PS3 Downgrade für FW 3.70 [NAND+NOR]

[carhatt]

Der spanische Hacker dospiedras1973 hat eine Methode zum downgraden der 256MB PS3 Konsolen von FW 3.6x released, an der er seit 2 Monaten arbeitet.

Für diese Methode wird ein Infectus Modchip benötigt und sie ist natürlich kein Kinderspiel.


Außerdem fixt es den "Waninkoko Brick" den einige Leute hatten.


Download der benötigten Dateien:

http://www.multiupload.com/V2154YEX8M

Hello, I’ve been working on this project about two months nowsince I’ve gotten to work as public so that everyone can use,this tutorial is for consoles with 256MB NAND flash does not mean it does not work in 16MB in itself is changed almostthe same in those with normal flash, but because even I havemy fat fucking 16mb 80GB I have not been able to neither prove nor verified.

Nougat (the phrase I owe to some forero around here that I really liked the expression):

With INFECTUS flash0.bin and we get our nand flash1.bin asin the tutorial to repair bad lukin nands do the same process until we get our dump flashfinal.bin 256MB

nand we open this with a simple hex editor and look for this part editor

“00 00 00 00 00 00 00 00 00 00 00 00 00 6F FF E0”

ay you will see that just under a very similar line, I find this datain the offset 000C0020 may vary according to the nand andthe party starts here:-D

EVEN replace that line with the file if you use the hxd1patchcos.bin get in the first 0 of the line -> right click and paste writing before you have to have an open 1patchcos.binhxd in hex ​​and copy its contents to can paste .[ps3hax.net]

“00 00 00 00 00 00 10 10 00 00 00 00 00 00 10 10 00 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 40″

and in the same way as the first patched patched this alsocojemos 2patchtrvk.bin pack the file and replace the entire contents including the “00 00 00 00 00 00 10 10 00 00 00 00 00 00 10 10 00 00 00 00 00 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 02 40”

then we take the option we use reescramble flowrebuilder thisdump so we rebuild our flash0.ECC.bin and flash1.ECC.bin

and flash the result, when you finish you will notice that the PS3 now has a nice on but black screen, it cojemos ourfactory jig to put it into service mode and put it in factory, thenthe typical cojemos lv2diag of yore and the pup you please

(NOTE: the first pup that metais will stay in the console as the minimum version that you can downgrade then, if you want tolose 3.55 to 3.41 then you will have to put the pup up to 3.41before 3.55 or 3.55 will remain in that if cost will not rewrite thedump again to downgrade to lower the pup that you put thefirst time.)

then you put your factory lv2diag to leave the service and you’re good

Note: this applies to repair the brick Waninkoko NAND NOTDONATED plates even sem-001 (tested) (and stepdowngrade xD)

Thanks to:
all channel # irc-hispano darkps3 for supporting me for so long
to donate the INFECTUS austaquio32 to achieve to continuewith my project
to Nodial2ne paid for the help locating files in the nand
to robs1 for helping throughout the process with ideas tomake this possible

and everyone who was patient and not by private haunts mexD

 

[lange2000]

AW: Downgrade für FW 3.6x [Fat PS3]

Nur nochmal zum Hinweis:

Das Löten eines Infectus Chips ist keine einfaches unterfangen und mit Risiken verbunden.

Hier ein Beispiel bei einer 60GB Fat:

Sie müssen registriert sein, um Links zu sehen.

PS: bitte kein Frage wie funktionieren die Files auch mit meinem JB-Stick oder Ähnliches:emoticon-0143-smirk
Es funktioniert nur mit dem Infectus Chip!

 

[lange2000]

AW: Downgrade für FW 3.6x [Fat PS3]

Neuer NAND und NOR Flasher ! Progskeet!

Sie müssen registriert sein, um Links zu sehen.

Offizielle Homepage:

Spoiler

Sie müssen registriert sein, um Links zu sehen.

Es wird dadurch nicht einfacher, aber die Geschwindigkeit beim Flashen soll schneller sein.

 

[lange2000]

AW: Downgrade für FW 3.6x [Fat PS3]

Progskeet ist Online!

