1. Diese Seite verwendet Cookies. Wenn du dich weiterhin auf dieser Seite aufhältst, akzeptierst du unseren Einsatz von Cookies. Weitere Informationen

Oscam auf DD-WRT, easymouse 2 wird nicht erkannt

Dieses Thema im Forum "Andere Router Modelle Archiv" wurde erstellt von SR-88, 13. Juli 2013.

  1. SR-88
    Offline

    SR-88 Freak

    Registriert:
    18. April 2012
    Beiträge:
    288
    Zustimmungen:
    67
    Punkte für Erfolge:
    28
    Hey Leute,

    brauche mal eure Unterstützung. Habe DD-WRT auf meinem Asus RT n66u laufen, Oscam ist auch bereits installiert. Jedoch wird die Easymouse nicht erkannt.

    dmesg

    root@unknown:/tmp/home/root# dmesg
    Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #5 Sun Jun 9 19:08:32 CEST 2013
    CPU revision is: 00019749
    Determined physical RAM map:
    memory: 07fff000 @ 00000000 (usable)
    memory: 08000000 @ 87fff000 (usable)
    Entering add_active_range(0, 0, 32767) 0 entries of 256 used
    Entering add_active_range(0, 557055, 589823) 1 entries of 256 used
    Zone PFN ranges:
    Normal 0 -> 131072
    HighMem 131072 -> 589823
    early_node_map[2] active PFN ranges
    0: 0 -> 32767
    0: 557055 -> 589823
    On node 0 totalpages: 65535
    Normal zone: 0 pages used for memmap
    Normal zone: 0 pages reserved
    Normal zone: 32767 pages, LIFO batch:7
    HighMem zone: 0 pages used for memmap
    HighMem zone: 32768 pages, LIFO batch:7
    Built 1 zonelists. Total pages: 65535
    Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
    Primary data cache 32kB, 4-way, linesize 32 bytes.
    Synthesized TLB refill handler (20 instructions).
    Synthesized TLB load handler fastpath (32 instructions).
    Synthesized TLB store handler fastpath (32 instructions).
    Synthesized TLB modify handler fastpath (31 instructions).
    PID hash table entries: 512 (order: 9, 2048 bytes)
    CPU: BCM5300 rev 1 pkg 0 at 600 MHz
    Using 300.000 MHz high precision timer.
    console [ttyS0] enabled
    Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    Memory: 255300k/131068k available (33k kernel code, 6544k reserved, 2949k data, 128k init, 131072k highmem)
    Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
    Mount-cache hash table entries: 512
    NET: Registered protocol family 16
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    PCI: Initializing host
    PCI: Reset RC
    PCI: Initializing host
    PCI: Reset RC
    PCI: Fixing up bus 0
    PCI/PCIe coreunit 0 is set to bus 1.
    PCI: Fixing up bridge
    PCI: Setting latency timer of device 0000:01:00.0 to 64
    PCI: Fixing up bridge
    PCI: Setting latency timer of device 0000:01:00.1 to 64
    PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
    PCI: Fixing up bus 1
    PCI/PCIe coreunit 1 is set to bus 2.
    PCI: Fixing up bridge
    PCI: Setting latency timer of device 0000:02:00.0 to 64
    PCI: Fixing up bridge
    PCI: Setting latency timer of device 0000:02:00.1 to 64
    PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
    PCI: Fixing up bus 2
    NET: Registered protocol family 2
    Time: MIPS clocksource has been installed.
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 4096 (order: 3, 32768 bytes)
    TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
    TCP: Hash tables configured (established 4096 bind 4096)
    TCP reno registered
    highmem bounce pool size: 64 pages
    squashfs: version 3.0 (2006/03/15) Phillip Lougher
    io scheduler noop registered (default)
    HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
    N_HDLC line discipline registered.
    Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
    serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
    serial8250: ttyS1 at MMIO 0xb8000400 (irq = 8) is a 16550A
    PPP generic driver version 2.4.2
    MPPE/MPPC encryption/compression module registered
    NET: Registered protocol family 24
    PPPoL2TP kernel driver, V0.18.3
    PPTP driver version 0.8.5
    Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
    Amd/Fujitsu Extended Query Table at 0x0040
    Physically mapped flash: CFI does not contain boot bank location. Assuming top.
    number of CFI chips: 1
    cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
    Flash device: 0x2000000 at 0x1c000000
    Creating 5 MTD partitions on "Physically mapped flash":
    0x00000000-0x00040000 : "pmon"
    0x00040000-0x01fe0000 : "linux"
    0x0013a400-0x009c0000 : "rootfs"
    0x009c0000-0x01fe0000 : "jffs2"
    0x01fe0000-0x02000000 : "nvram"
    Found an serial flash with 0 0KB blocks; total size 0MB
    sflash: found no supported devices
    _nvram_init: allocat header: 2280980480, size= 65536
    usbcore: registered new interface driver hiddev
    usbcore: registered new interface driver usbhid
    drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
    u32 classifier
    OLD policer on
    Netfilter messages via NETLINK v0.30.
    nf_conntrack version 0.5.0 (2048 buckets, 16384 max)
    ip_tables: (C) 2000-2006 Netfilter Core Team
    ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>,

