1. Diese Seite verwendet Cookies. Wenn du dich weiterhin auf dieser Seite aufhältst, akzeptierst du unseren Einsatz von Cookies. Weitere Informationen

Netgear 3500L mit Tomato und Smargo geht nicht!?!?!?

Dieses Thema im Forum "Andere Router Modelle Archiv" wurde erstellt von cojo, 3. Oktober 2010.

  1. cojo
    Offline

    cojo Moderator Digital Eliteboard Team

    Registriert:
    29. Juni 2010
    Beiträge:
    10.012
    Zustimmungen:
    4.138
    Punkte für Erfolge:
    113
    Ort:
    Hamburg
    Homepage:
    Hab das problem,das der Router den Smargo Plus scheinbar nicht erkannt,jedenfalls wird er nirgends angezeigt,nur der USB stick,ist das normal??
    Hab mir heute extra nen Aktiven USB Hub besorgt,hat aber auch nix gebracht.
    Wenn die KArte drin is,blinkt der Smargo,also scheint da ja irgendwas zu passieren

    Kann mir da einer weiterhelfen???

    Conax Karte (Willy Tel)
    Router : Netgear WNR 3500L (letzte Tomato)
    Smargo Plus
    Hama High Speed USB Hub



    cccam :

    SERVER LISTEN PORT : 12000
    ALLOW WEBINFO: yes
    ALLOW TELNETINFO: no
    SHOW EXTENEDED CLIENT INFO : yes
    WEBINFO USERNAME : root
    WEBINFO PASSWORD : admin
    WEBINFO LISTEN PORT : 16001
    SOFTKEY FILE : /mnt/sda1/cs/cccam/SoftCam.Key
    AUTOROLL FILE : /mnt/sda1/cs/cccam/AutoRoll.Key
    STATIC CW FILE : /mnt/sda1/cs/cccam/constant.cw
    CAID PRIO FILE : /mnt/sda1/cs/cccam/CCcam.prio
    PROVIDERINFO FILE : /mnt/sda1/cs/cccam/CCcam.providers
    CHANNELINFO FILE : /mnt/sda1/cs/cccam/CCcam.channelinfo
    SERIAL READER : /dev/ttyUSB0 smartreader+
    SERIAL READER : /dev/ttyUSB1 smartreader+
    SERIAL READER : /dev/ttyUSB2 smartreader+
    SERIAL READER : /dev/ttyUSB3 smartreader+
    SERIAL READER : /dev/ttyUSB4 smartreader+
    SMARTCARD WRITE DELAY: /dev/tty 10000
    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB0 3570000
    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB1 3570000
    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB2 3570000
    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB3 3570000
    SMARTCARD CLOCK FREQUENCY: /dev/ttyUSB4 3570000
    TRY ALL CHIDS : /dev/ttyUSB0
    BOXKEY: /dev/ttyUSB0 00 00 00 00
    SHOW TIMING : yes
    DEBUG : no
    DISABLE EMM : no
    EXTRA EMM LEVEL : no
    #MINIMUM DOWNHOPS: 1



    Hier mal der lsusb :
    Bus 001 Device 005: ID 0403:6001
    Bus 001 Device 003: ID 090c:1000
    Bus 001 Device 002: ID 05e3:0608
    Bus 001 Device 001: ID 1d6b:0002



    dmesg :

    Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #2 Sat Sep 4 02:34:21 EDT 2010
    CPU revision is: 00019740
    Found a 8MB ST compatible serial flash
    Determined physical RAM map:
    memory: 04000000 @ 00000000 (usable)
    On node 0 totalpages: 16384
    Normal zone: 128 pages used for memmap
    Normal zone: 0 pages reserved
    Normal zone: 16256 pages, LIFO batch:3
    Built 1 zonelists. Total pages: 16256
    Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200
    Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
    Primary data cache 32kB, 4-way, linesize 32 bytes.
    Synthesized TLB refill handler (20 instructions).
    Synthesized TLB load handler fastpath (32 instructions).
    Synthesized TLB store handler fastpath (32 instructions).
    Synthesized TLB modify handler fastpath (31 instructions).
    PID hash table entries: 256 (order: 8, 1024 bytes)
    CPU: BCM4716 rev 1 pkg 10 at 453 MHz
    Using 226.500 MHz high precision timer.
    console [ttyS0] enabled
    Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    Memory: 61860k/65536k available (2290k kernel code, 3620k reserved, 471k data, 112k init, 0k highmem)
    SLUB: Genslabs=6, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
    Calibrating delay loop... 225.28 BogoMIPS (lpj=112640)
    Mount-cache hash table entries: 512
    NET: Registered protocol family 16
    PCI: Using membase 8000000
    PCI: Disabled
    PCI: Fixing up bus 0
    PCI: Fixing up bus 1
    Time: MIPS clocksource has been installed.
    NET: Registered protocol family 2
    IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    TCP established hash table entries: 2048 (order: 2, 16384 bytes)
    TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
    TCP: Hash tables configured (established 2048 bind 2048)
    TCP reno registered
    squashfs: version 3.0 (2006/03/15) Phillip Lougher
    io scheduler noop registered (default)
    HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
    N_HDLC line discipline registered.
    Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
    serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
    PPP generic driver version 2.4.2
    NET: Registered protocol family 24
    PPPoL2TP kernel driver, V0.17
    PPTP driver version 0.8.5-rc1
    pflash: found no supported devices
    Creating 6 MTD partitions on "sflash":
    0x00000000-0x00040000 : "pmon"
    0x00040000-0x007a0000 : "linux"
    0x0012d000-0x006b0000 : "rootfs"
    0x006b0000-0x007a0000 : "jffs2"
    0x007f0000-0x00800000 : "nvram"
    0x007a0000-0x007f0000 : "board_data"
    u32 classifier
    OLD policer on
    Netfilter messages via NETLINK v0.30.
    nf_conntrack version 0.5.0 (512 buckets, 4096 max)
    GRE over IPv4 demultiplexor driver
    ip_tables: (C) 2000-2006 Netfilter Core Team
    net/ipv4/netfilter/tomato_ct.c [Sep 4 2010 02:32:44]
    NET: Registered protocol family 1
    NET: Registered protocol family 10
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    NET: Registered protocol family 17
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    VFS: Mounted root (squashfs filesystem) readonly.
    Freeing unused kernel memory: 112k freed
    Warning: unable to open an initial console.
    et: module license 'unspecified' taints kernel.
    PCI: Setting latency timer of device 0000:00:02.0 to 64
    eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.56.46
    PCI: Setting latency timer of device 0000:00:01.0 to 64
    eth1: Broadcom BCM4329 802.11 Wireless Controller 5.10.56.46
    Algorithmics/MIPS FPU Emulator v1.5
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    SCSI subsystem initialized
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    PCI: Setting latency timer of device 0000:00:04.1 to 64
    ehci_hcd 0000:00:04.1: EHCI Host Controller
    ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
    ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
    usb usb1: configuration #1 chosen from 1 choice
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 2 ports detected
    usbcore: registered new interface driver usblp
    usblp: USB Printer Device Class driver
    usb 1-1: new high speed USB device using ehci_hcd and address 2
    vlan1: add 33:33:00:00:00:01 mcast address to master interface
    vlan1: add 01:00:5e:00:00:01 mcast address to master interface
    vlan1: dev_set_promiscuity(master, 1)
    device eth0 entered promiscuous mode
    device vlan1 entered promiscuous mode
    usb 1-1: configuration #1 chosen from 1 choice
    hub 1-1:1.0: USB hub found
    hub 1-1:1.0: 4 ports detected
    device eth1 entered promiscuous mode
    br0: port 2(eth1) entering learning state
    br0: port 1(vlan1) entering learning state
    br0: topology change detected, propagating
    br0: port 2(eth1) entering forwarding state
    br0: topology change detected, propagating
    br0: port 1(vlan1) entering forwarding state
    vlan2: Setting MAC address to c0 3f 0e 92 87 9f.
    vlan2: add 33:33:00:00:00:01 mcast address to master interface
    vlan2: add 01:00:5e:00:00:01 mcast address to master interface
    usb 1-1.1: new high speed USB device using ehci_hcd and address 3
    usb 1-1.1: configuration #1 chosen from 1 choice
    scsi0 : SCSI emulation for USB Mass Storage devices
    usb 1-1.2: new full speed USB device using ehci_hcd and address 4
    usb 1-1.2: configuration #1 chosen from 1 choice
    scsi 0:0:0:0: Direct-Access INTENSO USB 1100 PQ: 0 ANSI: 0 CCS
    sd 0:0:0:0: [sda] 7831552 512-byte hardware sectors (4010 MB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    sda: sda1 sda2
    sd 0:0:0:0: [sda] Attached SCSI removable disk
    EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
    usb 1-1.2: USB disconnect, address 4
    usb 1-1.2: new full speed USB device using ehci_hcd and address 5
    usb 1-1.2: configuration #1 chosen from 1 choice



    lsmod :
    Module Size Used by Tainted: P
    nls_cp437 5344 1
    usblp 15344 0
    ehci_hcd 40144 0
    vfat 11776 1
    fat 56112 1 vfat
    ext2 67712 1
    ext3 136576 0
    jbd 62080 1 ext3
    mbcache 7280 2 ext2,ext3
    usb_storage 50048 2
    sd_mod 27440 3
    scsi_wait_scan 960 0
    scsi_mod 105344 3 usb_storage,sd_mod,scsi_wait_scan
    usbcore 146544 4 usblp,ehci_hcd,usb_storage
    nf_nat_pptp 2592 0
    nf_conntrack_pptp 6000 1 nf_nat_pptp
    nf_nat_proto_gre 2128 1 nf_nat_pptp
    nf_conntrack_proto_gre 4160 1 nf_conntrack_pptp
    nf_nat_ftp 2816 0
    nf_conntrack_ftp 8160 1 nf_nat_ftp
    nf_nat_sip 4416 0
    nf_conntrack_sip 9024 1 nf_nat_sip
    nf_nat_h323 7360 0
    nf_conntrack_h323 50016 1 nf_nat_h323
    wl 2051584 0
    igs 17904 1 wl
    emf 22656 2 wl,igs
    et 59104 0


    weiss echt nicht weiter,kann mir hier einer helfen????

    habs nach angehägter anleitung gemacht
     
    #1

Diese Seite empfehlen