THE PROGSKEET BAREBONE PCB
Your one and only solution to your FLASING NEEDS…
Description:
1- Whether it is NAND, NOR or any other kind of non-volatile memory - just solder, plug in and operate!
2- Blazing fast read/write speed!
3- Beside software-side updates, you can also expect hardware updates powered by customer requests!
4- With a broad range of applications, such as EEPROM programming (among others: Altera, Lattice FPGA/CPLD), Bad flash recovery, more commonly known as "Unbricking" (Modems, video cards, cell phones, music players) and plain serial programming (manufacture of your own device).
5- Supported devices include, but are not limited to: K9F1G08, S29GL128, K8Q2815, HY27US08.
6- Industrial programmers often range in the EUR 1000+ range with limited customer support. ProgSkeet can compete with these programmers all the while maintaining low cost!
And always remember - for accuracy and speed, choose ProgSkeet!

SOME KIND OF DEVICES SUPPORTED:
XBOX360 ALL NAND SUPPORT (ALL MODELS)
PS3 ALL NAND AND NOR FLASHES SUPPORT (ALL MODELS)
WII NAND CONSOLE (ALL MODELS)
PSP NAND CONSOLE (ALL MODELS)
ANY NAND OR NOR (CAR MARKET, HANDY PHONES etc, just send us a sample of the NAND and we can add in 1 hour the support to read and write it FOR FREE!)
TRANSFER SPEED: 1MB/sec (ex. about 16 sec. to read or write a whole PS3 Slim NOR flash)

A solder-less tool will be released in the near future, and sold like an add-on.

Kosten: EUR 45.00 - 55.00

 

[HackTheNet]

Progskeet bringt bald Lötfreie downgrade Lösung für PS3

Progskeet bringt bald Lötfreie downgrade Lösung für PS3

[youtube]IgSflojpV-U[/youtube]

Erst vor kurzem stellten wir euch "Progskeet" vor, eine Lötbedingte Lösung um eure PS3 von der neusten Firmware downgraden zu können. Allerdings trauten sich viele User nicht an der eigenen PS3 wildkürlich herumzulöten. Darum gaben die Entwickler hinter diesem Board bekannt das man bald eine Lötfreie, allerdings auch eine langsamere Lösung bereitstellen möchte. In dem oben eingebunden Video wird das Progskeet Board auf einer XBox 360 demonstriert.

I would like to add one thing, in case you haven’t noticed: it’s not about the speed, that train’s long gone.
no, this time around we have the SOLDERLESS CLIP attached to the NAND.
sure, it has wires soldered to it but this is just because there is flex pcb yet to connect to progskeet
once it’s all tested and flex pcb is designed, this will be 100% solderless


DIAGRAM Changes:

05/08/2011
- updated VER-001
- Added 80 GB (taken from twitter of PHIRENZ)

04/08/2011
- Updated DIA-001 and added JSD-001, DYN-001... next update includes 2 or 3 more

03/08/2011
- Removed DualNandNew.bmp (this is for prototype, sorry)
- Added Dual NAND diagram (with the switch), read below for instructions.

02/08/2011
- Added new NAND/Dual NAND diagram. Power up the console with the switch set to “off”. When the console is on, you can switch it to “on”.

FLASHER Changes:

110802
- Added more selections to Block Count (bigger NANDs)

110803
- Fixed: issue with “Test Shorts” – ONLY USE THIS WHEN PROGSKEET IS NOT CONNECTED TO ANY DEVICE!!! OTHERWISE IT GIVES FALSE POSITIVE!!!

 

[M@libu]

AW: Downgrade für FW 3.6x [NAND+NOR]

Mal ne Frage an euch Profis
Weiß man da bzgl. PS 3 downgrade schon was neues?

 

[lange2000]

AW: Downgrade für FW 3.6x [NAND+NOR]

Erstes TUT. zum Downgrade einer 3.70 SLIM (NOR!). Anleitung Englisch! Quelle: Übernommen von PS3HAX!

Achtung! Anwendung und ausführung auf eigene Gefahr!Es könnten noch Fehler auftauchen!

STEP 1 – Preparation

Spoiler

1. A PS3 (phat or slim) running PS3 original firmware 3.70 and has NOR memory, not NAND, and has ProgSkeet/Teensy++/Clone installed(
   Sie müssen registriert sein, um Links zu sehen.
   ) – Note: This guide covers ProgSkeet install.
2. Flow Rebuilder Tool [Link veralten (gelöscht)]
3. Downgrade.bin Link veralten (gelöscht)]
4. Automated HEX File [Link veralten (gelöscht)]
5. LV2Diag [Link veralten (gelöscht) or Link ist nicht mehr aktiv.]
6. Modded LV2Diag [
   Sie müssen registriert sein, um Links zu sehen.
   ]
7. Kmeaw CFW PUP File (3.55) [Download Link veralten (gelöscht)or Mirror]
8. ProgSkeet Drivers and Latest Software [
   Sie müssen registriert sein, um Links zu sehen.
   ] – Always get the latest version of this!

