Digital Eliteboard - Das Digitale Technik Forum

Registriere dich noch heute kostenloses um Mitglied zu werden! Sobald du angemeldet bist, kannst du auf unserer Seite aktiv teilnehmen, indem du deine eigenen Themen und Beiträge erstellst und dich über deinen eigenen Posteingang mit anderen Mitgliedern unterhalten kannst! Zudem bekommst du Zutritt zu Bereiche, welche für Gäste verwehrt bleiben

Hardware Reparatur- Netzteil

Holzwurm0101

Best Member
Boardveteran
Registriert
25. November 2007
Beiträge
7.020
Reaktionspunkte
2.994
Punkte
383
Ort
im Norden
Symptom: Blinkende rote Power-Taste auf der Frontplatte

Jeweils dabei die deutsche Übersetzung

The problem is most likely that the power supply is not working correctly.​
Das Problem ist wahrscheinlich, dass das Netzteil ist nicht richtig funktioniert.
To try and isolate and fix the problem proceed as follows.​
Zu versuchen und zu isolieren und die Behebung des Problems gehen Sie wie folgt vor.
Disconnect the machine from the mains and all other connections and place the TM9100 on a flat surface.​
Trennen Sie das Gerät vom Netz und alle anderen Verbindungen und die TM9100 auf einer ebenen Fläche.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Remove the screws from the rear of the case and remove the top cover​
Entfernen Sie die Schrauben von der Rückseite des Gehäuses und entfernen Sie die obere Abdeckung
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Locate the main power supply Printed Circuit Board (PCB).​
Suchen Sie die Haupt-Stromversorgung Printed Circuit Board (PCB).
In the above picture this is towards the left hand side of the TM9100.​
In dem obigen Bild ist auf der linken Seite der TM9100.
Proceed to remove the power supply PCB by removing the mains PCB connector.​
Gehen Sie, um die Stromversorgung durch die Beseitigung von PCB-Leiterplatten-Netz-Anschluss.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Then remove the main motherboard connector.​
Dann entfernen Sie die wichtigsten Motherboard Anschluss.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Then remove the Hard Disk Drive power cable.​
Dann entfernen Sie die Festplatte Netzkabel.
It is easier to remove this from the Hard Disk Drive than from the power supply PCB.​
Es ist einfacher, entfernen Sie diesen von der Festplatte als von der Stromversorgung Leiterplatten.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Remove the screws holding the power supply PCB to the main case and carefully remove the assembly and place it on your working surface.​
Entfernen Sie die Schrauben der Stromversorgung PCB zu den wichtigsten Fall sorgfältig und entfernen Sie die Montage und legen Sie sie auf Ihre Arbeitsfläche.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Inspect the capacitors for signs of damage.​
Überprüfen Sie die Kondensatoren auf Anzeichen von Schäden.
In the following image you can see the original capacitor (being held) and the replacement one in situ on the board.​
Im folgenden Bild sehen Sie die Original-Kondensator (statt) und den Ersatz eines in-situ auf dem Brett.
Notice that the top of the original capacitor is bulging upwards slightly (and is reflecting more light in the photo).​
Beachten Sie, dass die Spitze der ursprünglichen Kondensator ist prall leicht nach oben (und ist, die mehr Licht auf dem Foto).
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Damage can be indicated by either the outer case being blown open, or the top of the capacitor bulging or sometimes leakage from the capacitor or occasionally burn marks.​
Schäden können entweder durch den äußeren Fall wird geblasen öffnen, oder die Spitze des Kondensators prall oder manchmal Auslaufen aus dem Kondensator oder gelegentlich brennen Marken.
If you have located a damaged capacitor they are readily available as spares (cheaply) and are relatively easily replaced.​
Wenn Sie nur einen Kondensator beschädigt sie leicht verfügbar sind als Ersatzteile (billig) und sind relativ leicht ersetzt werden.
However you should only proceed to repair if you feel you are competent with a soldering iron and of course there are the obvious safety issues involved with that!​
Aber Sie sollten nur dann zu reparieren, wenn Sie glauben, dass Sie zuständig sind mit einem Lötkolben und natürlich gibt es die offensichtliche Probleme mit der Sicherheit, dass!
Make a note of the capacitor number Cxxx on the printed circuit board (you may find a small magnifying glass helpful here).​
Notieren Sie die Zahl Cxxx Kondensator auf der Leiterplatte (Sie können eine kleine Lupe hilfreich hier).
Now a little information on capacitors may help here … if you are not sure what they are here is an example of a particular capacitor called an electrolytic capacitor (these are commonly used in power supplies and are quite often the cause a of a power supply failure).​
Nun wird ein wenig Informationen über Kondensatoren können hier ... Wenn Sie nicht sicher sind, was sie sind hier ist ein Beispiel für einen bestimmten Kondensator genannt Elektrolytkondensator (diese werden üblicherweise in Stromversorgungen und sind oft die Ursache ein von der Stromversorgung ).
The left hand picture is a new one and the right hand picture is the original one that had failed.​
In der linken Bild ist eine neue und die rechte Hand Bild ist das Original, die gescheitert ist.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

If you look at the left hand picture you will notice that there is a row of negative signs down one side of the capacitor.​
Wenn Sie sich auf der linken Bild werden Sie feststellen, dass es eine Reihe von negativen Zeichen nach einer Seite des Kondensators.
This is important to note.​
Dies ist wichtig zu beachten.
Capacitors are normally polarised (they have a +ve and -ve terminal).​
Kondensatoren werden in der Regel polarisiert (sie haben eine + ve und-ve-Terminal).
So they must be replaced in the circuit board the same way around.​
So müssen sie ersetzt werden in der Platine die gleiche Weise um.
So have a good look at the failed capacitor and note which way around it is, and WRITE IT DOWN, do not try to remember it as once you've turned the board around a few times you may forget it's original orientation.​
So haben Sie einen guten Blick auf die gescheiterten Kondensator und beachten Sie die Art und Weise um ihn herum ist, und schreiben Sie es auf, versuchen Sie nicht einmal daran erinnern, wie Sie sich der Vorstand um ein paar Mal können Sie es vergessen haben den ursprünglichen Ausrichtung.
Now turn the board over and locate the two terminals from your failed component on the reverse side of the board​
Jetzt drehen Sie den über Bord und die beiden Terminals von Ihrer Komponente nicht auf der Rückseite der Platine
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

Check you have correctly located both of the terminals again, just to be sure!​
Überprüfen Sie haben richtig liegt sowohl der Terminals wieder, nur um sicher zu gehen!
You may find that they are marked with the same identification Cxxx (in my case C201).​
Sie können feststellen, dass sie mit der gleichen Identifikation Cxxx (in meinem Fall C201).
Offer up the soldering iron to one of the two terminals and allow the solder to melt, if you have a desoldering tool you can use it to clear the terminal (and pcb hole) of solder.​
Angebot der Lötkolben zu einem der beiden Terminals und dem Lot zu schmelzen, wenn Sie einen Auslöten Werkzeug, das Sie es benutzen können, um den Anschluss (und PCB-Loch) des Lotes.
Du musst dich Anmelden oder Registrieren um diesen link zusehen!
Du musst dich Anmelden oder Registrieren um diesen link zusehen!
Du musst dich Anmelden oder Registrieren um diesen link zusehen!

If you don't have a desoldering tool it is possible to remove the capacitor by alternately heating the terminals and pulling gently on the capacitor to work it out slowly, although this is a little tedious and can make it awkward to insert the new capacitor if the PCB has not been properly cleared of solder.​
Wenn Sie noch nicht über ein Auslöten Tool ist es möglich, entfernen Sie den Kondensator abwechselnd durch die Erwärmung der Terminals und ziehen leicht auf den Kondensator auf, es langsam, auch wenn dies ein wenig langweilig und kann es umständlich, um die neue Kondensator, wenn der PCB wurde nicht ordnungsgemäß gelöscht des Lotes.
Having removed the capacitor and cleared the PCB holes of solder as best you can, insert the new capacitor remembering to orient it with respect to it's polarity (-ve in the correct hole).​
Nachdem der Kondensator entfernt und gelöscht, die PCB-Löcher des Lotes so gut Sie können, fügen Sie den neuen Kondensator Erinnerung zu orientieren sie im Hinblick auf seine Polarität (-ve in der richtigen Loch).
CHECK with your notes you have done this correctly.​
Wenden Sie sich an Ihre Notizen Sie dies getan haben, richtig.
Then gently bend the legs of the capacitor slightly outwards so that the capacitor is held in the circuit board.​
Dann biegen Sie vorsichtig die Beine des Kondensators leicht nach außen, so dass der Kondensator wird in der Platine.
Note that you should fully insert the capacitor as far as it will go.​
Beachten Sie, dass Sie sollten sich voll und ganz Legen Sie die Kondensator so weit wie möglich gehen.
Solder the new one in place on both terminals.​
Löten Sie das neue in auf beiden Terminals.
If you have a multimeter it would be wise to check that you have continuity from the pcb track to the each of the legs of the capacitor in turn (to avoid a "dry" joint).​
Wenn Sie ein Multimeter wäre es sinnvoll zu prüfen, ob Sie die Kontinuität von der PCB-Spur an den jedes der Beine des Kondensators wiederum (um eine "trockene" gemeinsam).
If you don't have a multimeter, don't worry just ensure that the new capacitor is firmly in place.​
Wenn Sie noch nicht über ein Multimeter, machen Sie sich keine Sorgen nur sicherzustellen, dass die neue Kondensator ist fest etabliert.
Then carefully trim the excess terminals with a pair of side cutters.​
Dann schneiden Sie die sorgfältig über Terminals mit einem Paar Seite Messer.
If you have more than one failed capacitor you will need to repeat this for the others.​
Wenn Sie mehr als eine nicht-Kondensator müssen Sie Wiederholen Sie diesen Vorgang für die anderen.
You are then ready to reinstall the PCB (a reverse of the above removal process).​
Sie sind dann bereit, die von PCB (eine Umkehrung des oben entfernen).
Then check all of your connections are correct.​
Dann prüfen Sie alle Verbindungen korrekt sind.
Reconnect the machine and test.​
Schließen Sie das Gerät und testen.


Übersetung aus dem Englischen
 
Zurück
Oben