ich bin nun seid Tagen daran unseren Pingulux Plus wieder zum leben zu erwecken.
seid dem wir ihn nach dem Umbau des Wohnzimmers wieder aufgebaut hatten, wollte er nicht mehr
Ich habe 2 Betriebssysteme drauf (Spark & OpenATV) beide starten nicht mehr/hängen sich auf oder verfallen gelegentlich in einen Bootloop
nun habe ich das ganze mal über Terminal mitgeschnitten was er da veranstalltet, werde aber noch nicht so ganz schlau daraus.
Mitschnitt von Spark:
Mitschnitt OpenATV
Ich hoffe einer von euch kann mir Helfen den kleinen wieder auf die Beine zu helfen.
seid dem wir ihn nach dem Umbau des Wohnzimmers wieder aufgebaut hatten, wollte er nicht mehr
Ich habe 2 Betriebssysteme drauf (Spark & OpenATV) beide starten nicht mehr/hängen sich auf oder verfallen gelegentlich in einen Bootloop
nun habe ich das ganze mal über Terminal mitgeschnitten was er da veranstalltet, werde aber noch nicht so ganz schlau daraus.
Mitschnitt von Spark:
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors
0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Loading Ramdisk to 80d3c000, length 002c34df ... OK
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0
ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x0053d000 - 2897119 ...
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Loading Ramdisk to 80d3c000, length 002c34df ... OK
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x0053d000 - 2897119 ...
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_spark
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors
0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Loading Ramdisk to 80d3c000, length 002c34df ... OK
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0
ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x0053d000 - 2897119 ...Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Loading Ramdisk to 80d3c000, length 002c34df ... OK
Starting kernel console=ttyAS1,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 ip=192.168.0.69:192.168.3.119:192.168.3.1:255.255.0.0:lh:eth0
ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=4000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x0053d000 - 2897119 ...Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 0
## Booting image at a0080000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5867343 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 2970211 Bytes = 2.8 MiB
Image 1: 2897119 Bytes = 2.8 MiB
Verifying Checksum ... OK
Mitschnitt OpenATV
Board: STx7111-Mboard (MB618) [32-bit mode]
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors
0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2411335 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2411335 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0ff bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x00000000 - 0 ...
Linux version 2.6.32.71_stm24_0217 (oe1@build2) (gcc version 4.9.4 (GCC) ) #1 PREEMPT Thu Oct 26 15:21:58 CEST 2017
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: sat7111
Node 0: start_pfn = 0x40000, low = 0x50000
Zone PFN ranges:
Normal 0x00040000 -> 0x00050000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00040000 -> 0x00050000
Spark-7111 board initialization
STx7111 version 3.x
bpa2: partition 'bigphysarea' created at 0x49900000, size 25600 kB (0x01900000 B)
bpa2: partition 'LMI_IO' created at 0x4b200000, size 79872 kB (0x04e00000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0ff bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA
bpa2: partition 'bigphysarea' created at 0x40e1f000, size 24000 kB (0x01770000 B)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 118016k/262144k available (3026k kernel code, 918k data, 120k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
Failed to enable clk CLKA_PLL0LS, ignoring
Console: colour dummy device 80x25
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024)
Mount-cache hash table entries: 512
CPU: STx7111
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 922, nTxLock = 7376
msgmni has been set to 230
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "Boot firmware"
0x000000080000-0x000000780000 : "Kernel"
0x000000780000-0x000000800000 : "Reserve"
ONFI flash detected
No valid ONFI param page found (bad CRC)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
stm-nand-emi: Using legacy platform timing data
stm-nand-emi: Configuring EMI Bank 1 for NAND access
cmdlinepart partition parsing not available
Creating 4 MTD partitions on "stm-nand-emi.0":
0x000000000000-0x000000800000 : "Spark Kernel"
0x000000800000-0x000018000000 : "Spark Rootfs"
0x000018000000-0x000018800000 : "kernel"
0x000018800000-0x00001ff00000 : "rootfs"
stmmac - user ID: 0x10, Synopsys ID: 0x33
No HW DMA feature register supported
Enhanced/Alternate descriptors
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