STEP 2 – Some Background

Spoiler

If your a noob (and I assume most of you are), it may be a good idea to have some what of a idea on what NAND/NOR is. It is basically the PS3 flash memory. If you want to get a better understanding of the PS3 system and its various components, you should

Sie müssen registriert sein, um Links zu sehen.

. To quote:

The PS3 has 256 megabytes of flash memory to store firmware, using two NAND 128MB Samsung flash chips. The installed firmware data is interleaved between the two flash chips for speed. To prevent errors, Error Correcting Code Checksum (ECC) is added/used on the data in the PS3 flash chips. In newer PS3, a single 16MB Spansion flash chip is used.
Because of the smaller flash chips in later versions, newer firmware versions allow for the firmware data to be partially stored on the harddrive (instead of totally inside the flash), making the flash purely responsible for holding data involved in the critical booting up process. This allows for cheaper flash chips, while using the harddrive for later bootup stages.
​

To summarize now we are going to be downgrading a PS3 via NOR flasher, so the PS3 MUST have NOR memory most PS3 units have NOR now, the stock/initial PS3s (phat) that were released had NAND, there is a chart linked above so you can make sure. As of now, all SLIMs have NOR memory so your good to go

Du musst angemeldet sein, um Bilder zu sehen.

.

STEP 3 – Installing ProgSkeet

Spoiler

First thing is first you have to install ProgSkeet. You can install Teensy++ board as well, or any other ProgSkeet clone but I don’t know how they work and I assume you need to substitute the tools/files for Teensy++. So there are plenty of good threads to first checkout related to ProgSkeet, for starters this is what ProgSkeet is:

ProgSkeet is your one and only solution to your flashing needs. Whether it is NAND, NOR or any other kind of non-volatile memory – just solder, plug in and operate!
​

Works on various other devices (in addition to PS3) and consoles including Xbox 360 and Wii.
Here is a sample image of some ProgSkeet installs (gets you an idea what your getting into):

Sie müssen registriert sein, um Links zu sehen.

Sie müssen registriert sein, um Links zu sehen.

Sie müssen registriert sein, um Links zu sehen.

THERE IS CURRENTLY A SOLDERLESS CHIP IN THE MAKING, BUT AS OF NOW (8/20/2011), YOU MUST SOLDER AND PERFORM THIS METHOD IF YOU WISH TO DOWNGRADE FIRMWARE 3.70

1. Make sure your PS3 first has NOR memory, all SLIM PS3′s do, the older “phat” PS3 have NAND. Check if your console has NOR memory
   Sie müssen registriert sein, um Links zu sehen.
   .
2. Find the right pinout for your PS3 motherboard
   Sie müssen registriert sein, um Links zu sehen.
   . (Scroll down to “Pinout Gallery“). Additional ProgSkeet pinouts
   Sie müssen registriert sein, um Links zu sehen.
   . Teensy++ Pinouts located
   Sie müssen registriert sein, um Links zu sehen.
   .
3. Gather soldering tools, resin, and wire.Recommended gauge for wires: 24 (anything from 20-26 AWG is fine). Keep them at ~20cm each. – Note: 40/80 wire Floppy cables won’t work, to see a full list of compatible wires see
   Sie müssen registriert sein, um Links zu sehen.
   table.

STEP 4 – The NOR Dumping


Part A: PC Setting

Spoiler

1. HIGHLY RECOMMENDED: Install Windows XP on your computer. Windows 7 and Windows XP SP3 have reported many issues.
2. Install ProgSkeet Software + Drivers [
   Sie müssen registriert sein, um Links zu sehen.
   ]
3. Install Microsoft Visual C++ 2008 SP1 Redistributable Package (x86) [Link veralten (gelöscht)]
4. Restart your computer.
5. Launch the ProgSkeet Dumper
6. Plug in your ProgSkeet and wait for for the jingle/beep
7. Insert the following values for the NOR: if you have a SPANSION branded flash memory on your PS3 then: NOR Sector Size = 128kb / NOR Sectors = 128. If you have a SAMSUNG branded flash memory on your PS3 then NOR Sector Size = 4kb / NOR Sectors = 4096.
   Sie müssen registriert sein, um Links zu sehen.
   