    Dieser Link ist nur für Mitglieder!!! Jetzt kostenlos Registrieren ?


    net/ipv4/netfilter/tomato_ct.c [Jun 9 2013 19:08:29]
    NET: Registered protocol family 1
    NET: Registered protocol family 10
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    NET: Registered protocol family 17
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    VFS: Mounted root (squashfs filesystem) readonly.
    Freeing unused kernel memory: 128k freed
    Warning: unable to open an initial console.
    emf: module license 'Proprietary' taints kernel.
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.20
    wl_module_init: passivemode set to 0x0
    PCI: Enabling device 0000:01:01.0 (0000 -> 0002)
    PCI: Setting latency timer of device 0000:01:01.0 to 64
    eth1: Broadcom BCM4331 802.11 Wireless Controller 5.100.138.20
    PCI: Enabling device 0000:02:01.0 (0000 -> 0002)
    PCI: Setting latency timer of device 0000:02:01.0 to 64
    eth2: Broadcom BCM4331 802.11 Wireless Controller 5.100.138.20
    Algorithmics/MIPS FPU Emulator v1.5
    SCSI subsystem initialized
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    sdhci: Secure Digital Host Controller Interface driver
    sdhci: Copyright(c) Pierre Ossman
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    PCI: Setting latency timer of device 0000:00:04.1 to 64
    ehci_hcd 0000:00:04.1: EHCI Host Controller
    ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:04.1: irq 6, io mem 0x18004000
    ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    PCI: Setting latency timer of device 0000:00:04.0 to 64
    ohci_hcd 0000:00:04.0: OHCI Host Controller
    ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
    ohci_hcd 0000:00:04.0: irq 6, io mem 0x18009000
    usb usb2: configuration #1 chosen from 1 choice
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    usbcore: registered new interface driver usblp
    usblp: USB Printer Device Class driver
    usb 1-1: new high speed USB device using ehci_hcd and address 2
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    vlan1: add 33:33:00:00:00:01 mcast address to master interface
    vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    vlan1: dev_set_allmulti(master, 1)
    vlan1: dev_set_promiscuity(master, 1)
    device eth0 entered promiscuous mode
    device vlan1 entered promiscuous mode
    usb 1-1.4: new high speed USB device using ehci_hcd and address 3
    usb 1-1.4: configuration #1 chosen from 1 choice
    scsi0 : SCSI emulation for USB Mass Storage devices
    device eth1 entered promiscuous mode
    device eth2 entered promiscuous mode
    br0: port 3(eth2) entering forwarding state
    br0: port 2(eth1) entering forwarding state
    br0: port 1(vlan1) entering forwarding state
    vlan2: Setting MAC address to 60 a4 4c 8f c0 29.
    vlan2: add 33:33:00:00:00:01 mcast address to master interface
    vlan2: add 01:00:5e:00:00:01 mcast address to master interface
    IMQ starting with 2 devices...
    IMQ driver loaded successfully.
    Hooking IMQ after NAT on PREROUTING.
    Hooking IMQ before NAT on POSTROUTING.
    scsi 0:0:0:0: Direct-Access Multi Flash Reader 1.00 PQ: 0 ANSI: 0
    sd 0:0:0:0: [sda] 15523840 512-byte hardware sectors (7948 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    sda: sda1 sda2 sda3
    sd 0:0:0:0: [sda] Attached SCSI removable disk
    Adding 2529124k swap on /dev/sda2. Priority:-1 extents:1 across:2529124k
    EXT3-fs: starting recovery.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda3, internal journal
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    EXT3-fs: starting recovery.
    kjournald starting. Commit interval 5 seconds
    EXT3 FS on sda1, internal journal
    EXT3-fs: recovery complete.
    EXT3-fs: mounted filesystem with ordered data mode.
    usb 1-1.2: new full speed USB device using ehci_hcd and address 4
    usb 1-1.2: configuration #1 chosen from 1 choice

