HD+ auf einmal Dunkel

[flowershopowner]

Hi,

ich habe oscam 1.0.0 und CCcam 2.2.1 am Laufen. Bis Freitag ging alles. OScam für HD+ und CCcam direkt mit der Sky Karte. Auf einmal ist HD+ dunkel. Ich dachte, die Konfig wäre falsch oder nicht mehr auf dem aktuellen Stand und habe ein wenig rumgespielt. Jetzt kriege ich:

2011/12/11 20:58:49 2CD514B0 c user (1830&003411/EF11/92:0B2B): not found (0 ms) (of 1 avail 1) - VOX HD

und Äquivalentes für alle anderen HD+ Kanäle. Schaut irgendwie nicht gut aus. Ich dachte auch, dass die Karte abgelaufen wäre aber

->detect native nagra card
-----------------------------------------
|id |tier |valid from |valid to |
+----+--------+------------+------------+
|8011|0064 |2010/01/07 |2011/01/08 |
|8011|0065 |1992/01/01 |1993/01/01 |
|8011|0BEA |2011/01/07 |2012/11/21 |
-----------------------------------------
ROM: D N A S P 1 4 2
REV: R e v G C 6
SER: xxx
CAID: 1830
Prv.ID: 00 00 34 11 (sysid)
Prv.ID: 00 00 00 00
Prv.ID: 00 00 80 11

spricht ja nicht dafür. Wo übersehe ich etwas? Auch nur mit scam oder CCCam kriege ich die Karte nicht ans Laufen. Fehlte da ein AU? Wenn ja, wie komme ich da wieder dran?

Inzwischen scheint sich CCCam sauber mit AU zu verbinden:

2011/12/11 20:58:23 2CD514B0 c client connected to 34000 port
2011/12/11 20:58:23 2CD514B0 c encrypted newcamd:34000-client 127.0.0.1 granted (user, au=hdplussat)
2011/12/11 20:58:23 2CD514B0 c user user authenticated successfully (CCcam)
2011/12/11 20:58:23 2CD514B0 c AU enabled for user user on reader hdplussat

Vor meiner Konfig-Änderung war da ein "AU disabled for user" o.ä. (aus der Erinnerung).

Wäre für JEDE Hilfe sehr dankbar.


LG,
JP

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

Mit cccam wirst du du deine HD+ Karte auch nicht mehr ans laufen bekommen.Mit oscam only auch nicht.Das mußte ich auch gerade erfahren.Was hilft ist mgcamd 1.37 dieser schickt dir auch die emm´s
an oscam.

gruß
Snake

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Hmm. Gut, erster Versuch, aber

2011/12/11 22:01:18 2D4FF4B0 c client connected to 34000 port
2011/12/11 22:01:18 2D4FF4B0 c encrypted newcamd:34000-client 127.0.0.1 granted (user, au=hdplussat)
2011/12/11 22:01:18 2D4FF4B0 c user user authenticated successfully (mgcamd)
2011/12/11 22:01:18 2D4FF4B0 c AU wont be used on this port -> disable AU
2011/12/11 22:02:43 2D4FF4B0 c user (1830&003411/EF10/92:75B9): rejected user ident (121 ms) (of 0 avail 0) - 1830:EF10 unknown (no card support 1830:003411)
2011/12/11 22:02:44 2D4FF4B0 c user (1830&003411/EF10/92:75B9): rejected user ident (121 ms) (of 0 avail 0) - 1830:EF10 unknown (no card support 1830:003411)

Hmmm. Gut, Konfig ein wenig geändert:

2011/12/11 22:04:33 2D4FF4B0 c client connected to 34000 port
2011/12/11 22:04:33 2D4FF4B0 c encrypted newcamd:34000-client 127.0.0.1 granted (user, au=hdplussat)
2011/12/11 22:04:33 2D4FF4B0 c user user authenticated successfully (CCcam)
2011/12/11 22:04:33 2D4FF4B0 c AU enabled for user user on reader hdplussat
2011/12/11 22:06:39 2CCFF4B0 c user (1830&003411/EF10/92:7686): not found (0 ms) (of 1 avail 1) - RTL HD
2011/12/11 22:06:44 2CCFF4B0 c user (1830&003411/EF10/92:06AB): not found (0 ms) (of 1 avail 1) - RTL HD

Das user not found macht mir halt auch irgendwie Sorgen. Mal abgesehen davon, dass die Konfig so noch nicht mit meiner Sky-Karte funktioniert, vermutlich, weil ich OSCam auch erst mal tweaken muss, so dass Sky geht, oder?

