1. Diese Seite verwendet Cookies. Wenn du dich weiterhin auf dieser Seite aufhältst, akzeptierst du unseren Einsatz von Cookies. Weitere Informationen

keine USB Geräte nach neustart

Dieses Thema im Forum "Fritzbox Archiv" wurde erstellt von Hundekuchen2, 22. Dezember 2011.

  1. Hundekuchen2
    Offline

    Hundekuchen2 Ist gelegentlich hier

    Registriert:
    28. Oktober 2009
    Beiträge:
    32
    Zustimmungen:
    1
    Punkte für Erfolge:
    8
    Hallo Zusammen,

    ich bin jetzt auf Oscam umgestiegen und habe jetzt nen König Hub passiv mit 2x Maxdigital Smargo und nen Kingston USb Stick drannen. Das Problem ist wenn ich die Box neustarte ist vieleicht von 6x neustarten ein Start dabei wo er mit dann den Stick und die Smargos anzeigt, ansonsten Fehlermeldung (siehe Log). Wenn der Hub nicht drannen ist, sondern nur der Stick geht es ohne Probleme und der Stick wird bei jeden neustart angezeigt. Sobald der Hub drann ist, wie gesagt werden die Geräte nur sehr selten. Wenn im laufenden Betrieb die Geräte vom Hub entferne und dann einzeln wieder anschließe erkennt er die Geräte nach und nach.

    Ich hoffe Ihr könnt mir helfen.