    libftdi habe ich installiert und gedacht, damit wäre das Problem behoben, dem ist aber nicht so.


    uname -a

    Linux unknown 2.6.22.19 #5 Sun Jun 9 19:08:32 CEST 2013 mips GNU/Linux


    lsmod

    root@unknown:/tmp/home/root# lsmod
    Module Size Used by Tainted: P
    ip6table_mangle 992 0
    ip6table_filter 704 0
    xt_recent 6800 2
    xt_IMQ 736 0
    imq 2320 0
    usblp 11312 0
    ohci_hcd 17232 0
    ehci_hcd 34640 0
    sdhci 12368 0
    mmc_block 6768 0
    mmc_core 17216 2 sdhci,mmc_block
    vfat 9216 0
    fat 45936 1 vfat
    ext2 55648 0
    ext3 113568 2
    jbd 48352 1 ext3
    mbcache 4528 2 ext2,ext3
    usb_storage 33120 3
    sd_mod 21408 4
    scsi_wait_scan 384 0
    scsi_mod 75488 3 usb_storage,sd_mod,scsi_wait_scan
    leds_usb 2128 0
    led_class 1552 1 leds_usb
    ledtrig_usbdev 2464 1 leds_usb
    nf_nat_pptp 1440 0
    nf_conntrack_pptp 3808 1 nf_nat_pptp
    nf_nat_proto_gre 1072 1 nf_nat_pptp
    nf_conntrack_proto_gre 2464 1 nf_conntrack_pptp
    nf_nat_ftp 1568 0
    nf_conntrack_ftp 5792 1 nf_nat_ftp
    nf_nat_sip 5920 0
    nf_conntrack_sip 19008 1 nf_nat_sip
    nf_nat_h323 5504 0
    nf_conntrack_h323 37152 1 nf_nat_h323
    wl 2617008 0
    dnsmq 2032 1 wl
    et 37344 0
    igs 13584 1 wl
    emf 17568 2 wl,igs


    lsusb


    root@unknown:/tmp/home/root# lsusb
    Bus 001 Device 004: ID 0403:6001
    Bus 001 Device 003: ID 058f:6366
    Bus 001 Device 002: ID 058f:6254
    Bus 002 Device 001: ID 1d6b:0001
    Bus 001 Device 001: ID 1d6b:0002

    Danke für jede Hilfe!

    Gruß
    SR-88
     
    #1
  2. phantom

    Nervigen User Advertisement

  3. derdigge
    Offline

    derdigge Super Elite User Supporter

    Registriert:
    2. September 2012
    Beiträge:
    2.560
    Zustimmungen:
    942
    Punkte für Erfolge:
    113
    Beruf:
    Florist
    AW: Oscam auf DD-WRT, easymouse 2 wird nicht erkannt

    Das alte leiden mir ddwrt .....
    Du brauchst das Kernelmodul :

    ftdi_sio.ko

    Wo du das herbekommst erfährst du nur im ddwrt forum,
    da es genau zu deinem Kernel passen muss.

    Viel Spaß!
     
    #2
  4. uf2k
    Offline

    uf2k Freak

    Registriert:
    20. Juni 2009
    Beiträge:
    295
    Zustimmungen:
    118
    Punkte für Erfolge:
    43
    Ort:
    Schlummerland
    AW: Oscam auf DD-WRT, easymouse 2 wird nicht erkannt

    @SR-88

    Dein Postfach ist voll.....
     
    #3

Diese Seite empfehlen