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

not found bedeutet das es keinen gültigen key gibt.Mit cccam wird eine wiederbelebung nicht funktionieren installiere Mgcamd

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Das ist jetzt mit mgcamd. Sky läuft auch wieder. HD+ noch nicht. EMMs scheinen geschickt zu werden:

[mg0] bad irdeto chid 0015 max 0
[newcamd] EMM-G (0x1003) -> 127.0.0.1:34000
[newcamd] EMM answer from 127.0.0.1:34000, 3:82

34000 ist der Port für hdplus. Dennoch sagt mir oscam nur timeout oder not found:

2011/12/11 22:29:23 2DD514B0 c encrypted newcamd:34000-client 127.0.0.1 granted (user, au=hdplussat)
2011/12/11 22:29:23 2DD514B0 c user user authenticated successfully (mgcamd)
2011/12/11 22:29:23 2DD514B0 c AU enabled for user user on reader hdplussat
2011/12/11 22:29:23 2D5514B0 c encrypted newcamd:34001-client 127.0.0.1 granted (usersky, au=skysat)
2011/12/11 22:29:23 2D5514B0 c user usersky authenticated successfully (mgcamd)
2011/12/11 22:29:23 2D5514B0 c AU enabled for user usersky on reader skysat
2011/12/11 22:29:25 2DD514B0 c user (1830&003411/EF10/92:1DB9): not found (0 ms)


Dauerts jetzt nur ewig, bis meine Freischaltung vorbeifliegt oder sollte es quasi sofort funktionieren? Gibts bei HDPlus eine Möglichkeit der Reaktivierung, sprich sofortiges Schicken des Keys? Habe da nichts gefunden.

Und btw: Many thanks für Deine Hilfe.

Ist das jetzt eine ganz neue Entwicklung? Ich habe in anderen Boards bisher noch nichts dazu gefunden.

LG

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

mit configs ist es glaube ich leichter.kannst die mal posten.
bei newcamd brauchst du fur sky und hdplus jeweils ein port und einen user.
also hdplus 34000 und sky 340001 und einen user sky und einen für hdplus

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Klar. Welche brauchst Du? PM oder hier? Wie ist hier die aktuelle "Posting-Regel"? Sprich muss ich etwas beachten, damit ich keinen auf den Deckel bekomme?

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Ich probiere es mal:

oscam.server

Spoiler

[reader] label = hdplussat
enable = 1
protocol = internal
device = /dev/sci0
services = hdplus
caid = 1830
rsakey = XXX
boxkey = XXX
detect = cd
mhz = 368
cardmhz = 368
ident = 1830:000000,003411,008011
group = 1
emmcache = 1,3,15
ecmcache = 1
lb_weight = 100


[reader]
detect = CD
device = /dev/sci1
protocol = internal
label = skysat
emmcache = 1,3,2
caid = 1702
ident = 1702:000000
services = sky
group = 2

oscam.services:

Spoiler

[hdplus]caid = 1830
provid = 000000,003411,008011
srvid = EF10,EF11,EF14,EF15,EF74,EF75,EF76,EF77,5273,5274,1519
#srvid = 277E,EF10,EF11,EF14,EF15,EF74,EF75,EF76,EF77


[sky]
caid=1702
provid=000000
srvid=000C,000D,000E,000F,0010,0013,0015,0016,0017,0018,001A,001B,001C,001D,0022,0024,002A,0032,0034,00A8,0206,003C,003D,003E,003F,0040,0041,0042,0043,0044,07FF,2EFE,3331,3394,4461,4462,6FF1,7009,700A,0011,0035,00DD,00DE,00FD,0107,0111,011B,012F,0125,0139,0143,014D,016B,0175,006A,006B,006F,0070,0071,0072,0075,0077,0081,0082,0083,0084,00DF,00FC,0106,0110,011A,0124,012E,0138,0142,014C,0156,0160,0008,0009,0014,0019,0029,000A,000B,002B,0203,0204,0096,0097,0098,0099,009A,009B,009C

oscam.user:

Spoiler

[account] user = user
pwd = pass
disabled = 0
expdate =
group = 1
hostname =
uniq = 0
sleep = 0
monlevel = 2
au = hdplussat
services = hdplus
caid = 1830
betatunnel =
ident = 1830:000000,003411,008011
keepalive = 1
numusers = 0
penalty = 0




[account]
user = usersky
pwd = passsky
group = 2
au = skysat
betatunnel = 1833.007a:1702,1833.007b:1702,1833.007c:1702,1833.007e:1702,1833.007f:1702,1833.0080:1702,1833.0081:1702,1833.0082:1702,1833.0083:1702,1833.0084
ident = 1702:000000
caid = 1702
services = sky

oscam.provid:

Spoiler

1830:008011|HD+ Deutschland|Astra 19.2E|Deutsch 1830:003411|HD+ Deutschland|Astra 19.2E|Deutsch
1830:000000|HD+ Deutschland|Astra 19.2E|Deutsch

oscam.srvid:

Spoiler

# # Astra HD+
#


1843:EF10|Astra HD+|RTL HD|TV|
1843:EF11|Astra HD+|VOX HD|TV|
1843:EF14|Astra HD+|Sport1 HD|TV|
1843:EF15|Astra HD+|RTL 2 HD|TV|
1843:277E|Astra HD+|. (SD)|TV|
1843:EF74|Astra HD+|Sat.1 HD|TV|
1843:EF75|Astra HD+|PRO7 HD|TV|
1843:EF76|Astra HD+|kabel eins HD|TV|
1843:EF77|Astra HD+|Sixx HD|TV|


1830:EF10|Astra HD+|RTL HD|TV|
1830:EF11|Astra HD+|VOX HD|TV|
1830:EF14|Astra HD+|Sport1 HD|TV|
1830:EF15|Astra HD+|RTL 2 HD|TV|
1830:277E|Astra HD+|. (SD)|TV|
1830:EF74|Astra HD+|Sat.1 HD|TV|
1830:EF75|Astra HD+|PRO7 HD|TV|
1830:EF76|Astra HD+|kabel eins HD|TV|
1830:EF77|Astra HD+|Sixx HD|TV|

newcamd.conf:

Spoiler

# /var/tuxbox/config/newcamd.conf#
# this is the configfile for MGCamd with NewCS!!!!
#
#
# What Demux API is used? (1 = very old, 2 = rel (Dreambox), 3 = head (VDR))
DEMUX_API = 2
# on PPC version: What Box is used? Valid options are DBOX2, DM7000 and DM5600
# on I386 version this parameter is ignored
BOX_TYPE = DM8000
# Which device for writing control words should be used?
# Valid options are CA, SDEV or GTX
# (SDEV and GTX = /proc/bus/gtx, CA = /dev/caX or /dev/dvb/card0/caX)
CONTROL_WORD_DEVICE = CA
# What CA0 API is used?
# 3 for recent DVB-S driver or recent Dreambox drivers (dream.o from 1.07.3)
# also for ca1 use on dbox2
# 2 for older Dreambox driver (ca.o or dream.o up to 1.07.2)
# no effect on PPC version if CONTROL_WORD_DEVICE = GTX or SDEV
CA_API = 3
# output control words to /proc/bus/gtx in 16 byte or 4096 byte packets
# no effect on I386 version or on PPC version, if BOX_TYPE = DREAMBOX
GTX_OUTPUT_MODE = 16
# This is important for channels which frequently change between free and
# encrypted broadcasts. The change will be reflected in the PMT. If you
# don't want your picture to stop when the channel goes from free access
# mode to encrypted mode, either your zapper (zapit/Enigma) or newcamd
# itself has to keep track of PMT changes. Recent Enigma versions do this,
# so you can set PMT_UPDATE_WATCH to no. Recent Zapit versions also have
# this option, but it is not compiled by default. So when using Zapit
# without PMT updates, you need to enable newcamd to monitor the PMT
# (PMT_UPDATE_WATCH = yes). Having both zapper and newcamd monitor
# the PMT at the same time, can lead to all kind of instabilities and
# should therefore by avoided, even if it seems to work at first.
PMT_UPDATE_WATCH = yes
# Use emulator?
EMU = yes
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = yes
# deactivates the dbox2 Betacrypt CAM
# this has to be set to yes on Dreambox
DISABLE_CAM = yes
# use dbox2 Betacrypt CAM for caids 06, 17 or both (00)?
CAM_CASYS = 17
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are Betacrypt UDS control word server
# connected to newcamd
AU = yes
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = no
# On Screen Display, neutrino, enigma or none
OSD = none
# Recent Enigma versions come with a new option "Use http authentication"
# in the Expert Setup menu. If this option is enabled, the Enigma web server
# requires all clients to authorize themselves with username (root) and
# password (usually dbox2 or dreambox). The following option tells newcamd
# about the authentication username and password to use for the web server
# in order to be able to display its on screen information.
OSD_WEB_LOGIN = root:dreambox
# print debug messages about ECM handling
DEBUG_ECM = yes
# print debug messages about EMM handling
DEBUG_EMM = yes
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = yes
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = yes
# print command message to/from dbox2 CAM as hex strings
DEBUG_CAM_HEX = no
# print all plain control words used
SHOW_CW = no
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = yes
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
# delay between channel zap and appearance of the OSD
OSD_WAIT_TIME = 2000
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 500
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = no
# write osd ca info to file
# CA_INFO_FILE = /tmp/cainfo.txt
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name>
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# hostname = uds to use betad, port is the serial port in that case
#
#CWS = uds 1 premiere premiere
#CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv
#CWS = 127.0.0.1 10110 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 34000 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 34001 usersky passsky 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 20
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 12000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Kleiner Nachtrag. Wenn ich mir die Status-Seite des oscam Webservers ansehe, dann steht bei der hdplus karte als Status "ERROR" und AU=0. Bei der Sky Karte hingegen CARDOK und AU=-2. Nur, falls das hilft...

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

hast du ne hd01?

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Weiße Karte (vermute das meinst Du).

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

Error nix gut

nimm mal die einstellungen.alles andere von hdplussat wech


[reader]
label = hdplussat
protocol = internal
device = /dev/sci0
showcls = 0
caid = 1830
rsakey = xxxxx
boxkey =xxxxx
detect = cd
mhz = 357
cardmhz = 357
group = 1
emmcache = 1,3,2

 

[Snakebitez]

AW: HD+ auf einmal Dunkel

bei deinem user auch dur das ersetzen

[account]
user = user
pwd = pass
disabled = 0
group = 1
uniq = 0
sleep = 0
monlevel = 2
au = hdplussat
caid = 1830
keepalive = 1

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Hi. Nimm mal den RSA/Boxkey raus. Habe ich eben auch. Sorry for that.

Abgesehen davon: Done. Bisher keine Änderung (ja, ich habe den oscam restarted).

2011/12/11 23:13:07 2D4FF4B0 c user (1830&003411/EF10/92:6E57): not found (1 ms) (of 1 avail 1) - RTL HD
2011/12/11 23:13:14 2D4FF4B0 c user (1830&003411/EF10/92:6E57): timeout (5005 ms) (of 0 avail 0) - RTL HD

Startup vom oscam:
root@dm8000:/etc/tuxbox/config# oscam_1.00
Warning: keyword 'clientdyndns' in global section not recognized
Warning: keyword 'resolvedelay' in global section not recognized
2011/12/11 23:12:57 2AAC6850 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4574 (mips-tuxbox-linux)
2011/12/11 23:12:57 2AAC6850 s version=1.00-unstable_svn, build #4574, system=mips-tuxbox-linux, nice=-1
2011/12/11 23:12:57 2AAC6850 s client max. idle=120 sec, debug level=0
2011/12/11 23:12:57 2AAC6850 s max. logsize=10 Kb
2011/12/11 23:12:57 2AAC6850 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=120 ms
2011/12/11 23:12:57 2AAC6850 s auth size=4976
2011/12/11 23:12:57 2AAC6850 s services reloaded: 0 services freed, 2 services loaded
2011/12/11 23:12:57 2AAC6850 s userdb reloaded: 2 accounts loaded, 0 expired, 0 disabled
2011/12/11 23:12:57 2AAC6850 s signal handling initialized (type=sysv)
2011/12/11 23:12:57 2AAC6850 s 18 service-id's loaded
2011/12/11 23:12:57 2AAC6850 s can't open file "/var/tuxbox/config/oscam.tiers" (err=2), no tier-id's loaded
2011/12/11 23:12:57 2AAC6850 s 3 provid's loaded
2011/12/11 23:12:57 2AAC6850 s can't open file "/var/tuxbox/config/oscam.ird" (errno=2) irdeto guessing not loaded
2011/12/11 23:12:57 2AAC6850 s monitor: disabled
2011/12/11 23:12:57 2AAC6850 s camd33: disabled
2011/12/11 23:12:57 2AAC6850 s camd35: disabled
2011/12/11 23:12:57 2AAC6850 s cs378x: disabled
2011/12/11 23:12:57 2AAC6850 s newcamd: initialized (fd=6, port=34000, crypted)
2011/12/11 23:12:57 2AAC6850 s CAID: 1830
2011/12/11 23:12:57 2AAC6850 s provid #0: 003411
2011/12/11 23:12:57 2AAC6850 s provid #1: 000000
2011/12/11 23:12:57 2AAC6850 s provid #2: 008011
2011/12/11 23:12:57 2AAC6850 s newcamd: initialized (fd=7, port=34001, crypted)
2011/12/11 23:12:57 2AAC6850 s CAID: 1702
2011/12/11 23:12:57 2AAC6850 s provid #0: 000000
2011/12/11 23:12:57 2AAC6850 s cccam: disabled
2011/12/11 23:12:57 2AAC6850 s radegast: disabled
2011/12/11 23:12:57 2AAC6850 s http thread started
2011/12/11 23:12:57 2BCFF4B0 h HTTP Server listening on port 83
