HD+ bleibt dunkel...

[tom_63]

AW: HD+ bleibt dunkel...

in oscam.server wäre

mhz = 540
cardmhz = 2700

korrekt

 

[nando0707]

AW: HD+ bleibt dunkel...

keine Änderung

hier der LOG

Spoiler

2015/05/16 10:53:37 C4CBE0 r hdplus02 [internal] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2015/05/16 10:53:37 C4CBE0 r hdplus02 [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
2015/05/16 10:53:37 C4CBE0 r hdplus02 [internal] TEST tempo mhz check = 500 mhz
2015/05/16 10:53:37 C4CBE0 r hdplus02 [internal] Calculated work ETU is 5.93 us reader mhz = 540
2015/05/16 10:53:37 C4CBE0 r hdplus02 [internal] Sent reader settings T=0 fs=5 ETU=32 WWT=0 CWT=139 BWT=178571 EGT=0 clock=0 check=0 P=5 I=25 U=0
2015/05/16 10:53:38 C4CBE0 r hdplus02 [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 5.40 Mhz (nearest possible mhz specified reader->cardmhz)
2015/05/16 10:53:38 C4CBE0 r hdplus02 [internal] Card responded ok for ifsd request of 160
2015/05/16 10:53:40 C4CBE0 r hdplus02 [internal] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
2015/05/16 10:53:41 C4CBE0 r hdplus02 [internal] T1 Resync command error, trying to reactivate!
2015/05/16 10:53:41 C4CBE0 r hdplus02 [internal] Card is present in readerslot!
2015/05/16 10:53:41 C4CBE0 r hdplus02 [internal] Set reader parameters!
2015/05/16 10:53:41 C4CBE0 r hdplus02 [internal] Sent reader setting at cardinit T=0 fs=27 ETU=372 WWT=0 CWT=0 BWT=0 EGT=0 clock=0 check=0 P=0 I=0 U=0
2015/05/16 10:53:41 C4CBE0 r hdplus02 [internal] Reset internal cardreader!
2015/05/16 10:53:42 C4CBE0 r hdplus02 [internal] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2015/05/16 10:53:42 C4CBE0 r hdplus02 [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
2015/05/16 10:53:42 C4CBE0 r hdplus02 [internal] TEST tempo mhz check = 500 mhz
2015/05/16 10:53:42 C4CBE0 r hdplus02 [internal] Calculated work ETU is 5.93 us reader mhz = 540
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] Sent reader settings T=0 fs=5 ETU=32 WWT=0 CWT=139 BWT=178571 EGT=0 clock=0 check=0 P=5 I=25 U=0
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 5.40 Mhz (nearest possible mhz specified reader->cardmhz)
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] Card responded ok for ifsd request of 160
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] card system not supported
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2015/05/16 10:53:43 C4CBE0 r hdplus02 [internal] card initializing error
2015/05/16 10:53:44 0 s init for all local cards done
2015/05/16 10:53:44 0 s anti cascading disabled
2015/05/16 10:54:25 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:25 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:25 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:26 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:26 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:26 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:27 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:27 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:27 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:28 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:28 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:28 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:28 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:29 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:29 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:29 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:30 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:30 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:30 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:31 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:31 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:31 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:31 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:32 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:32 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:32 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:33 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!
2015/05/16 10:54:33 C51CF0 c [DVBAPI] Demuxer #0 impossible to descramble PID #1 CAID 1843 PROVID 000000 ECMPID 19EA PMTPID 0060 (NO MATCHING READER)
2015/05/16 10:54:33 C51CF0 c [DVBAPI] Demuxer #0 (re)starting decodingrequests on all 6 ecmpids!

server

Spoiler

[reader]
label = hdplus02
enable = 1
protocol = internal
device = /dev/sci0
rsakey = BF*********************D5
boxkey = A7********7C
caid = 1843
fix9993 = 0
boxkey = A7xxxxxxxxxxxxxxx7C
detect = cd
mhz = 540
cardmhz = 2700
ident = 1843:000000,003411,008011
group = 1
emmcache = 1,3,2
lb_weight = 100
auprovid = 003411

 

[leyla38]

AW: HD+ bleibt dunkel...