   
   
8. After getting the correct values inserted, select output and then press DUMP, and you should have the exact dump generated as seen in Part B.

Part B: Creating Downgrade bin.rev

Spoiler

1. Dump the NOR from your PS3 with the ProgSkeet/Teensy++ it should be exactly 16,777,216 bytes. If it is not, go back to part A, and keep re-dumping until it is. Make sure its down to the byte.
   Sie müssen registriert sein, um Links zu sehen.
2. Next open up
   Sie müssen registriert sein, um Links zu sehen.
   , in “donador” select your nor-dump.bin.REV and for “receptor” select downgrade.bin and click GO.
   Sie müssen registriert sein, um Links zu sehen.
3. Now that your downgrade.bin is successfully hexed open Flow Rebuilder back up. Select “Byte reverse and extract a NOR Dump” and drag downgrade.bin to the bottom option and click “Execute Operation”.
   Sie müssen registriert sein, um Links zu sehen.
4. You will now be presented with an error, this is normal. All you are interested in is the file generated: “downgrade.bin.REV” -> This file will be flashed onto your PS3.

Step 5: Flashing your PS3

Spoiler

Now comes the last, and actual flashing part. Make sure you follow all the instructions above to the letter, and if you have any issues report them before continuing.

1. From the ProgSkeet flasher you downloaded in step 1, flash the file you generated in step 2 #5: downgrade.bin.REV to your PS3 (make sure your PS3 is on during this process).
2. If you flashed your PS3 correctly, your PS3 will reboot and show this message: “Push PS button”. DO NOT PRESS THE PS BUTTON!
3. Turn off the PS3 console as we will now place it in Factory/Service mode.
4. Copy these files to the ROOT (not subforulder!) of USB Mass Storage Device-: **WARNING: Make sure that this is a USB stick formatted to FAT 32. DO NOT use your MP3 player, phone, or anything except a USB stick as the timings are crucial for the downgrading process! If your having issues, we recommend you
   Sie müssen registriert sein, um Links zu sehen.
   .
   1. LV2Diag [Link veralten (gelöscht) or Link ist nicht mehr aktiv.]
   2. Kmeaw CFW PUP File (3.55) [Download Link veralten (gelöscht)or Mirror]
5. Insert to right most USB port on PS3
6. Now turn on your PS3 and leave it alone, the PS3 should turn off by itself in 10-15mins.
7. Unplug your USB from the PS3, and turn the console back on. It should boot to the XMB menu, once it does this turn your PS3 off again.
8. Now copy and replace this file on your USB: Modded LV2Diag [
   Sie müssen registriert sein, um Links zu sehen.
   ]
9. Insert once again to the right most USB port on your PS3
10. Turn on your PS3, it should turn off by itself in about ~20 seconds.

Problem Solving Tips:

FAQ: USB Formatting

Spoiler

• Don’t use any USB Mass Storage Device with enhanced functions as: encryption, fingerprintreader, U3, pincode etc.
• Don’t use USB Mass Storage Devices with a long initialisation time (e.g. some MP3 players)
• Don’t use multipartitioned USB Mass Storage Devices, only use 1 single primary FAT32 partition.
• Make sure they are formatted according to specifications with FAT32 (e.g. HP USB Format Tool – or TOKIWA / Ridgecrop FAT32 formatter)
• Most USB Mass Storage Devices that’ll work effortless with PenDrive Linux, will also work with the PS3 (for downgrading, upgrading, storage of your Game dumps and any normal filestorage under the XMB). Those USB Mass Storage Devices are most likely also the ones giving you the least problems under more exotic platforms like PSX/PSone, PS2/PStwo, Xbox/X360, Gamecube/Wii etc.

Error: libusb0.dll or libusb0.sys not found

Spoiler

The libusb-win32 Kernel Driver needed for the the flasher to get access to the USB port was not installed. Make sure you unpacked the drivers_xxxxxx file and installed the Progskeet driver (VendorID:1988 / ProductID:0001 in case you need it).

Error: side-by-side configuration is incorrect

Spoiler

In case of “the application has failed to start because its side-by-side configuration is incorrect” make sure Link veralten (gelöscht) is installed and “Windows Installer” is not disabled (set to manual or automatic) in Services.msc

Achtung! Anwendung auf eigene Gefahr!