    Hier mal der Log

    Dec 22 12:05:50 fritz.box kernel: SCSI subsystem initialized
    Dec 22 12:05:50 fritz.box kernel: usbcore: registered new interface driver usbfs
    Dec 22 12:05:50 fritz.box kernel: usbcore: registered new interface driver hub
    Dec 22 12:05:50 fritz.box kernel: usbcore: registered new device driver usb
    Dec 22 12:05:50 fritz.box kernel: pcibios_read_config: accessing present PCI slot : 14, where 0, size 4
    Dec 22 12:05:50 fritz.box kernel: pci 0000:00:0e.0: reg 10 32bit mmio: [0x000000-0x00ffff]
    Dec 22 12:05:50 fritz.box kernel: Master and Slave Enabled
    Dec 22 12:05:50 fritz.box kernel: NET: Registered protocol family 8
    Dec 22 12:05:50 fritz.box kernel: NET: Registered protocol family 20
    Dec 22 12:05:50 fritz.box kernel: hub 1-0:1.0: 1 port detected
    Dec 22 12:05:50 fritz.box kernel: AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Jul 1 2011 14:41:44)
    Dec 22 12:05:50 fritz.box kernel: [simple-profiling]: no performance counters implemented
    Dec 22 12:05:50 fritz.box kernel: [simple-profiling]: no performance counters implemented
    Dec 22 12:05:50 fritz.box kernel: [avm]: AVM Simple Profiling enabled.
    Dec 22 12:05:50 fritz.box kernel: Serial: SERIAL_AVM_8250 driver
    Dec 22 12:05:50 fritz.box kernel: [uart_avm_request_port] request port 0
    Dec 22 12:05:50 fritz.box kernel: ttyS0 at MMIO 0x0 (irq = 15) is a PORT_16550A
    Dec 22 12:05:50 fritz.box kernel: physmap platform flash device: 01000001 at 10000000
    Dec 22 12:05:50 fritz.box kernel: physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
    Dec 22 12:05:50 fritz.box kernel: Amd/Fujitsu Extended Query Table at 0x0040
    Dec 22 12:05:50 fritz.box kernel: Don't use write buffer on ST flash M29W128G
    Dec 22 12:05:50 fritz.box kernel: mcfw: IGMPv3 fast forwarding
    Dec 22 12:05:50 fritz.box kernel: NET: Registered protocol family 10
    Dec 22 12:05:50 fritz.box kernel: NET: Registered protocol family 17
    Dec 22 12:05:50 fritz.box kernel: PCI_STATUS_SET: 60000
    Dec 22 12:05:50 fritz.box kernel: PCI_STATUS_CLR: 60000
    Dec 22 12:05:50 fritz.box kernel: PCI_HOST_INT_EN: 0
    Dec 22 12:05:50 fritz.box kernel: PCI_HOST_INT_CLR: 0
    Dec 22 12:05:50 fritz.box kernel: PCI_BE_INT_En: 0
    Dec 22 12:05:50 fritz.box kernel: PCI_BE_INT_CLR: 0
    Dec 22 12:05:50 fritz.box kernel: [pci_int_init] done
    Dec 22 12:05:50 fritz.box kernel: TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
    Dec 22 12:05:50 fritz.box kernel: mount on mtd3 and mtd4 (double buffering)
    Dec 22 12:05:50 fritz.box kernel: Adam2 environment variables API installed.
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device descriptor read/64, error -71
    Dec 22 12:05:50 fritz.box kernel: [squashfs] use lzma compression
    Dec 22 12:05:50 fritz.box kernel: VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
    Dec 22 12:05:50 fritz.box kernel: Freeing bootloader memory: 1024k freed
    Dec 22 12:05:50 fritz.box kernel: Freeing unused kernel memory: 160k freed
    Dec 22 12:05:50 fritz.box kernel: [uart_avm_startup] Setup IRQ 15
    Dec 22 12:05:50 fritz.box kernel: [uart_avm_set_termios] old_dll=98, old_dlh=0
    Dec 22 12:05:50 fritz.box kernel: [uart_avm_set_termios] baudrate=38400, quot=98, dll=98, dlh=0
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device descriptor read/64, error -71
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: new full speed USB device using musb_hdrc and address 3
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device descriptor read/64, error -71
    Dec 22 12:05:50 fritz.box kernel: TFFS Name Table G
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device descriptor read/64, error -71
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: new full speed USB device using musb_hdrc and address 4
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device not accepting address 4, error -71
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: new full speed USB device using musb_hdrc and address 5
    Dec 22 12:05:50 fritz.box kernel: usb 1-1: device not accepting address 5, error -71
    Dec 22 12:05:50 fritz.box kernel: hub 1-0:1.0: unable to enumerate USB device on port 1
    Dec 22 12:05:50 fritz.box kernel: led_modul_Fritz_Box_7270plus: module license '
    Dec 22 12:05:50 fritz.box kernel: (C) Copyright 2008 by AVM
    Dec 22 12:05:50 fritz.box kernel: ' taints kernel.
    Dec 22 12:05:50 fritz.box kernel: Disabling lock debugging due to kernel taint
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 1 name power
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 9 name internet
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 27 name festnetz
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 28 name wlan
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 17 name dual1
    Dec 22 12:05:50 fritz.box kernel: [led_gpio_bit_driver_init] gpio 35 name dual2
    Dec 22 12:05:50 fritz.box kernel: [button_init] name button_wlan gpio 25 active low
    Dec 22 12:05:50 fritz.box kernel: [button_init] name button_dect gpio 23 active low