@nando0707 welche oscam rev nutzt du den?


Gesendet von iPhone mit Tapatalk

 

[nando0707]

AW: HD+ bleibt dunkel...

scam.server generated automatically by Streamboard OSCAM 1.20-unstable_svn SVN r10003

 

[leyla38]

Nimm mal den aktuellen rev. Und anschließend mal mhz = 1 versuchen und autospeed = 1

P.S
Bei dir liegt der Fehler das der Karte falsch getaktet ist .: Resync error: readtimeouts ( log )
Gesendet von iPhone mit Tapatalk

 

[motek10]

AW: HD+ bleibt dunkel...

Spoiler

[reader]
label = hdplus02
enable = 1
protocol = internal
device = /dev/sci0
rsakey = BF*********************D5
boxkey = A7********7C
caid = 1843
###fix9993 = 0
###boxkey = A7xxxxxxxxxxxxxxx7C
detect = cd
mhz = 368
cardmhz = 368
###ident = 1843:000000,003411,008011
group = 1
emmcache = 1,3,2
###lb_weight = 100
###auprovid = 003411

 

[leyla38]

@motek10 das geht mit dem alten oscam rev.!

### bis SVN 9099 diese Einstellungen benutzen
#mhz = 369
#cardmhz = 368

Gesendet von iPhone mit Tapatalk

 

[motek10]

AW: HD+ bleibt dunkel...

OSCam r10630

ist das alt?

 

[leyla38]

AW: HD+ bleibt dunkel...

Nein das ist schon aktuell.


Gesendet von iPhone mit Tapatalk

 

[dia]

AW: HD+ bleibt dunkel...

@Link ist nicht mehr aktiv.
mhz 540 stimmt ja auch nicht
höchstens 450

 

[motek10]

AW: HD+ bleibt dunkel...

OSCam r10630

ist das alt?

das war eine rhetorische Frage

und ich habe :
mhz = 368
cardmhz = 368

 

[dia]

AW: HD+ bleibt dunkel...

ja ist alt

 

[4gx35]

AW: HD+ bleibt dunkel...

aktuell: bei autospeed aktiv muss man evtl überhaupt keine cardmhz und mhz mehr angeben, einfach testen

 

[nando0707]

AW: HD+ bleibt dunkel...