 

[lange2000]

AW: Downgrade für FW 3.6x, 3.70 [NAND+NOR]

Zweites Tut. PS3 Slim! Anleitung Englisch! Quelle: Digitalangel.it

Fastswap: Zwischen OFW 3.70 und 3.55 hin und her wechseln.

Achtung! Anwendung auf eigene Gefahr!

Spoiler

Today i’ll write a tutorial to “fast-swap” between CFW 3.55 and OFW 3.70, using 2 HDDs… at the end of the tutorial, you i’ll be able to swap between the firmware just flashing a dump on your PS3 using Progskeet. (instead of downgrading and loosing all data).
The first steps are not so easy, so take your time and go on, by the way, you must have some skill with Progskeet, and it must be 100% working on your console.
What we need:

• PS3 Slim running with FW 3.70
• 2 Hard Disks
• Progskeet installed and working on your PS3 Slim
• Downgrade.bin edited with your personal data (there are tons of tutorials for do this)
• 3.55 Downgrade Dongle to do the downgrade process.
• Sony OFW 3.70 UPDATE.(Link ist nicht mehr aktiv.)
• CFW 3.55 KMEAW “NO CHECK” by dospiedra.(Link veralten (gelöscht))
• Lv2Diag By Jaicrab. (Link veralten (gelöscht))
• Lv2Diag “FILE 2″ to go out of Service/Factory Mode. (
  Sie müssen registriert sein, um Links zu sehen.
  )

We need 2 HDD because the NOR flashes stores some parts of the current FW on the HDD… so we will need 2 HDDs, one is for 3.55, and one is for 3.70..
We will call those HDD “A” (for 3.70) and “B” (for 3.55) dont mix them up!

Starting with a PS3 Slim with OFW 3.70.

1. Plug in HDD “B”, format and prepare it if it’s required by the PS3 and you should have your 3.70 up and running.
2. DUMP your actual NOR and call it “original dump 3.70.bin”
3. Now flash your “downgrade.bin” (edited with the personal data found in “original dump 3.70.bin”)
4. Turn on your PS3 and be sure that the PS3 is asking you to press the PS button (downgrade.bin flashed correctly IMG Removed )
5. Insert a 3.55 Downgrade dongle and enter factory/service mode.
6. Copy Lv2Diag.self by Jaicrab and the 3.55 NO CHECK UPDATE renamed as “PS3UPDAT.PUP” in the root of your USB Stick.
7. Plug in the USB Stick in the most-right USB port of your PS3 and wait for it to turn OFF.
8. Leave the factory mode using the other Lv2Diag.self
9. After the reboot, you need to configure and set up your system… now you have a fully working 3.55 CFW based on KMEAW “NO CHECK”.
10. DUMP your actual NOR and call it “swap dump 3.55.bin”
11. Unplug HDD B and Plug in HDD A.
12. Turn on your PS3, plug in your USB Stick containing official 3.70 update and press start+select when asked.
13. When the PS3 reboots, check that the system is fully working and DUMP your actual NOR and call it “swap dump 3.70.bin”.

NOW IT’S OVER! You should have “swap dump 3.55.bin” and “swap dump 3.70.bin” … Now you just have to swap HDD and flash the corrispondent dump:
HDD A = swap dump 3.70.bin
HDD B = swap dump 3.55.bin

WARNING: Do not install other CFW than the “NO CHECK” one… because it’s used to make the “fast-swap” working… if you flash something different you will not be able to go between the 2 FWs. This CFW disable the Syscon checking at the startup… so it will not freeze or complain when the syscon says “3.70″ and your FW is 3.55 IMG Removed

WARNING: In case you wanna update your console with a future “3.80″ or-so firmware. Do not update your console when you are running 3.55 firmware! You have to go to “swap dump 3.70.bin” and then update as usual (XMB or recovery)… -By the way, the downgrade is confirmed working only on 3.70… we haven’t tested it on other FWs, you could loose the possibility to go back to 3.55!-

 

[lange2000]

AW: Downgrade für FW 3.70 [NAND+NOR]

E3Flasher! Erscheinungstermin 12.Septemper!

Sie müssen registriert sein, um Links zu sehen.

Produktinhalt:

Spoiler

Link veralten (gelöscht)

Die erste Serie ist Limitiert auf 3000 Stück und ist ein Spezielles Set für Slim Konsolen zum Dualboot von 3.70<->3.55 CFW. Preis: 88$

"Now we only provide E3 flasher Limited version , it is a special suit for PS3 user, The quantity for all the world is only 3000pcs . After that we will stop and provide new version which integrate CLIP . "



Webseite:

Spoiler

Sie müssen registriert sein, um Links zu sehen.

