gbox.net.git811.K.public1

[Schicki]

hat jemand noch eine Gbox Oscam kombi für die Solo2 ?

 

[saki11]

Hallo,
wie kann ich eine Sky UM02 Karte mit Gbox aktivieren da ich noch keinen
original Receiver bekommen habe.
Muss ich noch was in Gbox Dateien ändern
ich habe es versucht aber es wird nicht hell.

Mit einer Dreambox 900UHD

Danke

 

[saki11]

Kann keiner weiter helfen.

 

[DarkStarXxX]

Warum nicht einfach für die UM02 OSCam nehmen?

 

[sodex]

debug.txt ? => im "temp" Ordner zu finden
sci01.info oder sci02.info ? => im "temp" Ordner zu finden
gbox.cfg und softcam.cfg ? => im Ordner "usr/keys"
vielleicht kann dann jemand was zu sagen
MfG sodex

 

[saki11]

ja das alles ist schon drin aber es wird nicht hell.

 

[d2z]

Du sollst den Inhalt hier posten meinte er damit.

 

[sodex]

ich vermute mal, da die Box nur einen Kartenleser hat und die Blocker auf ein gestellt sind die Karte nicht mit emm's versorgt wird
MfG sodex

 

[saki11]

Bei mir ist im tmp ordner nur debug.txt drin keine sci01.info oder die sci02.info

Spoiler: softcam.cfg

# CAS settings (NEW)
#
#[generic]
#reset_rs232_buffer = 1 ; (default: 1) empty RS232 buffer before writing
#
#[slot-n] ; slot section with n=1..18
#include = /foo/slot.cfg ; looking for section parameters in user defined configuration file, only outside of a section defined parameters will be used
#initialization = basic ; (default: basic) [basic,extended] init card in basic or extended mode
#disable_pts = 0 ; (default: 0) enable/disable protocol type selection (PTS) handshake
#enable_ice = 0 ; (default: 0) enable/disable irdeto cryptoworks enveloped support
#enable_onionmode = 0 ; (default: 0) enable/disable irdeto/nagra aladin onion mode (1833(1702)1833)
#alternative_frequency = 0 ; (default: 0) check additional osc frequency, value in kHz, example 8MHz=8000000
#alternative_baudrate = 0 ; (default: 0) check additional baudrate for atr, value in bit/s, example 81861
#byte_delay = 0 ; (default: 0) unit (1e-6 s)
#instruction_delay = 0 ; (default: 0) unit (1e-3 s)
#
#enable_unique_emm = 0 ; (default: 0) set unique emm section filter on demux device
#enable_shared_emm = 0 ; (default: 0) set shared emm section filter on demux device
#enable_global_emm = 0 ; (default: 0) set global emm section filter on demux device
#block_unique_emm = 1 ; (default: 1) block unique address/hex_serial emm
#block_shared_emm = 1 ; (default: 1) block shared address/provider emm
#block_global_emm = 1 ; (default: 1) block global address/all_card emm
#block_user_emm = 1 ; (default: 1) block user emm, read from /var/tmp/remm.txt
#save_processed_emm = 0 ; (default: 0) save processed EMMs to (/var/tmp/scXX.emmproc)
#save_processed_emm_file= /var/keys/sc0X.emmproc; (default: /var/tmp/scXX.emmproc) user defined output file
#save_rejected_emm = 0 ; (default: 0) save rejected EMMs to (/var/tmp/scXX.emmblock)
#save_rejected_emm_file = /var/keys/sc0X.emmblock; (default: /var/tmp/scXX.emmblock) user defined output file
#
#sidfilter = 000C,000D ; define sids can dispatch or not dispatch by card
#sidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line local rule 00
# ; allow_all - old cwshare S-Line local rule 01
# ; allow_defined - old cwshare S-Line local rule 02
# ; deny_defined - old cwshare S-Line local rule 03
#sidfilter_global_policy= allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line global rule 00
# ; allow_all - old cwshare S-Line global rule 01
# ; allow_defined - old cwshare S-Line global rule 02
# ; deny_defined - old cwshare S-Line global rule 03
#sidfilter_teacher = card ; [card,network] use selected ecm request source to update sidfilter (add or delete current sid)
# ; card - old cwshare S-Line global rule 03, means allow defined and update by zone0
# ; network - old cwshare S-Line global rule 03, means allow defined and update by zone1
#
#pidfilter = 100C,100D ; define pids can dispatch or not dispatch by card
#pidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#pidfilter_global_policy= allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#
########################################################################################
#V13/14 Karten
#Sobald für die Karte eine Verlängerung gesendet wird erstellt die gbox in/tmp eine Datei
#Namens SC01.emmblock.Den dort enthaltenen Verlängerer kopiert ihr dann in eine Datei Namens remm.txt
#und schiebt diese dann nach /tmp die gbox arbeitet diese Datei dann automatisch ab,
#und verlängert dann die Karte.Ihr könnt die V13/14 karte natürlich auch in einen anderen Slot stecken ,
#ihr müßt dann aber die config genauso anlegen wie die für Slot 1.
#Solltet ihr noch mehr Karten haben und ein/en externe/n Reader/s benutzen dann müßt ihr die Slots erweitern.
#Ihr könnt bis zu 18 Slots erstellen. Slot1 und Slot2 sind immer eure internen Reader der Box ,ab Slot3 beginen dann
#eure externen Reader.