STMMAC MII Bus: probed
eth0: PHY ID 00000000 at 0 IRQ 0 (0:00)
eth0: PHY ID 0007c0f1 at 1 IRQ 0 (0:01) active
eth0: PHY ID 00000000 at 2 IRQ 0 (0:02)
eth0: PHY ID 00000000 at 3 IRQ 0 (0:03)
eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)
eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)
eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)
eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)
eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)
eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)
eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)
eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)
eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)
eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)
eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)
eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)
eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)
eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)
eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)
eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)
eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)
eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)
eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)
eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)
eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)
eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)
eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)
eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)
eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)
eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)
eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)
eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)
nwhw_config: (eth0) setting mac address: 24:00:08:00:3e:aa
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0000000 size 0x00400000
cop. addr 0x40000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0400000 size 0x00400000
cop. addr 0x40400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elf
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7111 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
eth0: device MAC address 24:00:08:00:3e:aa
No MAC Management Counters available
IP-Config: Complete:
device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
host=LINUX7109, domain=, nis-domain=(none),
bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
Empty flash at 0x0455bff8 ends at 0x0455c000
VFS: Mounted root (jffs2 filesystem) on device 31:6.
devtmpfs: mounted
Freeing unused kernel memory: 120k freed
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to 0
seeking to 60980
seeking to 148478
seeking to 1484b0
seeking to 1484e8
seeking to 158858
seeking to 158864
seeking to 158880
seeking to 184d94
seeking to 186e00
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to 0
seeking to 5e00
seeking to 12460
seeking to 1ab60
seeking to 154300
seeking to 154338
seeking to 154370
seeking to 191a58
seeking to 191a60
seeking to 191a68
seeking to 191a70
seeking to 1aae40
seeking to 1aaf00
INIT: version 2.88 booting
Starting fake hwclock: loading system time.
Mon Feb 26 20:56:27 UTC 2018
stmcore-display: using HDMI hotplug
stmcore-display: STi7111 display probed
device probe found 2 display pipelines
requesting frm: 'component.fw', c11d6234/88da0350
stm-awg: firmware: requesting component.fw
frm 'component.fw' successfully loaded
requesting frm: 'fdvo0.fw', c11d6234/88da0950
stm-awg: firmware: requesting fdvo0.fw
loading frm: 'fdvo0.fw' failed: -2
[CEC] init - starting
[CEC] The above error is a wanted behaviour as this was a ping!
Fulan front panel driver
VfdType = 2
CpuType = 2
DisplayInfo = 1
scankeyNum = 8
swMajorVersion = 1
swSubVersion = 10
stby key 0 = 9966da25
stby key 1 = 11eeda25
stby key 2 = 1ce37887
stby key 3 = c43b7887
stby key 4 = dd227887
blue key 0 = 996640bf
blue key 1 = 11ee40bf
blue key 2 = 1ce352ad
blue key 3 = c43b52ad
blue key 4 = dd2228d7
input: fulan front panel buttons as /devices/virtual/input/input0
aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
stmfb: fb0 parameters = "1280x720-32@50:16m
al:yuv:yuv"
stmfb: fb1 parameters = "<NULL>"
Init of MME log wrapper
stm_v4l2_register_driver: driver 'stmvout' registered
stm_v4l2_register_driver: driver 'stmvbi' registered
snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
pseudocard: 1 pseudo soundcard(s) found
stv090x loaded
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 4096, waitMS = 20, enableStatistic = 0)
no swts ->routing streams from dvr0 direct to the player
DVB: registering new adapter (STM Streamer)
0: DeviceContext 894b6088, DvbDemux 894b638c, DmxDevice 894b6574
CaInit()
Initializing CI Controller
ptiInit context = 894b6088, demux = 894b638c
[Spark] Init Stream Routing...
Load real TC Code
TC_Data = fe238000, TC_Code = fe23c000
Readback TC ... successfull
using videoMem = 770048 (packets = 4096)
pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
DMA(0) base = 4ad80000, top = 4ae3c000, buffer = 4ad80000, size 770048
freeBuffer(): free = 1
stv090x_register_frontend: stv090x DVB: 0.11
pti_task: using 1 dma channel
tuner = 1
stv090x_register_frontend: init tuner 0
> (bus = 3) init_stv090x_device
i2c adapter = 0x89658018
i2c addr = 68
tuner enable = 0.0
frontend_init >
ix7306_write ucIOBuffer 4 Err = 0
ix7306_write ucIOBuffer 1 Err = 0
ix7306_write ucIOBuffer Err 2 = 0
ix7306_read Err = 0 ucData = 0x18
========tuner_sharp7306_identify =====
tuner_Sharp7306 is Identified
frontend_init: attached
ix7306_attach: Attaching Sharp BS2S7HZ7306A IX7306 8PSK/QPSK tuner
frontend_init: IX7306 attached
stv090x_init: AGCRF1CFG = 0x10
stv090x_init: AGCRF2CFG = 0x13
init_stv090x_device: Call dvb_register_frontend (adapter = 0x894b603c)
DVB: registering adapter 0 frontend 0 (STV090x Multistandard)...
stv090x_register_frontend: <
Free session: 0
Using session 0
Descrambler Handler = 40000
install_e2_procs(): entry already in use 'progress'
install_e2_procs(): entry already in use 'stb/fp/was_timer_wakeup'
1: DeviceContext 894b6610, DvbDemux 894b6914, DmxDevice 894b6afc
CaInit()
ptiInit context = 894b6610, demux = 894b6914
Free session: 1
Using session 1
Descrambler Handler = 41000
2: DeviceContext 894b6b98, DvbDemux 894b6e9c, DmxDevice 894b7084
CaInit()
ptiInit context = 894b6b98, demux = 894b6e9c
convert_source(): invalid frontend source (2)
Free session: 2
Using session 2
Descrambler Handler = 42000
3: DeviceContext 894b7120, DvbDemux 894b7424, DmxDevice 894b760c
ptiInit context = 894b7120, demux = 894b7424
convert_source(): invalid frontend source (3)
Descrambler Handler = -2
stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered
OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0
AllocatorLoadModule : Allocator device loaded
OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0
H264ppLoadModule : H264pp device loaded
(bpamem_init): BPAMem driver register result = 0
Registering device 'sc', major '169'
Version of smartcard driver: [1.0.1]
ramzswap: disk size not provided. You can use disksize_kb module param to specify size.
Using default: (25% of RAM).
ramzswap: disk size set to 29532 kB
ramzswap: Initialization done!
Adding 29528k swap on /dev/ramzswap0. Priority:-1 extents:1 across:29528k SS
LinuxDvb
vbPlaybackCreate: Playback 882b4c60
Unaligned userspace access in "mdev" pid=801 pc=0x2961e624 ins=0x6144
Sending SIGBUS to "mdev" due to unaligned access (PC 2961e624 PR 295e875a)
ALSA: Restoring mixer settings...
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
No state is present for card STx7111
Found hardware: "STx7111" "" "" "" ""
Hardware is initialized using a generic method
Simple mixer control 'Analog',0
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
No state is present for card STx7111
No state is present for card MIXER0
Mono: Playback 7 [61%] [on]
Found hardware: "Pseudo Mixer" "Pseudo Mixer" "" "" ""
Hardware is initialized using a generic method
Simple mixer control 'HDMI',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 7 [61%] [on]
Mono: Playback 7 [61%] [on]
No state is present for card MIXER0
Unable to handle kernel paging request at virtual address 6a632fa6
Unable to handle kernel paging request at virtual address 0001802c
pgd = 88217000
[0001802c] *pgd=00000000
Oops: 0001 [#1]
last sysfs file: /sys/devices/virtual/bdi/254:0/uevent
Modules linked in: ramzswap smartcard bpamem silencegen platform
info: Disregarding any EPLD
U-Boot 1.3.1 (Nov 15 2010 - 17:57:53) - stm23_0043 - YW 1.0.018 Rel
DRAM: 128 MiB
NOR: 8 MiB
NAND: 512 MiB
In: serial
Out: serial
Err: serial
IdentID : 09 00 08 00 00 3e aa
Hit ESC to stop autoboot: 3
Force command mode:Select boot (current boot system : spark):
1. spark(up key)
2. enigma2(down key)
3. RS232 Upgrade u-boot(left key)
4. Force into factory mode(right key)
Input Select:
set bootargs to bootargs_enigma2
Unprotecting Flash...
.. done
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash...
........ done
Protecting Flash...
.. done
Protected 2 sectors
0
Loading from NAND 512MiB 3,3V 8-bit, offset 0x18000000
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2411335 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2411335 Bytes = 2.3 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
found phy at addres = 1
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = 908003eaa
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0
ff bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AA - 0x00000000 - 0 ...Linux version 2.6.32.71_stm24_0217 (oe1@build2) (gcc version 4.9.4 (GCC) ) #1 PREEMPT Thu Oct 26 15:21:58 CEST 2017
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000000
... INITRD_START - 00000000
... INITRD_SIZE - 00000000
Booting machvec: sat7111
Node 0: start_pfn = 0x40000, low = 0x50000
Zone PFN ranges:
Normal 0x00040000 -> 0x00050000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00040000 -> 0x00050000
Spark-7111 board initialization
STx7111 version 3.x
bpa2: partition 'bigphysarea' created at 0x49900000, size 25600 kB (0x01900000 B)
bpa2: partition 'LMI_IO' created at 0x4b200000, size 79872 kB (0x04e00000 B)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock6 rootfstype=jffs2 rw init=/bin/devinit coprocessor_mem=4m@0x40000000,4m@0x40400000 printk=1 rw ip=172.100.100.249:172.100.100.174:172.100.100.174:255.255.0.0:LINUX7109:eth0
ff bigphysarea=6000 stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 nwhwconf=device:eth0,hwaddr:24:00:08:00:3E:AA Manufacture=Spark-Project STB_ID=09:00:08:00:00:3E:AAbpa2: partition 'bigphysarea' created at 0x40e1f000, size 24000 kB (0x01770000 B)
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009a10
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 118016k/262144k available (3026k kernel code, 918k data, 120k init)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:600
Failed to enable clk CLKA_PLL0LS, ignoring
Console: colour dummy device 80x25
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 448.51 BogoMIPS (lpj=897024)
Mount-cache hash table entries: 512
CPU: STx7111
devtmpfs: initialized
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering DMA API.
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
sq: Registering store queue API.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 922, nTxLock = 7376
msgmni has been set to 230
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
lirc_dev: IR Remote Control driver registered, major 61
lirc-stm: probe found data for platform device lirc-stm
lirc-stm: STM LIRC plugin using IRQ 125 in IR mode
lirc_dev: lirc_register_driver: sample_rate: 0
STMicroelectronics LIRC driver initialized.