2011/12/11 23:12:57 2AAC6850 s creating thread for device /dev/sci0
2011/12/11 23:12:57 2AAC6850 s creating thread for device /dev/sci1
2011/12/11 23:12:57 2AAC6850 s loadbalancer: can't read from file /tmp/.oscam/stat
2011/12/11 23:12:57 2AAC6850 s waiting for local card init
2011/12/11 23:12:57 2C4FF4B0 r reader thread started (thread=2C4FF4B0, label=hdplussat, device=/dev/sci0, detect=cd, mhz=357, cardmhz=357)
2011/12/11 23:12:57 2CCFF4B0 r reader thread started (thread=2CCFF4B0, label=skysat, device=/dev/sci1, detect=cd, mhz=357, cardmhz=357)
2011/12/11 23:12:57 2C4FF4B0 r hdplussat card detected
2011/12/11 23:12:57 2CCFF4B0 r skysat card detected
2011/12/11 23:12:58 2C4FF4B0 r ERROR: 0 characters found in ATR
2011/12/11 23:12:58 2C4FF4B0 r Error activating card.
2011/12/11 23:12:59 2CCFF4B0 r ATR: 3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 03 84 55 FF 80 6D
2011/12/11 23:13:00 2C4FF4B0 r ERROR: 0 characters found in ATR
2011/12/11 23:13:00 2C4FF4B0 r Error activating card.
2011/12/11 23:13:00 2CCFF4B0 r Maximum frequency for this card is formally 6 Mhz, clocking it to 6.00 Mhz
2011/12/11 23:13:01 2C4FF4B0 r ERROR: 0 characters found in ATR
2011/12/11 23:13:01 2C4FF4B0 r Error activating card.
2011/12/11 23:13:01 2CCFF4B0 r detect irdeto tunneled nagra card
2011/12/11 23:13:01 2CCFF4B0 r no rsa key configured -> using irdeto mode
2011/12/11 23:13:01 2CCFF4B0 r detect irdeto card
2011/12/11 23:13:01 2CCFF4B0 r caid: 1702, acs: 3.84, country code: GER
2011/12/11 23:13:02 2CCFF4B0 r providers: 4, ascii serial: 0276499612, hex serial: 7B0C9C, hex base: 1A
2011/12/11 23:13:02 2C4FF4B0 r card initializing error
2011/12/11 23:13:04 2CCFF4B0 r WARNING: For Irdeto cards you will have to set 'cardmhz = 600' in oscam.server
2011/12/11 23:13:05 2CCFF4B0 r active providers: 2 (000000,000000)
2011/12/11 23:13:05 2CCFF4B0 r found cardsystem
2011/12/11 23:13:05 2CCFF4B0 r entitlements for provider: 2, id: 000000
2011/12/11 23:13:05 2CCFF4B0 r chid: 00F0, date: 2010/10/15 - 2011/06/26
2011/12/11 23:13:05 2CCFF4B0 r chid: 05E7, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 0276, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 04CE, date: 2010/10/15 - 2011/06/26
2011/12/11 23:13:05 2CCFF4B0 r chid: 0605, date: 2010/10/15 - 2011/06/26
2011/12/11 23:13:05 2CCFF4B0 r chid: 7D27, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 05E8, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 05DD, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 05DE, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 000F, date: 2009/03/01 - 2009/11/10
2011/12/11 23:13:05 2CCFF4B0 r chid: 05FB, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 029D, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:05 2CCFF4B0 r chid: 05DF, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 05F1, date: 2009/10/13 - 2010/06/24
2011/12/11 23:13:05 2CCFF4B0 r chid: 0102, date: 2008/11/09 - 2008/11/25
