Hi danke erstmal für die Antwort.
Geladen hier von dealirio Vers8.0 letzte.
Einzelplatz??keine Ahnung was das heißt
Virtuelle Maschine nein
Loader der mitgelieferte.
Update gemacht Audi aber die sind noch im Update Ordner vom herunterladen.wenn ich die anklicke passiert nichts.
Win 10
Mfg
sowohl 32 und 64 bit gehen, aber 64 ist meiner Meinung nach komplizierter zu installieren. Aber es ist ja eine Install in de Download von @dealirio was dazu beachtet werden muss. Strikt daran halten. ich habe es auch zweimal versuche mussen.
Hier nochmal für WINDOWS 10 x 64 bits den AUSSCHNITT aus @dealirio s Beitrag
Code:
Installing under Windows 7,8,10 x64
1. The installation is similar to the one for Windows XP x32 with the exception
of the Hardlock and the Multikey which are located in the x64 folder along with
the corresponding instructions.
Also, downloaden, und dann alles einmal entpackt im Laufwerk c:/ plazieren, dann von dort aus die .exe ausführen und den Rest wie in der Anleitung.
LG
Frohes neues Jahr erstmal. Habe jetzt alles versucht läuft soweit. holt sich Updates und fängt an zu installieren .wenn erstes Update bis zum Schluss durchläuft kommt das .ich denke ist ein Windows Problem.
Welchen HARDLOCK hast du den genommen?
Und welchen Loader zur Install?
Du musst Regestriert sein, um das angehängte Bild zusehen.
Und ausserdem ist in dem DOWNLOAD von @dealirio ja auch noch dieses für die Install bei Windows 10 x64!
Code:
1. Execute the following commands from the command prompt with full administrative rights:
bcdedit.exe /set nointegritychecks ON
bcdedit.exe /set TESTSIGNING ON
Each command should receive a successeful execution confirmation.
2. Reboot the computer while holding the "Shift" key.
3. In the subsequently opening screens: Choose an option ->> Troubleshoot ->> Reset this PC ->> Startup settings ->> Restart to change Windows options such as ->> Restart
4. After Windows restarts chose option 7) Disable driver signature enforcement.
5. Edit the registry by running "0000750A.reg" from the "MULTIKEY64" folder.
6. Run "INSTALL.CMD" from the "MULTIKEY64" folder. Lack of error messages would indicate successefull driver installation.
7. Run "hardlock.EXE" from the "Hardlock" folder.
8. Reboot the computer.
Should you run into problems deleting the earlier instance of the multikey driver:
1. Run "REMOVE.CMD" from the "MULTIKEY64" folder. Lack of error messages would indicate successefull driver deletion.
2. Run the "infclean64.exe" utility from the "infclean05" folder for the final clean-up.
You can turn off the test mode but in this case you will need to disable Driver Signature Enforcement.
You can get rid of the "Test Mode" watermark by running "RemoveWatermark 7 X64.exe".
Should you run into problems in the step 6 above please follow the advice provided by andy040670:
6. Start the Device Manager => right click the root directory => pick "Add
legacy hardware" => "Next" => "Install the hardware that I manually select from
a list (Advanced)" => "Next" (don't pick anything) => "Have Disk..." => point to
the MULTIKEY64 folder => OK => agree to install the non-signed driver.
An advice from aprimerov:
If executing the "bcdedit.exe /set nointegritychecks ON bcdedit.exe /set TESTSIGNING ON" command causes an error you should disable the "Secure Boot" in BIOS.
A huge "thank you" for the working x64 Multikey goes to http://testprotect.com.
Sincerely,
andyl
Anhänge
Du musst angemeldet sein, um die Anhangsliste zu sehen.
@josef_31 ich habe die von dir hochgeladen etka Version runtergeladen!
Leider bekomme ich sie nicht ans laufen auch einem 64 bit System !
den ordner install kann ich nicht entpacken da mir das passende Passwort fehlt !