Mutant HD1265 bleibt im Boot Hängen!

[TheHAcker20052]

Hallo Zusammen,

ich stehe gerade vor ein Problem, ich habe eine Mutant HD1265 bekommen, welche im boot hängt.

Jeglicher Versuch die Box zu flashen scheitert, da der USB Stick nicht erkannt wird.

Ich denke es wurde ein falsches image eingespielt.

Kann mir da jemand ein Tipp geben, wie ich sie wieder ins leben zurück holen kann ?

Hier das Bootlog :

Spoiler

BCM07362500

M0CZS
L2=1
LLMB=1
BrCfg=E30FB7C6
#@

BCM90736A0 CFE v14.2, Endian Mode: Little
Build Date: 2015-09-03 (v39)
Copyright (C) Broadcom Corporation.

Enabling NAND flash at CS2: TC58NVG1(DEVICE ID=0x98DA9015), ECC Level=8, Spare Area Size=32
MACRONIX SPI flash detected: Size = 4MB, Sector Size 4096, Page Size 256

CPU speed: 751MHz
DDR Frequency: 796 MHz
DDR Mode: DDR3
Total memory(MEMC 0): 512MB
MEMC 0 DDR Width: 16
Boot Device: SPI
Total flash: 4MB
RTS VERSION: Initial RTS Version
ETH0_PHY: INT
ETH0_MDIO_MODE: 1
ETH0_SPEED: 100
ETH0_PHYADDR: 1

Initializing USB.

CFE initialized.
Starting splash screen.
Found splash image - Width = 720 Height = 576
USB: New full speed device connected to bus 1 hub 1 port 2
Driver not found.

Loader:elf Filesys:raw Dev:flash0.kernel File: Optionsnull)
Loading: Failed.
Could not load : I/O error
Trying again with '-nz' option
Loading: Failed.
Could not load : I/O error
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Optionsnull)
Loading: 0x80001000/9681168 0x8093c910/154464 Entry address is 0x80735d60
Starting program at 0x80735d60

Initializing cgroup subsys cpuset
Linux version 4.0.1 (oe1@build4) (gcc version 5.3.0 (GCC) ) #1 SMP Sat Jul 9 17:28:13 CEST 2016
Fetching vars from bootloader... found 11 vars.
Options: moca=0 sata=1 pcie=0 usb=1
Using 512 MB + 0 MB RAM (from CFE)
CPU0 revision is: 0002a065 (Broadcom BMIPS4380)
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
memory: 10000000 @ 20000000 (usable)
bmem: adding 192 MB RESERVED region at 64 MB (0x0c000000@0x04000000)
Zone ranges:
Normal [mem 0x0000000000000000-0x000000002fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x0000000000000000-0x000000000fffffff]
node 0: [mem 0x0000000020000000-0x000000002fffffff]
Initmem setup node 0 [mem 0x0000000000000000-0x000000002fffffff]
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
PERCPU: Embedded 10 pages/cpu @81487000 s10512 r8192 d22256 u40960
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129920
Kernel command line: ubi.mtd=rootfs rootfstype=ubifs root=ubi0:rootfs bmem=192M@64M console=ttyS0,115200n8
PID hash table entries: 2048 (order: 1, 8192 bytes)
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 312952K/524288K available (7430K kernel code, 361K rwdata, 1432K rodata, 232K init, 137K bss, 211336K reserved, 0K cma-reserved)
Hierarchical RCU implementation.
NR_IRQS:160
Measuring MIPS counter frequency...
Detected MIPS clock frequency: 751 MHz (375.768 MHz counter)
Console: colour dummy device 80x25
Calibrating delay loop... 749.56 BogoMIPS (lpj=374784)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
Initializing cgroup subsys memory
SMP: Booting CPU1...
Primary instruction cache 32kB, VIPT, 2-way, linesize 64 bytes.
Primary data cache 64kB, 4-way, VIPT, cache aliases, linesize 64 bytes
CPU1 revision is: 0002a065 (Broadcom BMIPS4380)
FPU revision is: 00130001
SMP: CPU1 is running
Brought up 2 CPUs
devtmpfs: initialized
NET: Registered protocol family 16
USB0: power enable is active high; overcurrent is active low
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
Bluetooth: Core ver 2.20
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
cfg80211: Calling CRDA to update world regulatory domain
Switched to clocksource wktmr
FS-Cache: Loaded
NET: Registered protocol family 2
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP: reno registered
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
futex hash table entries: 512 (order: 3, 32768 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.23)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
console [ttyS0] disabled
serial8250.0: ttyS0 at MMIO 0x10406800 (irq = 62, base_baud = 5062500) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x10406840 (irq = 63, base_baud = 5062500) is a 16550A
serial8250.0: ttyS2 at MMIO 0x10406880 (irq = 64, base_baud = 5062500) is a 16550A
loop: module loaded
ahci ahci.0: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
ahci ahci.0: flags: ncq sntf stag clo slum part
scsi host0: ahci
scsi host1: ahci
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 87
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 87
brcmstb_nand: NAND controller driver is loaded
libphy: Fixed MDIO Bus: probed
bcmgenet bcmgenet.0: GENET 2.0 EPHY: 0x00b0
bcmgenet bcmgenet.0: failed to get enet-eee clock
libphy: bcmgenet MII bus: probed
bcmgenet bcmgenet.0: configuring instance for internal PHY
attached PHY at address 1
usbcore: registered new interface driver zd1201
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 66, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 2
ohci-brcm ohci-brcm.0: irq 67, io mem 0x10480400
ata1: SATA link down (SStatus 0 SControl 300)
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
usbcore: registered new interface driver btusb
Driver 'mmcblk' needs updating - please use bus_type methods
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
sdhci-brcmstb sdhci-brcmstb.0: Enabling controller
sdhci-brcmstb sdhci-brcmstb.0: No vmmc regulator found
sdhci-brcmstb sdhci-brcmstb.0: No vqmmc regulator found
mmc0: SDHCI controller on sdhci-brcmstb.0 [sdhci-brcmstb.0] using ADMA
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Bluetooth: HIDP socket layer initialized
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS2: setting up NAND flash (primary)
nand: device found, Manufacturer ID: 0x98, Chip ID: 0xda
nand: Toshiba NAND 256MiB 3,3V 8-bit
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 128
brcmnand brcmnand.0: 256MiB total, 128KiB blocks, 2KiB pages, 32B OOB, 8-bit, BCH-8

Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
nand_read_bbt: bad block at 0x00000c000000
nand_read_bbt: bad block at 0x00000c020000
Creating 3 MTD partitions on "brcmnand.0":
0x000000000000-0x000010000000 : "complete"
0x000000000000-0x000000600000 : "kernel"
0x000000600000-0x000010000000 : "rootfs"
EBI CS0: setting up SPI flash
brcm_setup_spi_flash: can't locate SPI master
brcm_setup_cs: can't register SPI flash (error -19)
ubi0: default fastmap pool size: 100
ubi0: default fastmap WL pool size: 25
ubi0: attaching mtd2
ata2: SATA link down (SStatus 0 SControl 300)
ubi0: attached by fastmap
ubi0: fastmap pool size: 100
ubi0: fastmap WL pool size: 25
ubi0: attached mtd2 (name "rootfs", size 250 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 1994, bad PEBs: 6, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 42/4, WL threshold: 4096, image sequence number: 703849362
ubi0: available PEBs: 0, total reserved PEBs: 1994, PEBs reserved for bad PEB handling: 34
ALSA device list:
ubi0: background thread "ubi_bgt0d" started, PID 63
No soundcards found.
usb 2-2: new full-speed USB device number 2 using ohci-brcm
UBIFS: background thread "ubifs_bgt0_0" started, PID 64
UBIFS: recovery needed
random: nonblocking pool is initialized
UBIFS: recovery completed
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 246714368 bytes (235 MiB, 1943 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 238AD244-E8B1-47E9-A29E-8B84949A8C3F, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:13.
devtmpfs: mounted
Freeing unused kernel memory: 232K (80906000 - 80940000)
INIT: version 2.88 booting
/etc/init.d/rc: line 72: stty: command not found
/etc/rcS.d/S02sysfs.sh: line 17: grep: command not found
/etc/rcS.d/S02volatile-media.sh: line 13: grep: command not found
/etc/rcS.d/S02volatile-media.sh: line 13: grep: command not found
/etc/rcS.d/S04mdev: line 3: grep: command not found
/etc/rcS.d/S04mdev: line 4: grep: command not found
/etc/rcS.d/S04mdev: line 8: rm: command not found
/etc/rcS.d/S04mdev: line 9: mknod: command not found
/etc/rcS.d/S04mdev: line 10: mkdir: command not found
mount: mount point /dev/pts does not exist
/etc/rcS.d/S04mdev: line 19: touch: command not found
/etc/rcS.d/S04mdev: line 23: mdev: command not found
/etc/rcS.d/S04modutils.sh: line 19: uname: command not found
/etc/rcS.d/S04modutils.sh: line 29: cat: command not found
/etc/rcS.d/S04modutils.sh: line 29: cat: command not found
/etc/rcS.d/S04modutils.sh: line 29: cat: command not found
/etc/rcS.d/S05modload.sh: line 6: find: command not found
/etc/rcS.d/S05modload.sh: line 6: grep: command not found
/dev/dvb/adapter0/video0: No such file or directory
/etc/rcS.d/S06checkroot.sh: line 145: ln: command not found
/etc/rcS.d/S06hotplug.sh: line 3: mdev: command not found
/etc/rcS.d/S37populate-volatile.sh: line 12: dirname: command not found
/etc/rcS.d/S37populate-volatile.sh: line 13: sed: command not found
/etc/volatile.cache: line 2: mkdir: command not found
/etc/volatile.cache: line 3: chown: command not found
/etc/volatile.cache: line 4: chmod: command not found
/etc/volatile.cache: line 6: mkdir: command not found
/etc/volatile.cache: line 7: chown: command not found
/etc/volatile.cache: line 8: chmod: command not found
/etc/volatile.cache: line 10: mkdir: command not found
/etc/volatile.cache: line 11: chown: command not found
/etc/volatile.cache: line 12: chmod: command not found
/etc/volatile.cache: line 14: mkdir: command not found
/etc/volatile.cache: line 15: chown: command not found
/etc/volatile.cache: line 16: chmod: command not found
/etc/volatile.cache: line 18: mkdir: command not found
/etc/volatile.cache: line 19: chown: command not found
/etc/volatile.cache: line 20: chmod: command not found
/etc/volatile.cache: line 23: readlink: command not found
/etc/volatile.cache: line 23: readlink: command not found
/etc/volatile.cache: line 37: readlink: command not found
/etc/volatile.cache: line 37: readlink: command not found
/etc/volatile.cache: line 51: readlink: command not found
/etc/volatile.cache: line 51: readlink: command not found
/etc/volatile.cache: line 65: readlink: command not found