2011/12/11 23:13:05 2CCFF4B0 r chid: 028B, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:05 2CCFF4B0 r chid: 028C, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:05 2CCFF4B0 r chid: 028D, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:05 2CCFF4B0 r chid: 028E, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:05 2CCFF4B0 r chid: 028F, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0290, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 029E, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0291, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0292, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0293, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0294, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0295, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0298, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0299, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 029A, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 029B, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 029C, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0103, date: 2008/11/09 - 2008/11/25
2011/12/11 23:13:06 2CCFF4B0 r chid: 029C, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0104, date: 2008/11/09 - 2008/11/25
2011/12/11 23:13:06 2CCFF4B0 r chid: 0406, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r chid: 0105, date: 2008/11/09 - 2008/11/25
2011/12/11 23:13:06 2CCFF4B0 r chid: 0004, date: 2008/01/19 - 2008/01/21
2011/12/11 23:13:06 2CCFF4B0 r [irdeto-reader] ready for requests
2011/12/11 23:13:06 2AAC6850 s init for all local cards done
2011/12/11 23:13:06 2AAC6850 s anti cascading disabled
2011/12/11 23:13:06 2D4FF4B0 c client connected to 34000 port
2011/12/11 23:13:06 2DCFF4B0 c client connected to 34001 port
2011/12/11 23:13:06 2D4FF4B0 c encrypted newcamd:34000-client 127.0.0.1 granted (user, au=hdplussat)
2011/12/11 23:13:06 2D4FF4B0 c user user authenticated successfully (mgcamd)
2011/12/11 23:13:06 2D4FF4B0 c AU wont be used on this port -> disable AU
2011/12/11 23:13:06 2DCFF4B0 c encrypted newcamd:34001-client 127.0.0.1 granted (usersky, au=skysat)
2011/12/11 23:13:06 2DCFF4B0 c user usersky authenticated successfully (mgcamd)
2011/12/11 23:13:06 2DCFF4B0 c AU enabled for user usersky on reader skysat
2011/12/11 23:13:07 2D4FF4B0 c user (1830&003411/EF10/92:6E57): not found (1 ms) (of 1 avail 1) - RTL HD
2011/12/11 23:13:14 2D4FF4B0 c user (1830&003411/EF10/92:6E57): timeout (5005 ms) (of 0 avail 0) - RTL HD


Nach Deinen Änderungen steht da jetzt auch "AU wont be used on this port"... Das war vorher anders...

 

[flowershopowner]

AW: HD+ auf einmal Dunkel

Sodele. Ich bin weiter... Karte mal gezogen und neu gesteckt. Dann kam "Boxkey" falsch, da im Cut&Paste von Dir Leerzeichen reingerutscht waren. Auf alle Fälle ist der Kartenstatus nun CARDOK. ATR wird beim Starten angezeigt. Allerdings:

2011/12/11 23:18:55 2C4FF4B0 r WARNING: For NAGRA2 cards you will have to set 'cardmhz = 368' in oscam.server
2011/12/11 23:18:55 2C4FF4B0 r found cardsystem

Aber auch mit cardmhz=368 sehe ich keine Änderung.

2011/12/11 23:23:01 2D5FF4B0 c user (1830&003411/EF10/92:142C): not found (232 ms) (of 1 avail 1) - RTL HD
2011/12/11 23:23:02 2D5FF4B0 c user (1830&003411/EF10/926F8): timeout (5005 ms) (of 0 avail 0) - RTL HD

AU habe ich auch wieder an.