>
#camnonce = <4 byte>
#
#nagra-pk-3310 = <16 byte>
#nagra-pk-3460 = <96 byte>
#nagra-pk-3588 = <136 byte>
#nagra-merlin-gmod = <112 byte>
#nagra-merlin-gsig = <112 byte>
#
#enable_unique_emm = 1 ; (default: 0) set unique emm section filter on demux device
#enable_shared_emm = 1 ; (default: 0) set shared emm section filter on demux device
#enable_global_emm = 1 ; (default: 0) set global emm section filter on demux device
#block_unique_emm = 0 ; (default: 1) block unique address/hex_serial emm
#block_shared_emm = 0 ; (default: 1) block shared address/provider emm
#block_global_emm = 0 ; (default: 1) block global address/all_card emm
#block_user_emm = 0 ; (default: 1) block user emm, read from /var/tmp/remm.txt
#save_processed_emm = 1 ; (default: 0) save processed EMMs to (/var/tmp/scXX.emmproc)
#save_processed_emm_file = /var/keys/sc0X.emmproc; (default: /var/tmp/scXX.emmproc) user defined output file
#save_rejected_emm = 1 ; (default: 0) save rejected EMMs to (/var/tmp/scXX.emmblock)
#save_rejected_emm_file = /var/keys/sc0X.emmblock; (default: /var/tmp/scXX.emmblock) user defined output file
#
#sidfilter = 000C,000D ; define sids can dispatch or not dispatch by card
#sidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line local rule 00
# ; allow_all - old cwshare S-Line local rule 01
# ; allow_defined - old cwshare S-Line local rule 02
# ; deny_defined - old cwshare S-Line local rule 03
#sidfilter_global_policy = allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line global rule 00
# ; allow_all - old cwshare S-Line global rule 01
# ; allow_defined - old cwshare S-Line global rule 02
# ; deny_defined - old cwshare S-Line global rule 03
#sidfilter_teacher = card ; [card,network] use selected ecm request source to update sidfilter (add or delete current sid)
# ; card - old cwshare S-Line global rule 03, means allow defined and update by zone0
# ; network - old cwshare S-Line global rule 03, means allow defined and update by zone1
#
#pidfilter = 100C,100D ; define pids can dispatch or not dispatch by card
#pidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#pidfilter_global_policy = allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#
########################################################################################
Zuletzt bearbeitet von einem Moderator:
