Dies ist eine mobil optimierte Seite, die schnell lädt. Wenn Sie die Seite ohne Optimierung laden möchten, dann klicken Sie auf diesen Text.

HD02 will einfach in der mouse nicht gehen / mouse ttyusb am qnap herausfinden

AW: mouse ttyusb am qnap herausfinden

Code: 
Bus 001 Device 010: ID 0403:6001 Future Technology Devices International, Ltd FT232 USB-Serial (UART) IC

muss auch 10 sein und nicht 0

setzt dich doch mal mit UDEV auseinander ... da is es dann egal welche device # die mouse bekommt ...
 
AW: mouse ttyusb am qnap herausfinden

wie ist deine Easy eingestellt?
Schalterstellung?

und nehme mal alle lb_*, ecm* und den ident Parameter raus!
 
AW: mouse ttyusb am qnap herausfinden

u,u,u,o
[reader]
label = hd02
enable = 0
protocol = mouse
device = /dev/ttyUSB0
autospeed = 0
caid = 1843
boxkey = A******7C
rsakey = BF3******CA4DD5
detect = cd
group = 3
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-s = 1
saveemm-g = 1
auprovid = 003411

immer noch

2014/03/26 16:38:58 129748 h hd02 [mouse] Restarting reader
2014/03/26 16:38:58 129748 h hd02 [mouse] creating thread for device /dev/ttyUSB0
2014/03/26 16:38:58 1813B0 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=357, cardmhz=357)
2014/03/26 16:38:59 1813B0 r hd02 [mouse] card detected
2014/03/26 16:39:00 1813B0 r hd02 [mouse] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2014/03/26 16:39:00 1813B0 r hd02 [mouse] Init card protocol T1, FI=9, F=512, D=16, N=255
2014/03/26 16:39:00 1813B0 r hd02 [mouse] Setting baudrate to 111600 bps
2014/03/26 16:39:00 1813B0 r hd02 [mouse] Calculated work ETU is 8.96 us reader mhz = 357
2014/03/26 16:39:00 1813B0 r hd02 [mouse] ATR Fsmax is 5 MHz, clocking card to wanted user cardspeed off 3.57 MHz (specified in reader->mhz)
2014/03/26 16:39:18 1813B0 r hd02 [mouse] Warning: Card returned error on setting ifsd value to 160
2014/03/26 16:39:19 1813B0 r hd02 [mouse] detect native nagra card
2014/03/26 16:39:29 1813B0 r hd02 [mouse] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
 
AW: mouse ttyusb am qnap herausfinden

Easymouse scheint okay.

setze mal mhz wie folgt:

Code: 
mhz = 369

Wenn das nichts hilft evtl. mal auf 6Mhz umstellen!

Code: 
Easy: u,u,o,o

Im reader:
Code: 
mhz = 600
cardmhz = 600
 
AW: mouse ttyusb am qnap herausfinden

2014/03/26 16:49:58 129748 h hd02 [mouse] Restarting reader
2014/03/26 16:49:58 129748 h hd02 [mouse] creating thread for device /dev/ttyUSB0
2014/03/26 16:49:58 40510BF8 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=369, cardmhz=357)
2014/03/26 16:49:59 40510BF8 r hd02 [mouse] card detected
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] ATR: 3F 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] Specific mode: speed 'implicitly defined', not sure how to proceed, assuming default values
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] Init card protocol T1, FI=1, F=372, D=1, N=0
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] Setting baudrate to 9600 bps
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] Calculated work ETU is 100.81 us reader mhz = 369
2014/03/26 16:50:00 40510BF8 r hd02 [mouse] ATR Fsmax is 5 MHz, clocking card to wanted user cardspeed off 3.69 MHz (specified in reader->mhz)
2014/03/26 16:50:01 40510BF8 r hd02 [mouse] card system not supported
2014/03/26 16:50:01 40510BF8 r hd02 [mouse] Normal mode failed, reverting to Deprecated Mode
2014/03/26 16:50:05 40510BF8 r hd02 [mouse] Error activating card.
 
Zuletzt bearbeitet von einem Moderator:
AW: mouse ttyusb am qnap herausfinden

poste mal bitte deine komplette oscam.server ...
 
AW: mouse ttyusb am qnap herausfinden

# oscam.server generated automatically by Streamboard OSCAM 1.20-unstable_svn SVN r9479
# Read more:
Sie müssen registriert sein, um Links zu sehen.



[reader]
label = KabelDeutschland
protocol = smartreader
device = 001:005
lb_whitelist_services = kdg-digitalesendewelt,kdg-digitalesendewelt-radio,kdg-premiumextra,kdg-premiumhd-sd,kdg-premiumhd,kdg-privathd,kdg-premiumextra-radio
smargopatch = 1
caid = 09C7
boxid = 12345678
ins7e11 = 15
ecmwhitelist = 09C7:5D,5E,5F,60,61,62,63,64,77,78,7A,7C
detect = cd
mhz = 534
cardmhz = 369
group = 1
emmcache = 1,1,2
blockemm-unknown = 1
blockemm-s = 1
blockemm-g = 1
saveemm-u = 1
lb_weight = 400
cccreshare = 1
ndsversion = 2


[reader]
label = redlight_hd
protocol = smartreader
device = 001:006
lb_whitelist_services = redlight
smargopatch = 1
caid = 0500
ecmwhitelist = 0500@043800:35,39,3A,3E,43,44,46,48,4D
ecmheaderwhitelist = 0500@043800:817032,807032,817041,807041,817045,807045,81703B,80703B,81704A,80704A,817040,807040,817036,807036,817037,807037,817043,807043
detect = cd
mhz = 534
cardmhz = 369
group = 2
emmcache = 1,1,2
blockemm-unknown = 1
lb_weight = 400
cccreshare = 1


[reader]
label = hd02
protocol = mouse
device = /dev/ttyUSB0
autospeed = 0
caid = 1843
boxkey = A****7C
rsakey = BF*****A4DD5
detect = cd
mhz = 369
group = 3
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-s = 1
saveemm-g = 1
auprovid = 003411
 
AW: mouse ttyusb am qnap herausfinden

Hast du 6Mhz-Variante schon getestet (siehe Post #19)?
 
AW: mouse ttyusb am qnap herausfinden

u,u,o,6mhz
2014/03/26 16:57:49 1C9160 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=369, cardmhz=357)
2014/03/26 16:57:49 1C9160 r hd02 [mouse] card detected
2014/03/26 16:57:51 1C9160 r hd02 [mouse] ATR: E1 E0 ED FF 60 C9 63
2014/03/26 16:57:51 1C9160 r hd02 [mouse] ERROR: Could not read reader->convention
2014/03/26 16:57:51 1C9160 r hd02 [mouse] Error activating card.
2014/03/26 16:57:57 1C9160 r hd02 [mouse] ATR: F8 4C 56
2014/03/26 16:57:57 1C9160 r hd02 [mouse] ERROR: Could not read reader->convention
2014/03/26 16:57:57 1C9160 r hd02 [mouse] Error activating card.
2014/03/26 16:57:57 1C9160 r hd02 [mouse] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2014/03/26 16:57:57 1C9160 r hd02 [mouse] card initializing error

das selbe
 
AW: mouse ttyusb am qnap herausfinden

und wenn das nicht hilft, dann stell mal die Easymouse auf 5V ,Smartmouse , oben , 3,578mhz
Zum Vergrößern anklicken....
Ähm..
Die Einstellung gibt es nicht, oder?
Dritter Schalter 'oben' ist ab 6Mhz aufwärts!

2014/03/26 16:57:49 1C9160 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=369, cardmhz=357)
Zum Vergrößern anklicken....

Du must auch die mhz Einstellung im reader ändern!! Siehe Post #19!!
 
AW: mouse ttyusb am qnap herausfinden

u,u,o,6mhz

3. schalter oben ist nen pfeil nach rechts zum 4. der steht auf 6mhz
3. nach unten 3.579 mhz

reader beides auf 600 stellt

2014/03/26 17:04:40 1C9160 r hd02 [mouse] creating thread for device /dev/ttyUSB0
2014/03/26 17:04:40 1832D0 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=600, cardmhz=600)
2014/03/26 17:04:41 1832D0 r hd02 [mouse] card detected
2014/03/26 17:04:43 1832D0 r hd02 [mouse] ATR: F0 FD FF 70 FB 7C F6 FE DE F4 ED AF EF 5F F4 FD FB
2014/03/26 17:04:43 1832D0 r hd02 [mouse] ERROR: Could not read reader->convention
2014/03/26 17:04:43 1832D0 r hd02 [mouse] Error activating card.
2014/03/26 17:04:45 1832D0 r hd02 [mouse] ATR: F0 FD FF 70 FB 7C F6 FE DE F4 ED AF EF 5F F4 FD FB
2014/03/26 17:04:45 1832D0 r hd02 [mouse] ERROR: Could not read reader->convention
2014/03/26 17:04:45 1832D0 r hd02 [mouse] Error activating card.
2014/03/26 17:04:46 1832D0 r hd02 [mouse] ATR: F0 FD FF 70 FB 7C F6 FE DE F4 ED AF EF 5F F4 FD FB
2014/03/26 17:04:46 1832D0 r hd02 [mouse] ERROR: Could not read reader->convention
2014/03/26 17:04:46 1832D0 r hd02 [mouse] Error activating card.
2014/03/26 17:04:47 1832D0 r hd02 [mouse] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2014/03/26 17:04:47 1832D0 r hd02 [mouse] card initializing error
 
AW: mouse ttyusb am qnap herausfinden

Stell die Easy zurück auf u,u,u,egal

im Reader:

Code: 
mhz = 369
cardmhz = 368
 
AW: mouse ttyusb am qnap herausfinden

log:
2014/03/26 17:10:21 129748 h hd02 [mouse] Restarting reader
2014/03/26 17:10:21 129748 h hd02 [mouse] creating thread for device /dev/ttyUSB0
2014/03/26 17:10:22 4050D158 r hd02 [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=369, cardmhz=368)
2014/03/26 17:10:23 4050D158 r hd02 [mouse] card detected
2014/03/26 17:10:24 4050D158 r hd02 [mouse] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2014/03/26 17:10:24 4050D158 r hd02 [mouse] Init card protocol T1, FI=9, F=512, D=16, N=255
2014/03/26 17:10:24 4050D158 r hd02 [mouse] Setting baudrate to 115200 bps
2014/03/26 17:10:24 4050D158 r hd02 [mouse] Calculated work ETU is 8.67 us reader mhz = 369
2014/03/26 17:10:24 4050D158 r hd02 [mouse] ATR Fsmax is 5 MHz, clocking card to wanted user cardspeed off 3.69 MHz (specified in reader->mhz)
2014/03/26 17:10:27 4050D158 r hd02 [mouse] Warning: Card returned error on setting ifsd value to 160
2014/03/26 17:10:28 4050D158 r hd02 [mouse] detect native nagra card
2014/03/26 17:10:38 4050D158 r hd02 [mouse] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
2014/03/26 17:10:52 4050D158 r hd02 [mouse] T1 Resync command error, trying to reactivate!
2014/03/26 17:11:22 4050D158 r hd02 [mouse] card system not supported
2014/03/26 17:11:22 4050D158 r hd02 [mouse] Normal mode failed, reverting to Deprecated Mode

.server
[reader]label = hd02
protocol = mouse
device = /dev/ttyUSB0
autospeed = 0
caid = 1843
boxkey = A76xxxxxxx37C
rsakey = BF3xxxxxxxxxxxxxxxxxxDD5
detect = cd
mhz = 369
cardmhz = 368
group = 3
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-s = 1
saveemm-g = 1
auprovid = 003411
 
Zuletzt bearbeitet von einem Moderator:
Du musst dich einloggen oder registrieren, um hier zu antworten.

Ähnliche Themen

A
gelöst P4 Karte provid mapping?
Antworten
4
Aufrufe
212
atzplzw
A
E
HD02 Dunkel und ich finde den Fehler in der Konfig nicht
Antworten
12
Aufrufe
561
telecomic
W
gelöst HD+ 05 Karte aktivieren
2 3
Antworten
34
Aufrufe
2K
wfra1
W
M
gelöst VuZero4K - Probleme mit neuer ORF-Karte
2
Antworten
15
Aufrufe
831
Token
T
F
gelöst T1 Resync command error, ERROR: IO_Serial_Write
Antworten
9
Aufrufe
399
Kind regards
Menü
Anmelden
Registrieren
Für die Nutzung dieser Website sind Cookies erforderlich. Du musst diese akzeptieren, um die Website weiter nutzen zu können. Erfahre mehr…