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
physmap platform flash device: 00800000 at 00000000
physmap-flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x000000000000-0x000000080000 : "Boot firmware"
0x000000080000-0x000000780000 : "Kernel"
0x000000780000-0x000000800000 : "Reserve"
ONFI flash detected
No valid ONFI param page found (bad CRC)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
stm-nand-emi: Using legacy platform timing data
stm-nand-emi: Configuring EMI Bank 1 for NAND access
cmdlinepart partition parsing not available
Creating 4 MTD partitions on "stm-nand-emi.0":
0x000000000000-0x000000800000 : "Spark Kernel"
0x000000800000-0x000018000000 : "Spark Rootfs"
0x000018000000-0x000018800000 : "kernel"
0x000018800000-0x00001ff00000 : "rootfs"
stmmac - user ID: 0x10, Synopsys ID: 0x33
No HW DMA feature register supported
Enhanced/Alternate descriptors
RX Checksum Offload Engine supported
TX Checksum insertion supported
Wake-Up On Lan supported
STMMAC MII Bus: probed
eth0: PHY ID 00000000 at 0 IRQ 0 (0:00)
eth0: PHY ID 0007c0f1 at 1 IRQ 0 (0:01) active
eth0: PHY ID 00000000 at 2 IRQ 0 (0:02)
eth0: PHY ID 00000000 at 3 IRQ 0 (0:03)
eth0: PHY ID 00000000 at 4 IRQ 0 (0:04)
eth0: PHY ID 00000000 at 5 IRQ 0 (0:05)
eth0: PHY ID 00000000 at 6 IRQ 0 (0:06)
eth0: PHY ID 00000000 at 7 IRQ 0 (0:07)
eth0: PHY ID 00000000 at 8 IRQ 0 (0:08)
eth0: PHY ID 00000000 at 9 IRQ 0 (0:09)
eth0: PHY ID 00000000 at 10 IRQ 0 (0:0a)
eth0: PHY ID 00000000 at 11 IRQ 0 (0:0b)
eth0: PHY ID 00000000 at 12 IRQ 0 (0:0c)
eth0: PHY ID 00000000 at 13 IRQ 0 (0:0d)
eth0: PHY ID 00000000 at 14 IRQ 0 (0:0e)
eth0: PHY ID 00000000 at 15 IRQ 0 (0:0f)
eth0: PHY ID 00000000 at 16 IRQ 0 (0:10)
eth0: PHY ID 00000000 at 17 IRQ 0 (0:11)
eth0: PHY ID 00000000 at 18 IRQ 0 (0:12)
eth0: PHY ID 00000000 at 19 IRQ 0 (0:13)
eth0: PHY ID 00000000 at 20 IRQ 0 (0:14)
eth0: PHY ID 00000000 at 21 IRQ 0 (0:15)
eth0: PHY ID 00000000 at 22 IRQ 0 (0:16)
eth0: PHY ID 00000000 at 23 IRQ 0 (0:17)
eth0: PHY ID 00000000 at 24 IRQ 0 (0:18)
eth0: PHY ID 00000000 at 25 IRQ 0 (0:19)
eth0: PHY ID 00000000 at 26 IRQ 0 (0:1a)
eth0: PHY ID 00000000 at 27 IRQ 0 (0:1b)
eth0: PHY ID 00000000 at 28 IRQ 0 (0:1c)
eth0: PHY ID 00000000 at 29 IRQ 0 (0:1d)
eth0: PHY ID 00000000 at 30 IRQ 0 (0:1e)
eth0: PHY ID 00000000 at 31 IRQ 0 (0:1f)
nwhw_config: (eth0) setting mac address: 24:00:08:00:3e:aa
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm-ehci stm-ehci.0: STMicroelectronics EHCI Host Controller
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: STMicroelectronics OHCI Host Controller
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
Linux video capture interface: v2.00
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st231.0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0000000 size 0x00400000
cop. addr 0x40000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231.1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa0400000 size 0x00400000
cop. addr 0x40400000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
DMA: Registering fdma_dmac.0 handler (16 channels).
IRQ 140/fdma_dmac.0: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.0: firmware: using built-in firmware fdma_STx7111_0.elf
DMA: Registering fdma_dmac.1 handler (16 channels).
platform fdma_dmac.0: SLIM hw 0.0, FDMA fw 2.3
IRQ 141/fdma_dmac.1: IRQF_DISABLED is not guaranteed on shared IRQs
stm-fdma stm-fdma.1: firmware: using built-in firmware fdma_STx7111_1.elf
platform fdma_dmac.1: SLIM hw 0.0, FDMA fw 2.6
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
#0: STMicroelectronics STx7111 cut 3.x SOC audio subsystem
TCP cubic registered
NET: Registered protocol family 10
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
eth0: device MAC address 24:00:08:00:3e:aa
No MAC Management Counters available
IP-Config: Complete:
device=eth0, addr=172.100.100.249, mask=255.255.0.0, gw=172.100.100.174,
host=LINUX7109, domain=, nis-domain=(none),
bootserver=172.100.100.174, rootserver=172.100.100.174, rootpath=
Empty flash at 0x0455bff8 ends at 0x0455c000
VFS: Mounted root (jffs2 filesystem) on device 31:6.
devtmpfs: mounted
Freeing unused kernel memory: 120k freed
copLoadFile (file /boot/video.elf)
ustslave: Kernel Version: 24
base_address 0x40000000
seeking to 0
seeking to 60980
seeking to 148478
seeking to 1484b0
seeking to 1484e8
seeking to 158858
seeking to 158864
seeking to 158880
seeking to 184d94
seeking to 186e00
copLoadFile (file /boot/audio.elf)
ustslave: Kernel Version: 24
base_address 0x40400000
seeking to 0
seeking to 5e00
seeking to 12460
seeking to 1ab60
seeking to 154300
seeking to 154338
seeking to 154370
seeking to 191a58
seeking to 191a60
seeking to 191a68
seeking to 191a70
seeking to 1aae40
seeking to 1aaf00
INIT: version 2.88 booting
Starting fake hwclock: loading system time.
Mon Feb 26 20:56:27 UTC 2018
stmcore-display: using HDMI hotplug
stmcore-display: STi7111 display probed
device probe found 2 display pipelines
requesting frm: 'component.fw', c11d6234/88da0350
stm-awg: firmware: requesting component.fw
frm 'component.fw' successfully loaded
requesting frm: 'fdvo0.fw', c11d6234/88da0950
stm-awg: firmware: requesting fdvo0.fw
loading frm: 'fdvo0.fw' failed: -2
[CEC] init - starting
[CEC] The above error is a wanted behaviour as this was a ping!
Fulan front panel driver
VfdType = 2
CpuType = 2
DisplayInfo = 1
scankeyNum = 8
swMajorVersion = 1
swSubVersion = 10
stby key 0 = 9966da25
stby key 1 = 11eeda25
stby key 2 = 1ce37887
stby key 3 = c43b7887
stby key 4 = dd227887
blue key 0 = 996640bf
blue key 1 = 11ee40bf
blue key 2 = 1ce352ad
blue key 3 = c43b52ad
blue key 4 = dd2228d7
input: fulan front panel buttons as /devices/virtual/input/input0
aotom-rtc aotom-rtc: rtc core: registered aotom as rtc0
stmfb: fb0 parameters = "1280x720-32@50:16m
al:yuv:yuv"stmfb: fb1 parameters = "<NULL>"
Init of MME log wrapper
stm_v4l2_register_driver: driver 'stmvout' registered
stm_v4l2_register_driver: driver 'stmvbi' registered
snd_pseudo snd_pseudo.0: firmware: requesting downmix.fw
pseudocard: 1 pseudo soundcard(s) found
stv090x loaded
pti: module license 'NO' taints kernel.
Disabling lock debugging due to kernel taint
pti loaded (videoMem = 4096, waitMS = 20, enableStatistic = 0)
no swts ->routing streams from dvr0 direct to the player
DVB: registering new adapter (STM Streamer)
0: DeviceContext 894b6088, DvbDemux 894b638c, DmxDevice 894b6574
CaInit()
Initializing CI Controller
ptiInit context = 894b6088, demux = 894b638c
[Spark] Init Stream Routing...