Habe Oscam r10660 drauf. Leider zeigt die Karte ERROR an

hier der Log

Spoiler

2015/05/17 00:10:41 0 s >> OSCam << cardserver started, version 1.20-unstable_svn, build r10660 (mipsel-unknown-linux-gnu-ssl-libusb-pcsc)
2015/05/17 00:10:41 0 s (main) System name = Linux
2015/05/17 00:10:41 0 s (main) Host name = dm800se
2015/05/17 00:10:41 0 s (main) Release = 3.2-dm800se
2015/05/17 00:10:41 0 s (main) Version = #1 SMP Fri Jun 6 18:01:34 CEST 2014
2015/05/17 00:10:41 0 s (main) Machine = mips
2015/05/17 00:10:41 0 s (main) Stb model = dm800se
2015/05/17 00:10:41 0 s (main) creating pidfile /tmp/.oscam/oscam.pid with pid 1711
2015/05/17 00:10:41 0 s (config) services reloaded: 0 services freed, 20 services loaded, rejected 0
2015/05/17 00:10:41 0 s (config) userdb reloaded: 11 accounts loaded, 0 expired, 0 disabled
2015/05/17 00:10:41 0 s (main) signal handling initialized
2015/05/17 00:10:41 0 s (config) 662 service-id's loaded in 13 ms
2015/05/17 00:10:41 0 s (config) 148 tier-id's loaded
2015/05/17 00:10:41 0 s (config) 4 provid's loaded
2015/05/17 00:10:41 0 s (net) monitor: initialized (fd=5, port=988)
2015/05/17 00:10:41 0 s (net) cccam: initialized (fd=6, port=12000)
2015/05/17 00:10:41 0 s (reader) hdplus02 [internal] creating thread for device /dev/sci0
2015/05/17 00:10:41 0 s (stat) loadbalancer: can't read from file /tmp/.oscam/stat
2015/05/17 00:10:41 0 s (main) waiting for local card init
2015/05/17 00:10:41 76C00588 r (reader) hdplus02 [internal] Reader initialized (device=/dev/sci0, detect=cd, pll max=27.00 MHz, wanted mhz=5.40 MHz)
2015/05/17 00:10:41 76C00588 r (reader) hdplus02 [internal] Reader sci internal, detected box type: dm800se
2015/05/17 00:10:41 A3C2B8 h (webif) webif: decompressed 160180 bytes back into 384088 bytes
2015/05/17 00:10:41 A3C2B8 h (webif) HTTP Server running. ip=0.0.0.0 port=17000
2015/05/17 00:10:42 76C00588 r (reader) hdplus02 [internal] card detected
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] Calculated work ETU is 5.93 us reader mhz = 540
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] Buffers readed 0 bytes total time_us 75193
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] PLL Reader: ATR Fsmax is 5 MHz, clocking card to 5.40 Mhz (nearest possible mhz specified reader->mhz)
2015/05/17 00:10:44 76C00588 r (reader) hdplus02 [internal] Card responded ok for ifsd request of 160
2015/05/17 00:10:45 76C00588 r (reader) hdplus02 [internal] detect native nagra card
2015/05/17 00:10:47 76C00588 r (reader) hdplus02 [internal] Resync error: readtimeouts 0/0 (max/min) us, writetimeouts 0/0 (max/min) us
2015/05/17 00:10:49 76C00588 r (reader) hdplus02 [internal] T1 Resync command error, trying to reactivate!
2015/05/17 00:10:50 76C00588 r (reader) hdplus02 [internal] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 38 30 20 4D 65 72 30 30 30 28
2015/05/17 00:10:50 76C00588 r (reader) hdplus02 [internal] Init card protocol T1, FI=9, F=512, D=16, N=255
2015/05/17 00:10:50 76C00588 r (reader) hdplus02 [internal] Calculated work ETU is 5.93 us reader mhz = 540
2015/05/17 00:10:50 76C00588 r (reader) hdplus02 [internal] Buffers readed 0 bytes total time_us 75209​

die Configs sind

conf

Spoiler

#---Oscam Config Creator---


[global
logfile = /etc/tuxbox/config
nice = -1
maxlogsize = 1500
preferlocalcards = 2
emmlogdir = /var/log/




[cccam]
port = 12000
nodeid = 8325A4AC10141450
version = 2.3.0
reshare = 1
stealth = 1




[dvbapi]
enabled = 1
au = 1
#delayer = 1
user = local
boxtype = dreambox


[monitor]
port = 988
aulow = 120
monlevel = 1
hideclient_to = 15


[webif]
httpport = 17000
httpuser = oscam
httppwd = oscam
httprefresh = 10
httpshowmeminfo = 1
httpshowuserinfo = 1
httpshowcacheexinfo = 1
httpshowecminfo = 1
httpshowloadinfo = 1
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
aulow = 120
hideclient_to = 15
http_status_log = 1

User

Spoiler

[account]
user = local
au = 1
group = 1,2


[account]
user = Wohn
pwd = ich
group = 1,2,3,4
uniq = 3
monlevel = 2

server

Spoiler

[reader]
label = hdplus02
protocol = internal
device = /dev/sci0
services = hdplus
lb_whitelist_services = hdplus
caid = 1843
detect = cd
autospeed = 1
mhz = 540
cardmhz = 2700
ident = 1843:000000,003411,008011
group = 1
emmcache = 1,3,2,0
auprovid = 003411

dvbapi

Spoiler

P: 1843
#P: 09C4
I: 0

 

[leyla38]

AW: HD+ bleibt dunkel...

Mach mal wie der @4gx35 Post 103 gepostet hat.


Gesendet von iPhone mit Tapatalk