 

[lange2000]

AW: Downgrade für FW 3.70 [NAND+NOR]

E3 Flasher Installationsanleitung(SLIM) PDF:

Spoiler

Link veralten (gelöscht)

Anders als zuerst angenommen muss gelötet werden. Allerdings denke ich das es mit den vorgegebenen Punkten am Softboard, noch relativ einfach ist.



Für die FAT(NOR/NAND) Konsolen wird ein E3 Linker mitgeliefert!

Sie müssen registriert sein, um Links zu sehen.

GrafikquelleS3CRUNCH

FAT(NAND)(CHECH A-G) 34 Lötpunkte
FAT(NOR)(CHECH H-Q) 50 Lötpunkte

 

[lange2000]

AW: Downgrade für FW 3.70 [NAND+NOR]

Progskeet bringt Lötfreie Lösung!

[YOUTUBE]zrhh8XhEKiM[/YOUTUBE]

Spoiler

We are happy to introduce you the SOLDERLESS KITS for our ProgSkeet device!
The main word is “BE FLEXIBLE” as ProgSkeet project will be the BEST TOOLKIT for the NAND and NOR flashing!!!
We present today the NAND TOOL KITS, in few days we will be ready also with NOR TOOL KITS!!! Stay Tuned
1 – PROGSKEET is 100% PIN to PIN compatible with the SOCKET tool sold from this site

Sie müssen registriert sein, um Links zu sehen.

Just connect the ProgSkeet 32 pin special flat cable. (please note that this version don’t support programming or reading with out the device is powered on. A new version will be released with the VCC pad to manage NANDS with a self power provided from PROGSKEET) 360-clip.com and also us we will offer this socket in a package together with the 20 cm 32 PIN flat cable.
2 – ADAPTOR PCB: This pcb is an adaptor from 50PIN ZIF PROGSKEET CONNECTOR (necessary for the coming “NOR SOCKET” solderless tools) to 2 x 32 PIN ZIF connector. With this adaptor progskeet is able to manage 2 NANDS on the DEVICE and also extra 2x SECONDARY NANDS (for dual nand feature). The kit include the 50 pin flat cable from PROGSKEET to ADAPTOR PCB.
3 – NAND PCB: This “optional” pcb has a 1Gbit NAND flash on board. Progkseet is able to use it like a backup nand or switch this nand and use it instead the NAND on the board of the device. The feature called “DUAL NAND” allow to support different NANDs ONLINE and test firmwares in a easy fast way. The software will be ready soon to support this feature, user can also attach a switch to progskeet to allow a fast selection of the NANDs without using the PC tool.
Progskeet support max 2 x NAND PCB on each ADAPTOR PCB, the kit include a 32 PIN 3CM flat cable (from NAND PCB to NAND SOCKET)
You can see a FULL PROGSKEET KIT SAMPLE where is clear how is the complete kit with 2x NANDS PCB and 2x NANDS SOCKETS (on the picture miss one socket sorry J ) but I think the concept is clear.
The big advantage of PROGSKEET is that can work on ANY CONSOLE / DEVICE, is study to be MODULAR and so is MUCH CHEAPER then any other solution that is specific addressed to a device.
The nice special FLAT CABLES are also easy to be fitted inside the device without bit problems, and also the KIT is removable in few minutes and is not PERMANENT.
We remember that PROGSKEET is an OPEN PROJECT study to be used in many kind of devices CONSOLES, SATELLITE, IPHONES, PENDRIVERS etc etc. “PROGSKEET NOTHING MORE THAN A GOOD NAND / NOR PROGRAMMER”.
We will send tomorrow more infos and pictures regarding PROGSKEET V1.1 “CRYSTAL BLUE LIMITED EDITION” in production in these days and available in the market soon!
Nice news also about the PROGSKEET software, that now support new nice features.
BYE FOR NOW
​

QuelleS3HAX

 

[vale]

mal ne frage, was macht der linker genau?

 

[lange2000]

mal ne frage, was macht der linker genau?

Der Linker ist dafür da, wenn man lieber lötet, statt den Clip zu benutzen.

 

[vale]

alles klar dankeschön xD
also eigentlich mehr für die nands gedacht