[generic]
reset_rs232_buffer = 1

[slot-2] # Exklusiv für V13/14 Karten
initialization = extended
disable_pts = 0
enable_ice = 0 # ORF Karte 0=cryptoworks/Mode 1=irdeto/Mode
alternative_frequency = 0
alternative_baudrate = 0
byte_delay = 0
instruction_delay = 0
#
enable_unique_emm = 1
enable_shared_emm = 1
enable_global_emm = 0
block_unique_emm = 1
block_shared_emm = 1
block_global_emm = 1
block_user_emm = 0
save_processed_emm = 1
save_rejected_emm = 1

[slot-1] # Karten die nicht geblock werden brauchen
initialization = extended
disable_pts = 0
enable_ice = 0 # # ORF Karte 0=cryptoworks/Mode 1=irdeto/Mode
alternative_frequency = 0
alternative_baudrate = 0
#
enable_unique_emm = 1
enable_shared_emm = 1
enable_global_emm = 1
block_unique_emm = 0
block_shared_emm = 0
block_global_emm = 0
block_user_emm = 0
save_processed_emm = 0
save_rejected_emm = 0

Spoiler: gbox.cfg

# gbox config file

# Trace, Debug
# xx yz ; xx=00 no konsole output
# xx yz ; xx=01 konsole output
# xx yz ; y=0 debug output (dont use)
# xx yz ; y=1 no debug output
# xx yz ; z=0 ouput to konsole
# xx yz ; z=1 output to /var/tmp/debug.txt
# xx yz ; z=2 Output to UDP (to capture with gboxt)
Z: { 01 01 } 192.168.0.12 8024

# gbox working mode
# 00 pure Emu
# 01 pure SoftCam (when card inside), Emu (when no card inside)
# 02 pure Net Client
# 03 Mixed mode !!!!! always use this !!!!!
G: { 03 }

# Display ECM messages on Konsole
# 00 dont show any ECMs
# 01 show only valid ECMs
# 02 show valid and bad ECMs with complete data display
C: { 01 }

# Display EMM messages on Konsole
# 00 dont show any EMMs
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
# 1* Log any tier change on PW-Nagra-17xx cards into /var/keys/pwupdate.log
M: { 01 }

# Auto Update
# 00 AU disable (default)
# 01 AU enable
# 02 AU auto
# 03 AU enable with ua,sa and ga filter !!!!! always use this !!!!!
A: { 03 }

# Key Update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }

# Hash pids
# 00 hash all pids, DO NOT USE THIS OPTION, IT IS ONLY FOR TESTING STUFF
# 01 hash only pids with implemented algos and available keys !!!!! always use this
H: { 01 }

# Key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# On Screen Display for the Multysystemcam on com1/com2
# 00 No OSD (default)
# 01 display Smartcard messages in Neutrino
# 02 display Smartcard messages in Neutrino new nhttpd format
# 03 display Smartcard messages in Enigma
# 04 display Smartcard messages in Enigma2
O: { 00 } 192.168.0.12 dm900

# Logger and NET-mode UDP port Init
# 00 do not init UDP port
# 01 Init UDP port for IP, port, UDP
L: { 00 } 192.168.0.12 dm900

# demux, multicam/comport configuration
# example: yz = 0x0A = 00001010 (use com2 with inverted CTS detection line)
# *x ** ; x = device nummber to be used (0= default)
# D* ** ; force use of /proc/bus/gtx for cw write operations
# (in the dbox2 the gbox writes directly the CWs, 00 is the
# recommended mode ! No drivers are required) use D* ** ONLY if
# you have Problems. 0* ** should be prefered !!!
# F* ** ; write CWs in both devices (used for PVR in STB04xxx devices)
# ** y* ; y=0001b (0x1*) use slot1 as Multicam (only on STB04xxx)
# ** y* ; y=0010b (0x2*) use slot2 as Multicam (only on STB04xxx)
# ** y* ; y=0011b (0x3*) use slot1 and slot2 as Multicams (only on STB04xxx)
# ** *z ; z=0001b (0x*1) use com1 as Multicam
# ** *z ; z=0010b (0x*2) use com2 as Multicam
# ** *z ; z=0011b (0x*3) use com1 and com2 as Multicams
# ** yz ; yz=00110011b (0x33) use slot1+slot2+com1+com2 as Multicams
# ** *z ; z=0100b (0x*4) invert CTS detection on com1
# ** *z ; z=1000b (0x*8) invert CTS detection on com2
V: { 00 10 } #Slot 1
#V: { 00 20 } #Slot 2
#V: { 00 30 } #Slot 1+2
#V: { 00 3F } #Slot 1+2+SC8in1

# RS232 SSSP mode
# x debug messages, 1=on, 0=off
# y com port to use (0=none, 1=com1, 2=com2)
#R: { 00 } 9600

# Task type
# 00 ** normal mode gbox mode (no season, use Multicam instead)
# 01 ** Season Emulation in a Irdeto allcam chid 0602 nonZ
# 10 ** Season Emulation in a Irdeto allcam chid 1702 nonZ
# 11 ** Season Emulation in a Irdeto allcam chid 1702 Z
# 12 ** Season Emulation in a Irdeto allcam chid 1722 Z
# 13 ** Season Emulation in a Irdeto allcam chid 1762 Z
# ** *1 Com port to use for season emulatiom (1 or 2)
# ** 0* Use CTS for RST detection
# ** 1* Use DCD for RST detection
# ** ** 9600 = Baudrate to be used (working only on dbox2)
#W: { 00 00 } 9600
W: { 00 00 }

# =============================================================================
# extra options to override default setting in case you expirience Problems,
# normaly these setings are not required.

# Files, folders, devices
# folder/device comment
F: { 01 } /tmp/pmt.tmp // pmt file
F: { 02 } /tmp/emm.info // key update log file
F: { 03 } /tmp/ecm.info // ecm info file
F: { 04 } /tmp/atack.txt // atack info file
F: { 08 } 1 // pmt mode (0 - pmt file mode, 1 - pmt socket mode)
F: { 11 } /var/keys // folder for config files
F: { 12 } /tmp // folder for temporary file
#F: { 13 } /var/tmp // folder for keyfiles
F: { 21 } /dev/dvb/adapter0/ca0 // ca device
F: { 22 } /dev/dvb/adapter0/dvr0 // dvr device
F: { 23 } /dev/dvb/adapter0/demux0 // demux device
#F: { 31 } /dev/null // second ca device to write cw's (recording)
F: { 41 } /dev/sci0 // STB04xxx slot1
#F: { 42 } /dev/sci1 // STB04xxx slot1
#F: { 43 } /dev/tts/0 // rs232 com1
#F: { 44 } /dev/tts/1 // rs232 com2
#F: { 43 } /dev/ttyUSB0 // rs232 com1# f?r externen Cardreader an com1 SC8in1 oder MCR 4/8 oder Smargo
#F: { 44 } /dev/ttyUSB1 // rs232 com2# f?r externen Cardreader an com2 SC8in1 oder MCR 4/8 oder Smargo

# For overclocking freaks, Clocking internal STB04xxx slots with:
# 1=7.80MHz 2=6.30MHz 3=5.25MHz 4=4.50MHz 5=3.94MHz 6=3.50MHz 7=3.15MHz
# Irdeto works fine on 7.8MHz, all other fine on 6.30MHz or 5.25MHz
# The Dream has not a clean clock signal, some cards that are sensitive will
# refuse to work even on 3.5MHz, thats why 3.15MHz is the default value there.
# On other STB04xxx recievers the same cards work with 6.30MHz
# Ist nicht Aktiv geschaltet ,also keine Funktion
#F: { 51 } 02 // irdeto
#F: { 52 } 03 // seca
#F: { 53 } 03 // viaccess
#F: { 54 } 03 // nagra
#F: { 55 } 03 // crypto
#F: { 57 } 03 // conax
#F: { 58 } 03 // nds

# force a name change of the season or sssp rs232 device
#F: { 45 } /dev/ttyS1

# set stay alive ping time in seconds (default is 300)
#F: { A0 } 300

# disable direct serial port I/O access on 80x86cpus (win and linux)
# direct port i/o is used to set unusual Baudrates, if you want to
# a 3.579MHz card in a 6.000MHz reader etc ...
#
# Enabled (A1=0) is the default setting, has always been !!!
#
# Disable (set to 1) it ONLY if you have problems with ioperm or you want
# to use a usb-to-rs232 smartcard reader
#F: { A1 } 1

# descrambler selection by camd.socket private descriptor (0 - index mode, 1 - mask mode), mask mode is default
F: { AA } 1

 

[Tweety_2000]

Wenn keine sci01 oder 02 erstellt wird ist es komisch.
Poste mal den Debug

 

[sodex]

Bei mir ist im tmp ordner nur debug.txt drin keine sci01.info oder die sci02.info

Spoiler: softcam.cfg

# CAS settings (NEW)
#
#[generic]
#reset_rs232_buffer = 1 ; (default: 1) empty RS232 buffer before writing
#
#[slot-n] ; slot section with n=1..18
#include = /foo/slot.cfg ; looking for section parameters in user defined configuration file, only outside of a section defined parameters will be used
#initialization = basic ; (default: basic) [basic,extended] init card in basic or extended mode
#disable_pts = 0 ; (default: 0) enable/disable protocol type selection (PTS) handshake
#enable_ice = 0 ; (default: 0) enable/disable irdeto cryptoworks enveloped support
#enable_onionmode = 0 ; (default: 0) enable/disable irdeto/nagra aladin onion mode (1833(1702)1833)
#alternative_frequency = 0 ; (default: 0) check additional osc frequency, value in kHz, example 8MHz=8000000
#alternative_baudrate = 0 ; (default: 0) check additional baudrate for atr, value in bit/s, example 81861
#byte_delay = 0 ; (default: 0) unit (1e-6 s)
#instruction_delay = 0 ; (default: 0) unit (1e-3 s)
#
#enable_unique_emm = 0 ; (default: 0) set unique emm section filter on demux device
#enable_shared_emm = 0 ; (default: 0) set shared emm section filter on demux device
#enable_global_emm = 0 ; (default: 0) set global emm section filter on demux device
#block_unique_emm = 1 ; (default: 1) block unique address/hex_serial emm
#block_shared_emm = 1 ; (default: 1) block shared address/provider emm
#block_global_emm = 1 ; (default: 1) block global address/all_card emm
#block_user_emm = 1 ; (default: 1) block user emm, read from /var/tmp/remm.txt
#save_processed_emm = 0 ; (default: 0) save processed EMMs to (/var/tmp/scXX.emmproc)
#save_processed_emm_file= /var/keys/sc0X.emmproc; (default: /var/tmp/scXX.emmproc) user defined output file
#save_rejected_emm = 0 ; (default: 0) save rejected EMMs to (/var/tmp/scXX.emmblock)
#save_rejected_emm_file = /var/keys/sc0X.emmblock; (default: /var/tmp/scXX.emmblock) user defined output file
#
#sidfilter = 000C,000D ; define sids can dispatch or not dispatch by card
#sidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line local rule 00
# ; allow_all - old cwshare S-Line local rule 01
# ; allow_defined - old cwshare S-Line local rule 02
# ; deny_defined - old cwshare S-Line local rule 03
#sidfilter_global_policy= allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
# ; deny_all - old cwshare S-Line global rule 00
# ; allow_all - old cwshare S-Line global rule 01
# ; allow_defined - old cwshare S-Line global rule 02
# ; deny_defined - old cwshare S-Line global rule 03
#sidfilter_teacher = card ; [card,network] use selected ecm request source to update sidfilter (add or delete current sid)
# ; card - old cwshare S-Line global rule 03, means allow defined and update by zone0
# ; network - old cwshare S-Line global rule 03, means allow defined and update by zone1
#
#pidfilter = 100C,100D ; define pids can dispatch or not dispatch by card
#pidfilter_local_policy = allow_all ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#pidfilter_global_policy= allow_defined ; (default: allow_all) [deny_all,allow_all,allow_defined,deny_defined]
#
########################################################################################
#V13/14 Karten
#Sobald für die Karte eine Verlängerung gesendet wird erstellt die gbox in/tmp eine Datei
#Namens SC01.emmblock.Den dort enthaltenen Verlängerer kopiert ihr dann in eine Datei Namens remm.txt
#und schiebt diese dann nach /tmp die gbox arbeitet diese Datei dann automatisch ab,
#und verlängert dann die Karte.Ihr könnt die V13/14 karte natürlich auch in einen anderen Slot stecken ,
#ihr müßt dann aber die config genauso anlegen wie die für Slot 1.
#Solltet ihr noch mehr Karten haben und ein/en externe/n Reader/s benutzen dann müßt ihr die Slots erweitern.
#Ihr könnt bis zu 18 Slots erstellen. Slot1 und Slot2 sind immer eure internen Reader der Box ,ab Slot3 beginen dann
#eure externen Reader.

[generic]
reset_rs232_buffer = 1

[slot-2] # Exklusiv für V13/14 Karten
initialization = extended
disable_pts = 0
enable_ice = 0 # ORF Karte 0=cryptoworks/Mode 1=irdeto/Mode
alternative_frequency = 0
alternative_baudrate = 0
byte_delay = 0
instruction_delay = 0
#
enable_unique_emm = 1
enable_shared_emm = 1
enable_global_emm = 0
block_unique_emm = 1
block_shared_emm = 1
block_global_emm = 1
block_user_emm = 0
save_processed_emm = 1
save_rejected_emm = 1

[slot-1] # Karten die nicht geblock werden brauchen
initialization = extended
disable_pts = 0
enable_ice = 0 # # ORF Karte 0=cryptoworks/Mode 1=irdeto/Mode
alternative_frequency = 0
alternative_baudrate = 0
#
enable_unique_emm = 1
enable_shared_emm = 1
enable_global_emm = 1
block_unique_emm = 0
block_shared_emm = 0
block_global_emm = 0
block_user_emm = 0
save_processed_emm = 0
save_rejected_emm = 0

wer hat denn da die Slot's verdreht Slot 2 kommt unter Slot1 - nicht das es eventuell daran liegt - weil die

Sie müssen registriert sein, um Links zu sehen.

nur einen hat - lösch das rot markierte mal raus und schau ob es dann funktioniert
MfG sodex

 

[mybuntu]

Hallo, ist es möglich Gbox so an zu passen das es mit andere cak7 provider läuft? Dazu müsste Mod1 mod2 usw angepasst werden.. Quellcode würde hilfreich... Evt PN?

 

[Tweety_2000]

Die Source wird keiner erhalten....
Kannst dir sparen diese Frage

 

[Woopser]

Hallo,

Mal eine generelle Frage. Kann Oscam au machen oder emm an gbox senden. Habe die hd04 in meiner Ultimo4k zu hause in der kabelbox und im garten eine alte dreambox aber sat.

Geht das ?

 

[sodex]

nein das geht nicht