/etc/volatile.cache: line 65: readlink: command not found
/etc/volatile.cache: line 79: readlink: command not found
/etc/volatile.cache: line 79: readlink: command not found
/etc/volatile.cache: line 92: mkdir: command not found
/etc/volatile.cache: line 93: chown: command not found
/etc/volatile.cache: line 94: chmod: command not found
/etc/volatile.cache: line 96: touch: command not found
/etc/volatile.cache: line 97: chown: command not found
/etc/volatile.cache: line 98: chmod: command not found
/etc/volatile.cache: line 100: touch: command not found
/etc/volatile.cache: line 101: chown: command not found
/etc/volatile.cache: line 102: chmod: command not found
/etc/volatile.cache: line 104: touch: command not found
/etc/volatile.cache: line 105: chown: command not found
/etc/volatile.cache: line 106: chmod: command not found
/etc/volatile.cache: line 108: touch: command not found
/etc/volatile.cache: line 109: chown: command not found
/etc/volatile.cache: line 110: chmod: command not found
/etc/volatile.cache: line 112: touch: command not found
/etc/volatile.cache: line 113: chown: command not found
/etc/volatile.cache: line 114: chmod: command not found
/etc/volatile.cache: line 116: touch: command not found
/etc/volatile.cache: line 117: chown: command not found
/etc/volatile.cache: line 118: chmod: command not found
/etc/volatile.cache: line 120: mkdir: command not found
/etc/volatile.cache: line 121: chown: command not found
/etc/volatile.cache: line 122: chmod: command not found
/etc/volatile.cache: line 124: mkdir: command not found
/etc/volatile.cache: line 125: chown: command not found
/etc/volatile.cache: line 126: chmod: command not found
/etc/volatile.cache: line 128: mkdir: command not found
/etc/volatile.cache: line 129: chown: command not found
/etc/volatile.cache: line 130: chmod: command not found
/etc/volatile.cache: line 132: mkdir: command not found
/etc/volatile.cache: line 133: chown: command not found
/etc/volatile.cache: line 134: chmod: command not found
/etc/volatile.cache: line 136: mkdir: command not found
/etc/volatile.cache: line 137: chown: command not found
/etc/volatile.cache: line 138: chmod: command not found
/etc/rcS.d/S37populate-volatile.sh: line 231: ln: command not found
/etc/rcS.d/S38devpts.sh: line 13: grep: command not found
/etc/rcS.d/S38dmesg.sh: line 17: /var/log/dmesg: No such file or directory
ALSA: Restoring mixer settings...
/etc/rcS.d/S39hostname.sh: line 10: /bin/hostname: No such file or directory
/etc/rcS.d/S39hostname.sh: line 19: cat: command not found
/etc/rcS.d/S39hostname.sh: line 19: hostname: command not found
/usr/sbin/alsactl: state_lock:125: file /var/lib/alsa/asound.state lock error: No such file or directory
net.ipv4.conf.default.rp_filter = 1
net.ipv4.conf.all.rp_filter = 1
vm.dirty_writeback_centisecs = 300
vm.dirty_background_ratio = 1
vm.min_free_kbytes = 8192
vm.dirty_ratio = 60
/usr/sbin/alsactl: load_state:1683: Cannot open /var/lib/alsa/asound.state for reading: No such file or directory
vm.swappiness = 30

do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 7652d674 in libpthread-2.23.so[76524000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 77115674 in libpthread-2.23.so[7710c000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 7662d674 in libpthread-2.23.so[76624000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 77019674 in libpthread-2.23.so[77010000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 76f71674 in libpthread-2.23.so[76f68000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 76655674 in libpthread-2.23.so[7664c000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 76b41674 in libpthread-2.23.so[76b38000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 769e5674 in libpthread-2.23.so[769dc000+18000]
ra = 004f93cc in enigma2[400000+276000]


do_page_fault(): sending SIGSEGV to enigma2 for invalid read access from 0000001c
epc = 77105674 in libpthread-2.23.so[770fc000+18000]
ra = 004f93cc in enigma2[400000+276000]

 

[Osprey]

Could not load : I/O error

Probiiere einen anderen Stick. Am besten einen nicht größer als 4GB.