Load real TC Code
TC_Data = fe238000, TC_Code = fe23c000
Readback TC ... successfull
using videoMem = 770048 (packets = 4096)
pti: pti_buffer_pool_init: allocate 188 pages (770048 bytes)
DMA(0) base = 4ad80000, top = 4ae3c000, buffer = 4ad80000, size 770048
freeBuffer(): free = 1
stv090x_register_frontend: stv090x DVB: 0.11
pti_task: using 1 dma channel
tuner = 1
stv090x_register_frontend: init tuner 0
> (bus = 3) init_stv090x_device
i2c adapter = 0x89658018
i2c addr = 68
tuner enable = 0.0
frontend_init >
ix7306_write ucIOBuffer 4 Err = 0
ix7306_write ucIOBuffer 1 Err = 0
ix7306_write ucIOBuffer Err 2 = 0
ix7306_read Err = 0 ucData = 0x18
========tuner_sharp7306_identify =====
tuner_Sharp7306 is Identified
frontend_init: attached
ix7306_attach: Attaching Sharp BS2S7HZ7306A IX7306 8PSK/QPSK tuner
frontend_init: IX7306 attached
stv090x_init: AGCRF1CFG = 0x10
stv090x_init: AGCRF2CFG = 0x13
init_stv090x_device: Call dvb_register_frontend (adapter = 0x894b603c)
DVB: registering adapter 0 frontend 0 (STV090x Multistandard)...
stv090x_register_frontend: <
Free session: 0
Using session 0
Descrambler Handler = 40000
install_e2_procs(): entry already in use 'progress'
install_e2_procs(): entry already in use 'stb/fp/was_timer_wakeup'
1: DeviceContext 894b6610, DvbDemux 894b6914, DmxDevice 894b6afc
CaInit()
ptiInit context = 894b6610, demux = 894b6914
Free session: 1
Using session 1
Descrambler Handler = 41000
2: DeviceContext 894b6b98, DvbDemux 894b6e9c, DmxDevice 894b7084
CaInit()
ptiInit context = 894b6b98, demux = 894b6e9c
convert_source(): invalid frontend source (2)
Free session: 2
Using session 2
Descrambler Handler = 42000
3: DeviceContext 894b7120, DvbDemux 894b7424, DmxDevice 894b760c
ptiInit context = 894b7120, demux = 894b7424
convert_source(): invalid frontend source (3)
Descrambler Handler = -2
stm_v4l2_register_driver: driver 'Linux DVB Overlay' registered
OSDEV_LinkDevice - /dev/allocator, Major 245, Minor 0
AllocatorLoadModule : Allocator device loaded
OSDEV_LinkDevice - /dev/h264pp, Major 246, Minor 0
H264ppLoadModule : H264pp device loaded
(bpamem_init): BPAMem driver register result = 0
Registering device 'sc', major '169'
Version of smartcard driver: [1.0.1]
ramzswap: disk size not provided. You can use disksize_kb module param to specify size.
Using default: (25% of RAM).
ramzswap: disk size set to 29532 kB
ramzswap: Initialization done!
Adding 29528k swap on /dev/ramzswap0. Priority:-1 extents:1 across:29528k SS
LinuxDvb
vbPlaybackCreate: Playback 882b4c60Unaligned userspace access in "mdev" pid=801 pc=0x2961e624 ins=0x6144
Sending SIGBUS to "mdev" due to unaligned access (PC 2961e624 PR 295e875a)
ALSA: Restoring mixer settings...
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
vm.swappiness = 30
No state is present for card STx7111
Found hardware: "STx7111" "" "" "" ""
Hardware is initialized using a generic method
Simple mixer control 'Analog',0
Simple mixer control 'SPDIF',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
No state is present for card STx7111
No state is present for card MIXER0
Mono: Playback 7 [61%] [on]
Found hardware: "Pseudo Mixer" "Pseudo Mixer" "" "" ""
Hardware is initialized using a generic method
Simple mixer control 'HDMI',0
Capabilities: pvolume pvolume-joined pswitch pswitch-joined
Playback channels: Mono
Limits: Playback -31 - 31
Mono: Playback 7 [61%] [on]
Mono: Playback 7 [61%] [on]
No state is present for card MIXER0
Unable to handle kernel paging request at virtual address 6a632fa6
Unable to handle kernel paging request at virtual address 0001802c
pgd = 88217000
[0001802c] *pgd=00000000
Oops: 0001 [#1]
last sysfs file: /sys/devices/virtual/bdi/254:0/uevent
Modules linked in: ramzswap smartcard bpamem silencegen platform
Ich hoffe einer von euch kann mir Helfen den kleinen wieder auf die Beine zu helfen.