    Dec 22 12:05:50 fritz.box kernel: [button_init] name button_both gpio 0 active high
    Dec 22 12:05:50 fritz.box kernel: AVM_WATCHDOG: System Init UEberwachung 480 Sekunden
    Dec 22 12:05:50 fritz.box kernel: [avm_debug]standard kernel-messages
    Dec 22 12:05:50 fritz.box kernel: [piglet]use gpio-settings for 145
    Dec 22 12:05:50 fritz.box kernel: patch_dectfw: c0b30000, totallen = 68511(10b9f)
    Dec 22 12:05:50 fritz.box kernel: patch_dectfw: patch_adress: f103a max_len: 26 with Version 2 Len: 17
    Dec 22 12:05:50 fritz.box kernel: dect_loader: fast-bootmode
    Dec 22 12:05:50 fritz.box kernel: *
    Dec 22 12:05:50 fritz.box kernel: *************************************************************************************************************************************
    Dec 22 12:05:50 fritz.box kernel: dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_488.hex' successfull
    Dec 22 12:05:50 fritz.box kernel: [piglet]bitfile '/lib/modules/bitfile.bit'
    Dec 22 12:05:50 fritz.box kernel: [piglet] clock from pll3(384000000)
    Dec 22 12:05:50 fritz.box kernel: [piglet] bitfile 169293 bytes done
    Dec 22 12:05:50 fritz.box kernel: [piglet]TDM: FS: 8000 Hz CLK:2047965 Hz
    Dec 22 12:05:50 fritz.box kernel: JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc.
    Dec 22 12:05:50 fritz.box kernel: [4294938616]system-load 6 23 tasks:21 % curr:rc.S(1 %) max:init(13 %, pid:1), readytorun: 1, pgfault 1402/s (max 1 avg 1.0)
    Dec 22 12:05:50 fritz.box kernel: loop: module loaded
    Dec 22 12:05:50 fritz.box kernel: [pcmlink]svn: 1385
    Dec 22 12:05:50 fritz.box kernel: driver params overwritten io_addr=0x0 irq_num=0
    Dec 22 12:05:50 fritz.box kernel: [pcmlink]c55: simple checksum: 18EF96A
    Dec 22 12:05:50 fritz.box kernel: capicodec_init()
    Dec 22 12:05:50 fritz.box kernel: [capi_codec] support fax
    Dec 22 12:05:50 fritz.box kernel: [capi_codec] support Codecs
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 8 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS
    Dec 22 12:05:50 fritz.box kernel: [4294940652]system-load 100 % 59 tasks:5 % curr:multid(1 %) max:busybox(1 %, pid:565), readytorun: 1, pgfault 1518/s (max 1 avg 1.0)
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] ioctl set inventory invoked
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] dsl serial number successfully set to "303032344645364538333741204621426f78373237302037342e30352e303500"
    Dec 22 12:05:50 fritz.box kernel: eth: port 0 status 2 throttle 0
    Dec 22 12:05:50 fritz.box kernel: eth: port 1 status 1 throttle 1
    Dec 22 12:05:50 fritz.box kernel: [cpmac] [adm_power_config] tried to set a mode 1 that is not possible for this port 1.
    Dec 22 12:05:50 fritz.box kernel: [avm_power] : ethernet switch failed
    Dec 22 12:05:50 fritz.box kernel: eth: port 2 status 1 throttle 1
    Dec 22 12:05:50 fritz.box kernel: [cpmac] [adm_power_config] tried to set a mode 1 that is not possible for this port 2.
    Dec 22 12:05:50 fritz.box kernel: [avm_power] : ethernet switch failed
    Dec 22 12:05:50 fritz.box kernel: eth: port 3 status 1 throttle 1
    Dec 22 12:05:50 fritz.box kernel: [cpmac] [adm_power_config] tried to set a mode 1 that is not possible for this port 3.
    Dec 22 12:05:50 fritz.box kernel: [avm_power] : ethernet switch failed
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] hwrev=145 is_ATA_Ld_Hw=0
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] from DSL to ATA Mode
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] DSP in IDLE Mode
    Dec 22 12:05:50 fritz.box kernel: ADDRCONF(NETDEV_UP): cpmac0: link is not ready
    Dec 22 12:05:50 fritz.box kernel: [dsl_ur8] SARAS PWDREG = 0x8000
    Dec 22 12:05:50 fritz.box kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
    Dec 22 12:05:50 fritz.box kernel: device eth0 entered promiscuous mode
    Dec 22 12:05:50 fritz.box kernel: device cpmac0 entered promiscuous mode
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: [4294941707]system-load 100 % 56 tasks:42 % curr:rc.inetd(0 %) max:ctlmgr(27 %, pid:752), readytorun: 3, pgfault 5062/s (max 2 avg 1.0)
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: ADDRCONF(NETDEV_CHANGE): cpmac0: link becomes ready
    Dec 22 12:05:50 fritz.box kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    Dec 22 12:05:50 fritz.box kernel: lan: port 1(eth0) entering forwarding state
    Dec 22 12:05:50 fritz.box kernel: dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: %B
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] calibration data blocks found = 1
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] Got calibration data version 2 for instance #1
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] Loading "/lib/modules/wlan_eeprom_hw0.bin"
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] Patching calibration data into eeprom
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] Patching MAC address to 00:24:fe:48:2d:af
    Dec 22 12:05:50 fritz.box kernel: [wlan_eeprom] Customer data="7270V3_V7B13_Dualband_CTL"
    Dec 22 12:05:50 fritz.box kernel: wlanfw: Init.
    Dec 22 12:05:50 fritz.box kernel: avm_wlan_memory: Init.
    Dec 22 12:05:50 fritz.box kernel: ath_hal: 0.9.14.25 (AR5416, REGOPS_FUNC)
    Dec 22 12:05:50 fritz.box kernel: get_wlan_memory: (Rx) dd->dd_desc: b7fa4000, dd->dd_desc_paddr: 17fa4000, dd->dd_desc_len: 9510, *bf: 97fae000
    Dec 22 12:05:50 fritz.box kernel: get_wlan_memory: (Tx) dd->dd_desc: b7f60000, dd->dd_desc_paddr: 17f60000, dd->dd_desc_len: 246c0, *bf: 97f85000
    Dec 22 12:05:50 fritz.box kernel: ath_descdma_setup: beacon DMA map: b5de1000 (1152) -> physical 15de1000 (1152)
    Dec 22 12:05:50 fritz.box kernel: dfs_init_radar_filters: dfs->dfs_rinfo.rn_numradars: 0
    Dec 22 12:05:50 fritz.box kernel: DFS min filter rssiThresh = 21
    Dec 22 12:05:50 fritz.box kernel: DFS max pulse dur = 131 ticks
    Dec 22 12:05:50 fritz.box kernel: ic_chainmask=3x3
    Dec 22 12:05:50 fritz.box kernel: wifi0: 11na rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
    Dec 22 12:05:50 fritz.box kernel: wifi0: 11na MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
    Dec 22 12:05:50 fritz.box kernel: wifi0: 11ng rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
    Dec 22 12:05:50 fritz.box kernel: wifi0: 11ng MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
    Dec 22 12:05:50 fritz.box kernel: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
    Dec 22 12:05:50 fritz.box kernel: [4294944807]system-load 100 % 68 tasks:54 % curr:rc.wlan(2 %) max:playerd_tables(42 %, pid:1813), readytorun: 3, pgfault 3733/s (max 3 avg 1.8)
    Dec 22 12:05:50 fritz.box kernel: AVM_WATCHDOG: System Init UEberwachung abgeschlossen (405820 ms noch verfuegbar)
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=0 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=100 mul=65 div=10 offset=1793 NormP=2443 mW -> SumNormP=2443 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=100 mul=84 div=10 offset=100 NormP=940 mW -> SumNormP=3383 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnnt: norm_power_rate=100 act_rate=0 mul=1 div=1 offset=0 NormP=100 mW -> SumNormP=3483 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_isdnte: norm_power_rate=100 act_rate=0 mul=1 div=1 offset=0 NormP=100 mW -> SumNormP=3583 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_analog: norm_power_rate=200 act_rate=0 mul=141 div=10 offset=100 NormP=2920 mW -> SumNormP=6503 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_dect: norm_power_rate=100 act_rate=0 mul=200 div=78 offset=150 NormP=406 mW -> SumNormP=6909 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_ethernet: norm_power_rate=467 act_rate=50331955 mul=1 div=1 offset=50 NormP=517 mW -> SumNormP=7426 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_dsl: norm_power_rate=100 act_rate=50 mul=15 div=1 offset=0 NormP=1500 mW -> SumNormP=8926 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_usb_host: norm_power_rate=500 act_rate=0 mul=55 div=10 offset=0 NormP=2750 mW -> SumNormP=11676 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_usb_client: norm_power_rate=0 act_rate=0 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=11676 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_charge: norm_power_rate=446 act_rate=0 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=11676 mW
    Dec 22 12:05:50 fritz.box kernel: [avm_power] pm_ressourceinfo_scriptparse: powerdevice_loadrate: norm_power_rate=100 act_rate=100 mul=29 div=10 offset=-17 NormP=273 mW -> SumNormP=11949 mW
    Dec 22 12:05:50 fritz.box kernel: SysRq : Changing Loglevel
    Dec 22 12:05:50 fritz.box kernel: Loglevel set to 4
    Dec 22 12:05:51 fritz.box FREETZMOD: Starting inetd ... done.
    Dec 22 12:05:51 fritz.box kernel: [4294945807]system-load 100 % 74 tasks:8 % curr:modreg(0 %) max:rc.S(1 %, pid:24), readytorun: 1, pgfault 5419/s (max 1 avg 1.0)
    Dec 22 12:05:51 fritz.box FREETZMOD: Setting up SSH authorized_keys for root ... done.
    Dec 22 12:05:52 fritz.box dropbear[2600]: Running in background
    Dec 22 12:05:54 fritz.box FREETZMOD: Starting openvpn ... done.
    Dec 22 12:06:04 fritz.box hostapd: ath0: STA d8:a2:5e:26:79:09 IEEE 802.11: associated
    Dec 22 12:06:04 fritz.box hostapd: ath0: STA d8:a2:5e:26:79:09 WPA: pairwise key handshake completed (RSN)
    Dec 22 12:06:19 fritz.box hostapd: ath0: STA 00:1e:2a:11:5a:17 IEEE 802.11: associated
    Dec 22 12:06:19 fritz.box hostapd: ath0: STA 00:1e:2a:11:5a:17 WPA: pairwise key handshake completed (WPA)
    Dec 22 12:06:19 fritz.box hostapd: ath0: STA 00:1e:2a:11:5a:17 WPA: group key handshake completed (WPA)
    Dec 22 12:06:19 fritz.box kernel: [4294948627]system-load 7 75 tasks:8 % curr:modreg(0 %) max:feedd(2 %, pid:1805), readytorun: 1, pgfault 1973/s (max 2 avg 1.0)
    :
     
    #1
  2. phantom

    Nervigen User Advertisement

  3. märklin
    Online

    märklin Guest

    AW: keine USB Geräte nach neustart

    na dann nimm mal einen anderen HUB

    Dieser Link ist nur für Mitglieder!!! Jetzt kostenlos Registrieren ?

     
    #2

Diese Seite empfehlen